Wheel Seat Tarraco 2020 Owner's Guide

Driving
Automatic gearbox/DSG au-
t omatic gearbo
x*
Introduction Your vehicle is equipped with an electronical-
ly contr
oll

ed manual gearbox. Torque be-
tween the engine and the gearbox is trans-
mitted via two independent clutches. They
replace the torque converter found on con-
ventional automatic gearboxes and allow for
smooth, uninterrupted acceleration of the ve-
hicle.
The Tiptronic system allows the driver to
change gears manually ››› page 230,
Changing gear in Tiptronic mode*.
Control lamps 
It lights up green
The brake is not pressed.
T o sel

ect a gear range, press the brake pedal. 
Flashes green
The selector lever locking button is not engaged.
The v ehicl

e is prevented from moving forwards. En-
gage the selector lever lock. Selector lever positions
Fig. 166
Selector lever lock. Fig. 167
Selector lever lock (hybrid vehicles). The selector lever position is shown when the
corr
esponding sign lights up

. With the selec-
tor lever in the manual gearbox positions M, D
and S, the engaged gear is also shown on the
display. 
– Parking l
ock
When the lever is put in this position, the drive
wheels are locked. The lever must only be put
in P when the vehicle is stationary ››› .
T o put the l

ever in P or take it out of P , the
locking button must be pressed and held and
the brake pedal pressed simultaneously.
 – Reverse gear
Reverse gear must be engaged only when
the vehicle is stationary and the engine is
idling ››› .
T o mo

ve the lever to position R, the lock but-
ton must be pressed and held while pressing
the brake pedal at the same time. The reverse
lights come on when the lever is in the R posi-
tion with the ignition on.
 – Neutral
With the lever in this position, the gear is in
neutral.
Press the brake pedal to move the lever from
N to D/S when the vehicle is stationary or at
speeds below 3 km/h (2 mph) ››› .
 – P
ermanent f

orward drive position
The lever in the D/S position enables the
gears to be operated in normal mode (D) or
sport mode (S). To select Sport mode S,
move the lever backwards. Pushing the lever
again will select normal mode D. The
228

Driving
k
It lights up grey
Hill Descent Control is not active. The system is
s wit
ched on, but is not adjusting. Some control and warning lamps will light up
briefly when the ignition is s
wit

ched on to
check certain functions. They will switch off
after a few seconds. WARNING
Observe the safety warnings ››

› in Con-
tr ol and w
arning lamps on page 85. Description and operation
Hill Descent Control limits the speed on steep
descents by aut
omatically br

aking all four
wheels, both when moving forward and in re-
verse. As the anti-lock brake system remains
active, it prevents the wheels from locking. In
vehicles with manual transmission, the Hill
Descent Control adapts the theoretical
speed without slowing the engine below its
idling speed.
After starting the descent of a slope below
30 km/h (18 mph), speed is limited to a mini-
mum of 2 km/h (1 mph) and a maximum of
30 km/h (18 mph). When appropriate, the
driver may increase or decrease the speed
within the limit by pressing the accelerator or the brake. At this point the function is interrup-
ted and, if necessary, it is then r

eactivated.
Even so, it is imperative that the surface guar-
antees sufficient adhesion. For this reason,
the Hill Descent Control will not fulfil its func-
tion when, for example, descending a slope
with a frozen or slippery surface.
Hill Descent Control is available when the
dash panel display shows the message k .
Hill Descent Control automatically intervenes
if the following conditions are met:

Start and driving
sportier, more direct and noticeably more dy-
namic driving sensation.
St eering assist
This help assists the driv
er in critical situa-
tions. It recommends turning the steering
wheel to perform a corrective manoeuvre
(counter-steering), turning slightly to avoid
skidding ››› .
WARNING
Steering assist helps the driver in critical
sit uations. The driv

er is the person who has
to control the vehicle's steering at all times. Control lamp
v
It lights up red
Faulty steering.
Do not continue driving, st op the v

ehicle as soon as
possible and in a safe manner.
Take the vehicle to a specialised workshop and have
the fault repaired as soon as possible. v
It lights up yellow
Limited steering operation.
Driv e car

efully to a specialised workshop to have the
steering checked.
If the warning light does not come on again after re-
starting the engine and driving a short distance, it is
not necessary to check the steering.
OR: The 12-v olt batt
ery was disconnected and re-
connected.
Drive a short distance at 15-20 km / h (9-12 mph). v
It flashes yellow
The steering column is jammed.
When st opped, t

urn the steering wheel in both direc-
tions.
OR: The st eering column does not unlock or lock.
T
urn off the ignition and turn it on again. Consider the
messages shown on the instrument panel display.
Do not continue driving if the steering column re-
mains locked after switching on the ignition. Seek
specialist assistance. The control lamp should light up for a few
seconds when the ignition is s
wit

ched on. It
should go out once the engine is started. WARNING
Never ignore the warning lamps or messag-
es.

Start and driving
Changing tyres
On v ehicl
es with four-wheel drive, all four
tyres must have the same rolling circumfer-
ence. Also avoid using tyres with varying
tread depths ››› page 354
.
Off-roader?
Your SEAT vehicle is not an off-roader: it does
not have enough ground clearance to be
used as such. It is therefore best to avoid
rough tracks and uneven terrain as much as
possible. WARNING

Driving
Switching between the speed limiter and
GRA or ACC (whil e the speed limit
er is
connected)
To change between the driving assistance
systems, press button t ››› Fig. 181
2 , then
sel ect with the right thumb

wheel on the multi-
function steering wheel in the instrument
panel menu and press the thumbwheel to
confirm your selection.
It switches between the speed limiter and
cruise control (GRA) or the adaptive cruise
control (ACC).
Going down slopes with the speed limiter
If the programmed speed is exceeded while
driving downhill, after a short time the control
warning lamp

Driver assistance systems
ACC detects it and adapts the speed au-
t omatically, maint
aining a distance set by
the driver.
Does my vehicle have ACC?
Your vehicle has ACC if it has a configuration
menu in the infotainment system ››› page 90
and if it has the ACC function buttons on the
multifunction steering wheel ››› Fig. 185
.
Speed range
ACC regulates speeds between 30 km/h (20
mph) and 210 km/h (130 mph). 1)
If the vehicle is fitted with an automatic gear-
box, the ACC can bring the vehicle to a
standstill if a vehicle in front of it stops.
If your vehicle is fitted with a manual gearbox,
you must pay attention to speed and gear
changes. The ACC is deactivated if the
speed is too low (less than 30 km/h) of the
engine RPM is too low or high.
Driver intervention prompt ACC is subject to certain limitations in-
herent to the system. This means that
the driver will have to control the speed
and distance from other vehicles in cer-
tain situations. In this case, the instru-
 ment cluster display will tell you t
o in-
tervene by applying the brake, and an
audio warning will be played.
Radar sensors
The ACC uses the front radar technology.
Read its maintenance instructions and infor-
mation about its limitations ››› page 243
. WARNING
The ACC’s technology cannot overcome
the syst em's inher

ent limitations or change
the laws of physics. If used negligently or
involuntarily, it may cause serious acci-
dents and injuries. The system is not a re-
placement for driver awareness.

Driving
ACC operation Fig. 185
On the multifunction steering wheel:
butt ons t
o operate the ACC Connecting

Driving
Avoid undertaking on the right 1)
If a v ehicl
e is detected in the left lane that is
travelling at a speed slower than that set by
the driver, it will brake the vehicle within the
comfort limits of the system to avoid passing
it on the right ››› Fig. 187
.
You can cancel this regulation by changing
the set speed or by pressing the accelerator
pedal.
The function works at speeds over 80 km/h
(50 mph). It may not be available in certain
countries.
Overtaking
When the turn signal is switched on for over-
taking, the ACC reduces the distance from
the vehicle in front to help with the overtaking
manoeuvre. The set cruising speed will not be
exceeded.
The function works at speeds over 80 km/h
(50 mph). It may not be available in certain
countries.
Stop&Go function
 Valid for: vehicles with an automatic gearbox
The ACC can bring the vehicle to a standstill
(0 km/h) if the vehicle in front stops. The ACC remains active and the message
ACC ready to start is displayed on the in-
strument clust
er for a few seconds. You can
extend or reactivate this warning by pressing
the button  or, depending on your vehicle’s equipment, by grabbing the steering wheel.
During this time, the vehicle will move off
again if the vehicle in front moves forwards.
To move off when the message ACC ready
to start is not longer displayed, once the
vehicle in front has moved off:

Driver assistance systems
distance from the vehicle in front that is
pr esel
ected by the driver and remain in
the preferred position within the lane.
Travel Assist uses the same sensors as Adap-
tive Cruise Control (ACC) and Lane Assist.
Therefore, carefully read the information
about the ACC ››› page 254
and the Lane
Assist ››› page 262
and take into account the
limitations of the systems and the indications
given in the information.
Speed range
Travel Assist adjusts at speeds between ap-
prox. 30 km/h (approx. 20 mph) and approx.
210 km/h (approx. 130 mph); in the case of
the adaptive lane guidance function, be-
tween 0 km/h (0 mph) and approx. 250 km/h
(approx. 155 mph). This range may vary de-
pending on the market.
Driving with Travel Assist
Travel Assist automatically controls the ac-
celerator pedal, the brakes and the steering.
In addition, Travel Assist may, within its limita-
tions, decelerate the vehicle until it stops be-
hind another that stops and automatically
starts again.
You can override assisted adjustment at all
times. How to know if the vehicle is fitted with
Tr
avel Assist
The vehicle is fitted with Travel Assist if the
multifunction steering wheel has the button


Driving
Indications on the instrument panel
displ ay Fig. 191
On the instrument panel display: indi-
cation with activ e adjustment.Fig. 192
On the instrument panel display: con-
tr ol l
amps. Displays on the screen
› ›

› Fig. 191
The adaptive lane guidance function is
active.
1 Distance set.
In addition, depending on the equipment,
contr ol l

amps indicate the status of the sys-
tem on the instrument panel display:
››› Fig. 192
Travel Assist active, adaptive cruise con-
trol and adaptive lane guidance function
are active.
Travel Assist active, adaptive cruise con-
trol active and adaptive lane guidance
function passive.
Travel Assist active, adaptive cruise con-
trol passive and adaptive lane guidance
function active.
Travel Assist active, adaptive cruise con-
trol and adaptive lane guidance function
are passive.
Inactive Travel Assist.
Depending on the equipment, more details
may be displayed on the instrument cluster,
such as dashed lines or other vehicles on the
road. 2 A
B
C
D
E Operating Travel Assist
Fig. 193
Left side of the multifunction steering
wheel : butt

ons for operating Travel Assist. Connecting