light Seat Ateca 2020 User Guide

Lights
Using the Keyless Access* system (only
cl osing)

Operation

It lights up
Left or right turn signal.
The control lamp flashes twice as f ast when a t
urn
signal is faulty.
Hazard warning lights on

Lights
position  or , accor ding t
o the l e
v el of ex-
terior lighting.
When the light switch is in position , a light sensor automatically switches dipped beam
on and off (including the control and instru-
ment lighting) or the daytime running lights
depending on the level of exterior lighting.
Motorway light*
The motorway light is available on vehicles
equipped with full-LED lights.
The function is connected and disconnected
via the corresponding Easy Connect system
menu.

Lights
Note

Lights
switching off the headlights is count ed fr
om
when the l ast door or boot hat
ch is cl
osed.
The “Coming Home” lighting turns off in
the following cases:

Operation
6. Use the warning triangle to draw the at- tention of other r
oad users to your v
ehicl
e.
7. Always take the vehicle key with you when you leave the vehicle
.
All turn signals flash simultaneously when the
hazard warning lights are switched on. The
two turn signal turn signal lamps   and the
turn signal lamp in the switch  will flash at
the same time. The simultaneous hazard
warning lights also work when the ignition is
switched off.
Emergency braking warning
If the vehicle brakes suddenly and continu-
ously at a speed of more than 80 km/h (50
mph), the brake light flashes several times per
second to warn the vehicles driving behind. If
you continue braking, the hazard warning
lights will come on automatically when the
vehicle comes to a standstill. They switch off
automatically when the vehicle starts to
move again. WARNING

Lights
Setting 2
All seats occupied, luggage compart-
ment full. With trailer and minimum
dr
awbar l
oad.
Setting 3 Driver only, luggage compartment full
Driving with trailer and maximum
drawbar l
oad. Dynamic headlight range control
The control is not mounted in vehicl
es with
dynamic headlight r

ange control. The head-
light range is automatically adjusted accord-
ing to the vehicle load status when they are
switched on. WARNING
Heavy objects in the vehicle may mean
that the headlights dazzle and distract oth- er drivers. This coul d r

esult in a serious ac-
cident.

Operation
Knob Function
 Turns off the interior lights.
 Turning the interior lights on or off.
Central po- sitionor
 a) The interior lights come on automati-
cally when you unl
ock the vehicle
,
open a door or r
emove the key from
the ignition.
The light goes out a few seconds after
closing all the doors, when locking the
vehicle or connecting the ignition.
* /
 Turning the reading light on and off a)
Depending on version.
Gl o
ve compar
tment and luggage com-
par

tment lighting*
When opening and closing the glove com-
partment on the front passenger side and the
rear lid, the respective light will automatically
switch on and off.
Footwell lighting*
The lights in the footwell area below the dash
(driver and front passenger sides) will switch
on when the doors are opened and will de-
crease in intensity while driving. This intensity
setting can be changed through the infotain-
ment system menu (key  > SETTINGS >
lIGHTING > Interior lighting

Operation
Regularly clean dirt that has become encrus-
t ed on the headlights, e
.g., remains of insects.
T o ensur
e the headlight washers work cor-
rectly in winter, clean away any snow that
may be present on the jet covers located on
the bumper. If necessary, remove ice with an
anti-ice spray. Note

Transport and practical equipment
LED on the power socket
Flashing green
light: The ignition is switched off, but
there is enough power av
ail
able
to continue supplying the socket
with current for a maximum of 10
minutes. If the connector is un-
plugged before this time elap-
ses, the socket is disconnected
and cannot be used again until
the ignition is switched on again.
Flashing red
light: There is an anomaly, e.g. dis-
connection due to a current
surge or o
v

erheating. Disconnection due to overheating
When the t
emper
atur
e e

xceeds a certain val-
ue, the 230 volt socket inverter is automati-
cally disconnected. The disconnection pre-
vents overheating when the power consump-
tion of the connected devices is excessive or
the ambient temperature is very high. The
230-volt power supply can be used once
again after a cooling time. First unplug the
connector of the connected device and then
plug it back in again. This prevents the elec-
trical device from being switched on again if
this is not wanted. WARNING
The electrical system is under high voltage!