display SEAT TOLEDO 2019 User Guide
Page 174 of 300
Infotainment System
Display: Meaning
A F o f f The tracking of alternative frequencies is
disabl
ed. Note
Page 176 of 300
Infotainment System
Messages and symbols on the Media main
menu Display: Meaning
A Displays information about the artist
name, album name and song titl
e (CD
t
ext , ID3 tag on compressed audio
files).
Audio CD: displays track information. If
no data is avail
able, it only displays
T r a c k and the number corresponding to
the position it occupies on the data stor-
age device.
B Album cover display: If there are various
cov
ers within the same f
older/album, the
system only displays one of them.
It prioritizes displaying the covers in the
following manner:
1. Cover embedded in the file(s).
2. Image in file folder.
3. Default icon of the connected device.
C The playing time so far and time remain-
ing in minutes and seconds. In the case
of audio fil
es with v
ariable bit rates (VBR)
the remaining time may vary.
T P a) The TP function is active and can be
used: sel
ect
R a d i o ! S e t t i n g s !
T r a f f i c p r o g r a m m e ( T P ) .
a) Ther
e are no traffic stations available:
select R a d i o ! S e t t i n g s ! T r a f -
f i c p r o g r a m m e ( T P ) . a)
Depends on the market and unit in question. Note
Page 180 of 300
Infotainment System
Function button: function
$ The image viewed was obtained via
GPS localisation and upon pr
essing
this function butt
on, the navigator
menu opens to start a route to this
destination.
/ Rotate the view of the image to the
left or the right.
j R
eset the vie
w of the image.
N To stop the playback of a slideshow.
The
N function button changes to
b .
b To continue the playback of a slide-
show
. The b function button
changes to N .
/
To change to the P R E V I O U S
or
N E X T image.
The same function can be per -
f
ormed by sliding your finger hori-
zont
ally across the screen.
S E T T I N G S Open the Image settings menu.Enlarging or reducing the view
T
o enl
ar
ge or reduce the view of the image
displayed:
Page 185 of 300
Operating modes
Destination.
... Estimated time of arrival at destina-
tion.
... Calculated distance to destination.
... Travelling time.
* ... Distance to the next stopover.
Press on the destination to display the function
butt ons.
Del
et
e destination.
To start guidance direct to the selec-
ted destination. Destinations that
come bef
or
e the selected destination
are ignored.
To open the detailed view of the desti-
nation in question.
Available function buttons.
New dest. To add a new destination to the tour.
Destina-
tions To add a new destination from M y
d e s t i n a t i o n s to the tour
.
Storing To store the created tour in the tour
memory.
Start To start route guidance.
Calculate To update calculated distance and es-
timated arrival time
.a) Stop
To stop route guidance to the active
destination.b)
c To move a stopover or a destination to
another position on the list. Press and
dr ag t
o move the destination. a)
This function button is only displayed with route
guidance activat ed and when a destination has been
added t
o the tour.
b) This function button is only displayed with route
guidance activated.
L
ast destinations
View of destinations for which a route has al-
ready been started.
My destinations
Page 186 of 300
Infotainment System
Points of interest (POI) Fig. 200
Points of interest on the map. The points of interest saved in the navigation
dat
a memory ar
e divided int
o different point
of interest categories. Each point of interest
category is assigned a symbol for display on
the map.
If a database of points of interest has been
imported into the Infotainment system,
Page 187 of 300
Operating modes
Split screen Fig. 201
Split screen displayed. The split screen
Page 191 of 300
Operating modes
Vehicle status
Pr ess the
V e h i c l e s t a t u s butt
on to access
information on the V e h i c l e s t a t u s mes-
sages and S t a r t - S t o p s y s t e m . The Vehicle
status messages are displayed, in addition to
being specified on the corresponding button.
Telephone General information Fig. 206
Related video The Telephone functions described below
can be used thr
ough the Inf
ot
ainment system
if there is a mobile telephone connected to it
via Bluetooth
Page 204 of 300
Driving
With the help of this system, the ABS is activa-
t ed mor
e quickly and mor
e efficiently.
The brake assist function is deactivated auto-
matically when the brake pedal is released.
Hill hold control (HHC)*
The HHC system makes it easier to start the
vehicle on hills. The system maintains the
brake pressure created by pressing down on
the brake pedal for 2 seconds after it has
been released. Your foot can be removed
from the brake pedal and you can use the
accelerator pedal and move away on a hill
without having to use the handbrake. The
brake pressure drops as the accelerator ped-
al is pressed. If the vehicle cannot be started,
it will start to move backwards after 2 sec-
onds.
The HHC is activated on gradients of over 5%,
if the driver door is closed. It only works for
starting on hills, moving both forward and in
reverse. It is not activated during start-up
down hill.
Control lamp
If the control lamp ! flashes, the ESC is working.
If the ! warning lamp illuminates on ignition,
the ESC system may have switched off due to
technical reasons. Turn off the ignition and
turn it on again. Upon switching on the igni-
tion again, if the warning lamp has switched off, this means the ESC is functioning correct-
ly again.
If the !
warning lamp is illuminat
ed there is a
fault in the ESC.
The informative display indicates:
F a u l t : e l e c t r o n i c s t a b i l i t y c o n -
t r o l ( E S C )
or F a u l t : t r a c t i o n c o n t r o l s y s t e m
( A S R )
Go to a technical service. Note
If the battery is disconnected and connec-
ted again, the yell o
w warning lamp !
lights up when the ignition is switched on.
This warning lamp must switch off after
covering a short distance. Anti-lock brake system (ABS)
The ABS system prevents the wheels locking
during br
aking. This helps the driv
er k
eep
control of the vehicle.
The driver is made aware of ABS assistance
by the pulsating of the brake pedal and a
characteristic noise.
Keep the brake pedal pressed down while the
ABS is working. The ABS will switch off when the brake pedal is released. Never brake in-
termittently whil
e the ABS is working!
Control lamp
If the warning lamp is illuminated, there is a fault in the ABS.
The informative display indicates:
A B S f a u l t
The brake system alone is operational in the
vehicle, without ABS.
Go to a technical service. WARNING
Page 205 of 300
Start and driving
If the control lamp ! fl ashes, the ASR is w
ork -
ing.
If the ! warning lamp illuminates on ignition, the TCS system may have switched off due to
technical reasons. Turn off the ignition and
turn it on again. Upon switching on the igni-
tion again, if the warning lamp has switched
off, this means the TCS is functioning correct-
ly again.
If the ! warning lamp remains illuminated,
there is a fault in the TCS.
The informative display indicates:
F a u l t : t r a c t i o n c o n t r o l s y s t e m
( A S R )
Go to a technical service.
Electronic differential lock If one of the wheels starts to skid, the EDL
br
ak
es that wheel, tr
ansmitting the driving
force to the other wheels. This increases vehi-
cle stability and improves driving stability.
To prevent the disc brake of the braking
wheel from overheating, the EDL cuts out au-
tomatically if subjected to excessive loads.
The vehicle will continue to function normally
without EDL. The EDL will switch on again au-
tomatically when the brake has cooled down. Manual gearbox
Changing gears Fig. 215
Gear shift diagram of a 5- or 6-speed
manual gearbo x Read the additional information carefully
Page 210 of 300
Driving
G e a r b o x : S y s t e m f a u l t ! Y o u m a y
c o n t i n u e d r i v i n g .
Hav e the f
ault corrected by a specialised
workshop without delay.
G e a r b o x : S y s t e m f a u l t ! Y o u c a n
c o n t i n u e d r i v i n g w i t h r e s t r i c -
t i o n s . R e v e r s e g e a r d i s a b l e d
Take the vehicle to a specialised workshop
and have the fault repaired without delay. G e a r b o x : S y s t e m f a u l t ! Y o u c a n
c o n t i n u e d r i v i n g i n D u n t i l
s w i t c h i n g o f f t h e e n g i n e
Stop the vehicle in a safe place well away
from moving traffic. Seek specialist assis-
tance. G e a r b o x : t o o h o t . A d a p t y o u r
d r i v i n g a c c o r d i n g l y
Continue driving at moderate speeds. When
the warning lamp switches off, you can con-
tinue driving in a normal manner. G e a r b o x : p r e s s t h e b r a k e a n d e n -
g a g e a g e a r a g a i n .
If the fault was caused by a gearbox with a
high temperature, this driver message will be
displayed when the gearbox has cooled
again. Gear-change indicator
Choosing the ideal gear Fig. 219
Instrument panel: gear-change indi-
cat or (manual gearbo x). A gear change will be recommended if the
gear you ar
e in is not the most economical
choice . If no gear
-change is recommended, it
means that you are already in the most eco-
nomical gear.
Vehicles with a manual gearbox
The following display symbols