navigation system Seat Leon 5D 2009 MEDIA SYSTEM 2.2

NAV (navigation system) function selection button
78
Note•If you miss a turn during route guidance and are unable to turn back, keep
on driving until the navigation system has calculated a new route for you
 .•The quality of the indications emitted by the equipment depends on the
available navigation data and, in case of traffic problems, traffic reports as
well. The traffic stations are responsible for the content and the quality of the
traffic reports.Stopping and resuming route guidance
Active route guidance can be stopped and later resumed at
any time.
Select a destination and start route guidance. During route guid-
ance, the map view is displayed by default.
– Briefly press the bottom-right or bottom-left area of the screen in the map view to display the function buttons fig. 69 .
– Press the function selection button to switch between the Navigation main menu and the map view.
– If you press the function button in either of the two menus, route guidance is stopped at the current position.
– To resume route guidance, switch to the map view and press the function button fig. 70 .
– Route guidance will be resumed from your current position.In the Navigation main menu, you have to select the most recent destination
from the Last destinations menu to resume an interrupted route guidance
 page 60.
Fig. 69 Stopping route
guidance.
Fig. 70 Route guidance
interrupted.
NAV
Stop
Start
media_system_ingles.book Seite 78 Donnerstag, 5. Februar 2009 3:31 15

NAV (navigation system) function selection button79
Pressing the function button in the map view always automatically
starts route guidance to the most recently used navigation destination.Information window, route list and excluding route sections
During route guidance, a route list can be displayed, which
shows the route sections ahead. Upcoming route sections
can be excluded manually.
If you press the button at the top right of the unit in one of the
navigation menus during active route guidance, the information
window will open fig. 71 .
Showing the route list
– Press the function button in the information window.
– The route list for the active route guidance will be calculated and displayed fig. 72 .
– The route list contains all roads names or designations and route sections along the route up to the next destination.
– It also displays the distance to be travelled along each road and the expected time required to reach the next turning point.
Manually excluding route sections
– It is possible to exclude one or more displayed route sections from the navigation route.
Start
Fig. 71 Information
window during route guid-
ance.
Fig. 72 Route list during
route guidance.
Route list
media_system_ingles.book Seite 79 Donnerstag, 5. Februar 2009 3:31 15

NAV (navigation system) function selection button
80
– Mark the first route section of the stretch of route you wish to exclude by turning the setting knob  page 3, fig. 1 .
– Press the function button. The symbol next to the item is marked as excluded and the function button changes to .
– Mark the final route section of the stretch of route you wish to exclude.
– Press the function button.
– The route will be recalculated and the function button changes to .
– Press in the information window to cancel an exclusion and include the route sections concerned in the route calculation
again.If you only wish to exclude part of a route section, proceed as described
below page 85, “Entering route exclusions (congestion ahead)”.
Excluded route sections and traffic congestion are displayed on the map
 page 81, “Representation of traffic congestion on the map”.
You can open the information window from any navigation menu except the
Navigation settings menu by pressing the button at the top right of the unit
 page 69.
During active route guidance, the final destination is displayed at the top of
the information window page 79, fig. 71 . If you have also entered a stop-
over destination, this will be displayed above the final destination
 page 73.
Dynamic route guidance with TMC (Traffic Message Channel)
During dynamic navigation, traffic information from the TMC
station is taken into consideration when planning the route.In the route options, you can determine whether TMC traffic reports
should be taken into account in the route calculation. Route options
can be altered even during a route guidance.
Switching dynamic navigation on and off
– Press the function selection button in one of the naviga-
tion menus.
–In the Navigation settings menu, press the func-
tion button.
–In the Route options menu, tick or untick the checkbox in the
function button fig. 73 .
A10
Exclude
Exclude to
Exclude to
Cancel
Cancel

Fig. 73 Specifying route
options.
SETUP
Route options
Dynamic route
media_system_ingles.book Seite 80 Donnerstag, 5. Februar 2009 3:31 15

NAV (navigation system) function selection button81
The current TMC traffic reports can be displayed in a listpage 84, “TRAF
function selection button”.
Representation of traffic congestion on the map
Traffic problems received via TMC that affect your route will be displayed on
the map with a colour symbol. Traffic congestion that is not on the route is
shown on the map by a grey symbol.
Generally understood symbols are used to indicate the type of traffic conges-
tion (e.g. an “overturned vehicle” for accident). The positioning of the TMC
symbol indicates which direction is affected by the congestion.
If there is reported congestion on the route, the affected route section is
coloured red. If the reported congestion is not on the route, the affected
section of road is coloured grey. If route guidance is not active, all traffic
congestion will be coloured grey.
Dynamic navigation
When dynamic navigation is switched on, you will be automatically diverted
during route guidance to avoid reported traffic congestion on your route if it
is calculated that the diversion will save time page 81, “Conditions for
dynamic navigation”.
Once a traffic report that is relevant for your route has been received, a
spoken announcement will be made to inform you that the route is being
recalculated to take traffic reports into account.
A similar announcement is also given if any traffic congestion that was taken
into account in the original route calculation has disappeared and it has now
become possible to take a more favourable route.
Conditions for dynamic navigation
TMC (Traffic Message Channel) is a digital radio data system for the constant
transmission of traffic reports.
The unit is constantly supplied with TMC traffic reports in the background,
provided that a TMC station can be received at the current location. The quality of the traffic reports sent depends on the radio station broad-
casting them. The reception of TMC traffic reports cannot be switched on or
off.
You do not have to listen to the TMC station.
The radio-navigation system can only process and store TMC traffic reports if
the unit has access to navigation data for the area you are currently travelling
through
page 49.
The current TMC traffic reports can be viewed by pressing the function
selection button page 84.
Note
•In some situations, you may find that a diversion based on the TMC infor-
mation does not save you time as the alternative route is also congested.•You can also exclude an upcoming section of the route manually if traffic
congestion ahead has not yet been recorded by TMC traffic reports
 page 79.
TRAF
media_system_ingles.book Seite 81 Donnerstag, 5. Februar 2009 3:31 15

NAV (navigation system) function selection button
82Other navigation settingsYou can open the Navigation settings menu from any navigation
menu by pressing the function selection button. Specifying route options
– Press the
function button.
– Define the options for route calculation in the next menu as described page 74.
Changing the announcement volume
– Press the function button. A settings
menu opens in which you can set the volume for navigation
announcements. If you turn the setting knob anti-clockwise all
the way (display: Off), no navigation announcements will be
given during route guidance page 76.
Day / night
– Press the function button and select the desired setting in the pop-up window.
– Press the function button for the map view to change between night and day design, depending on whether the head-
lights are switched on or off.
– Press the or function button to manually establish night or day design for the map screen.
Displaying points of interest as symbols on the map
– Tick the checkbox to display the points of interest (petrol stations/car parks) as symbols on the map.
Fig. 74 Navigation
settings menu.Fig. 75 Navigation
settings menu.
SETUP
Route optionsAnnouncement volumeDay/NightAutomaticDay
Night
See POIs
media_system_ingles.book Seite 82 Donnerstag, 5. Februar 2009 3:31 15

NAV (navigation system) function selection button83
Changing the time display
– Press the function button and press an option to
select or in the pop-up window. During route
guidance, the selected time information is shown in the map
view page 76, fig. 68 .
Defining or changing the home address
– Press the function button page 71,
“Storing or editing the home address”.
Starting a demonstration journey (Demo mode)
– To switch demo mode on or off, press the function
button to tick or untick the checkbox page 83, “Demo mode”.
– If demo mode is enabled, you can select a fictitious location when the vehicle is stationary by pressing the function button.
– After pressing , proceed as described
for “normal” entry of a destination page 58.
– If you have not selected a fictitious location, virtual route guid- ance will be started from the vehicle's last determined position.
– Once route guidance is activated, you must select by pressing it to start virtual route guidance.
Deleting the destination memory
– Press the function button and then
select whether to delete the entire destination memory or just
the last destinations list page 70. Setting the database for navigation
– Press the
function button to view informa-
tion on the data medium being used for navigation or to copy
data from a navigation CD onto a memory card page 49.
If the vehicle is moved and the unit can determine its current location by GPS
positioning, any manually entered location will be overwritten with the
current vehicle location.
Demo mode
In demo mode you may begin a virtual route guidance. The virtual route guid-
ance will be repeated upon reaching the fictitious destination. You can stop
virtual route guidance in the same way as “normal” route guidance. To start
a “real” route guidance, deactivate the demo mode or select when
starting route guidance.
If you selected a fictitious starting point for the virtual route guidance, it may
take a while for the unit to determine your real location again, depending on
the number of satellites currently available. The unit first has to reorient itself.
Drive a few yards.
Time displayETA
Travel time
Enter home address
Demo mode
Demo mode starting point
Demo mode starting point
Demo
Delete destination memory
Navigation database
Normal
media_system_ingles.book Seite 83 Donnerstag, 5. Februar 2009 3:31 15

TRAF function selection button85
Entering route exclusions (congestion ahead)
– To exclude part of the calculated route during route guidance, press the function button.
– Then enter the length of the stretch of route to be excluded by turning the setting knob (maximum 30 miles).
– Confirm the value by pressing .
– The route will be recalculated and the function
button changes to .
– Press in the list of current TMC traffic reports to cancel an exclusion and include the route section concerned in the route
calculation again.
During route guidance, you can also completely exclude the route sections
displayed in the route list  page 79.
Excluded route sections and traffic congestion are displayed on the map
 page 81, “Representation of traffic congestion on the map”.
Note
•The unit is constantly supplied with TMC traffic reports in the background,
provided that a TMC station can be received at the current location. The
station listened to does not have to be the TMC station.•The radio-navigation system can only process and store TMC traffic
reports if the unit has access to navigation data for the area you are currently
travelling through page 49.•The quality of the dynamic route guidance depends on the information
contained in the traffic reports. The radio stations broadcasting this informa-
tion are responsible for the content.•TMC traffic reports are required for dynamic navigation page 80.
•In some situations, you may find that a diversion based on the TMC infor-
mation does not save you time as the alternative route is also congested.
Cong. ahead
A10
OK
Cong. ahead
Cancel
Cancel
media_system_ingles.book Seite 85 Donnerstag, 5. Februar 2009 3:31 15

System settings87
Note
The system of units used in the navigation menu (metric or imperial) is deter-
mined by the instrument panel. Follow the instructions given in the vehicle
wallet to change the system on units on the instrument panel.
media_system_ingles.book Seite 87 Donnerstag, 5. Februar 2009 3:31 15

Index89
Index
AAddress entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
AM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
medium wave frequency band . . . . . . . . . . . 14
Anti-theft coding . . . . . . . . . . . . . . . . . . . . . . . . . 88
Audible navigation indications settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
AUX additional AUX-IN socket . . . . . . . . . . . . . . . 45
adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
AUX2 socket . . . . . . . . . . . . . . . . . . . . . . . . . . 45
AUX-IN socket . . . . . . . . . . . . . . . . . . . . . . . . 32
Connecting to an audio source . . . . . . . . . . . 32
input volume . . . . . . . . . . . . . . . . . . . . . . . . . 33
output volume . . . . . . . . . . . . . . . . . . . . . . . . 33
Avoiding congestion with TMC automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81BBalance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Bass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7CCar parkstart route guidance . . . . . . . . . . . . . . . . . . . 62 CD
CD-R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
CD-RW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Dual Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
DVD-Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Flip Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
CD Mode requirements . . . . . . . . . . . . . . . . . . . . . . . . . 25
CD mode CD text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
ejecting a CD . . . . . . . . . . . . . . . . . . . . . . . . . 29
inserting a CD . . . . . . . . . . . . . . . . . . . . . . . . 29
MP3 file requirements . . . . . . . . . . . . . . . . . . 26
MP3 playlist requirements . . . . . . . . . . . . . . 26
safety precautions . . . . . . . . . . . . . . . . . . . . . 45
CD player information for operating . . . . . . . . . . . . . . . 45
CD text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Checkboxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Cleaning a CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Climate control display screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Control elements . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Convenience radio coding . . . . . . . . . . . . . . . . . . 6
Coordinates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Cursor
entering characters . . . . . . . . . . . . . . . . . . . . 56
DData media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Demo modeNavigation . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Destination editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Destination address window . . . . . . . . . . . . . . . 59
Destination memory . . . . . . . . . . . . . . . . . . . . . . 65 deleting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Destination window . . . . . . . . . . . . . . . . . . . . . . . 59
Displaying altitude . . . . . . . . . . . . . . . . . . . . . . . 70
Driver assistance systems on-screen display . . . . . . . . . . . . . . . . . . . . . . 8
Dynamic navigation . . . . . . . . . . . . . . . . . . . . . . . 80EEntering a stopover destination . . . . . . . . . . . . . 73
Entering the PIN . . . . . . . . . . . . . . . . . . . . . . . . . . 88
EON (Enhanced Other Network) . . . . . . . . . . . . . 24
External audio source AUX-IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
media_system_ingles.book Seite 89 Donnerstag, 5. Februar 2009 3:31 15

Index
90external audio source
MEDIA-IN multimedia interface . . . . . . . . . . 41
External data medium iPod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
External media . . . . . . . . . . . . . . . . . . . . . . . . . . . 42FFader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
File formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Flagged destination renaming . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
FM very high frequency . . . . . . . . . . . . . . . . . . . . 14
Forward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Frequency band . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Frequency change . . . . . . . . . . . . . . . . . . . . . . . . 22
Function buttons . . . . . . . . . . . . . . . . . . . . . . . 7, 10
Function selection TRAFFIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Function selection buttons . . . . . . . . . . . . . . . 7, 10 general notes . . . . . . . . . . . . . . . . . . . . . . . . . 7
MEDIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
NAV, navigation . . . . . . . . . . . . . . . . . . . . . . . 47
RADIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
TRAF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
GGALA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
GPS status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70HHandlingbuttons and function buttons . . . . . . . . . . . . 7
control elements . . . . . . . . . . . . . . . . . . . . . . . 3IIgnition offswitch-off delay (Ti meout) . . . . . . . . . . . . . . . 6
Information kilometres . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
metric/imperial . . . . . . . . . . . . . . . . . . . . . . . 87
miles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Interference mobile telephone . . . . . . . . . . . . . . . . . . . . . . 5
Items scroll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10KKilometres/miles . . . . . . . . . . . . . . . . . . . . . . . . . 87LLaser, CD modesafety precautions . . . . . . . . . . . . . . . . . . . . 45 Last destinations
deleting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Lower sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
MMain menu NAV navigation . . . . . . . . . . . . . . . . . . . . . . . 52
RADIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
settings (SETUP) . . . . . . . . . . . . . . . . . . . . . . 86
MDI Description . . . . . . . . . . . . . . . . . . . . . . . . . . 41
equipment list . . . . . . . . . . . . . . . . . . . . . . . . 44
error messages . . . . . . . . . . . . . . . . . . . . . . . 44
iPod control . . . . . . . . . . . . . . . . . . . . . . . . . . 44
MEDIA-IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
multimedia interface . . . . . . . . . . . . . . . . . . . 41
operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
MEDIA AUX-IN socket . . . . . . . . . . . . . . . . . . . . . . . . 32
CD cannot be read . . . . . . . . . . . . . . . . . . . . . 26
CD mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
CD text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
changing playback mode . . . . . . . . . . . . . . . 38
changing the media source . . . . . . . . . . . . . 34
changing track . . . . . . . . . . . . . . . . . . . . . . . 36
copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
data medium cannot be read . . . . . . . . . . . . 26
Extras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
file formats . . . . . . . . . . . . . . . . . . . . . . . . . . 26
media_system_ingles.book Seite 90 Donnerstag, 5. Februar 2009 3:31 15