headlamp SKODA CITIGO 2012 1.G Owner's Manual

Using the system
Cockpit
Overview
Electrical power window in the driver's door 26
Central locking system 23
Electric exterior mirror adjustment 36
Air outlet vents 52
Lever for the multifunction switch:
› Turn signal lights and main beam, headlight flasher 31
› Speed regulating system 63
Steering wheel:
› With horn
› With driver’s front airbag 83
Instrument cluster: Instruments and warning lights 8
Lever for the multifunction switch:
› Multifunction display 11
› Windscreen wiper and wash system 33
Regulator for left seat heating 39
Depending on equipment fitted:
› Operating controls for the heating 52
› Operating controls for the air conditioning system 53
Socket for the cradle for the multifunction device Move & Fun 72
Warning light for the deactivated front seat passenger airbag 86
Switch for hazard warning lights 31
Storage compartment on the front passenger side 48
Front passenger airbag 83
Air outlet vents 52
Light switch 29
Bonnet release lever 108
Regulator for headlamp beam adjustment for the headlights 30
Lever for adjusting the steering wheel 57
Ignition lock 581
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21 Radio
Button for
City Safe Drive system 66
Depending on equipment fitted:
› Gearshift lever (manual gearbox) 61
› Selector lever (automated gearbox) 70
Storage compartment 49
Regulator for right seat heating 39
Note
■ Cars with factory-fitted radio are supplied with separate instructions for operat-
ing such equipment. ■ The arrangement of the controls and switches and the location of some items
on right-hand drive models may differ from that shown in » Fig. 1. The symbols on
the controls and switches are the same as for left-hand drive models. Ð 22
23
24
25
26
7
Cockpit

›
Press the locking mechanism 1
and carefully open the cover in the direction of
the arrow.
› After the fuse has been replaced, fold the cover upwards in the opposite direc-
tion of the arrow so that it audibly latches.
Fuse assignment on the underside of the dash panel No. Power consumer
1 Telephone, radiator fan, instrument cluster, engine control unit
2 Diagnostic connection, AC compressor
3 Clutch pedal switch, brake pedal switch
4 Daytime running lights 5 Switch wiring harness
6 Headlamp beam adjustment, exterior mirror adjustment
7-8 Automated transmission 9 Airbag
10 Park Assist 11 Low beam
12 Rear fog light
13 Low beam
14 Rear window wiper 15 Light switch
16 Steering force assistance 17 Windscreen washer
18 Reverse light switch 19 Injection valves, coolant pump
20 ABS/ESP, switch wiring harness 21 Switch illumination, number plate light
22 Daytime running lights
23 Light switch
24-26 Switch wiring harness 27 Interior light
28 Diagnostic connector 29 Central control unit
30 Exterior mirror heater 31 Cooler fan, regulator valve, lambda probe No. Power consumer
32 Turn signal, brake light
33 Main beam
34 Instrument cluster, main beam 35 Not assigned
36 Cigarette lighter, 12-volt power socket 37 Air blower for heating and air conditioning
38 Radio 39 Panoramic sliding roof, horn
40 Engine control unit 41 Central locking system
42 Ignition module
43 Seat heaters
44 Fuel pump 45 Light switch
46 Rear window heater 47 Power windows - right
48 Horn 49 Windscreen wipers50 Fog lights 51 Power windows - left Ð
139
Fuses and light bulbs

B
- Low beam and main beam
C
- Parking and daytime running light
Changing the bulb for the front turn signal light
› Turn the bulb holder A
» Fig. 122anti-clockwise
up to the stop and remove.
› Push the faulty bulb into the holder, turn
in anti-clockwise up to the stop and
remove.
› Insert a new bulb into the socket and turn
clockwise to the stop.
› Insert the lamp holder with the new bulb into the headlamp and turn it
clock-
wise until it stops.
Replacing the bulb for low beam and main beam
› Remove the connector on the bulb B
» Fig. 122.
› Remove the rubber cover.
› Press the circlip D
in the direction of the headlamp and then unhook in the di-
rection of the arrow.
› Remove the light bulb and insert a new light bulb in such a way that the fixing
lugs of the light bulb socket fit into the recesses at the headlight.
Installation is carried out in the reverse order.
Replacing the bulb for the front parking light and daylight running light
› Turn the bulb holder C
» Fig. 122anti-clockwise
up to the stop and remove.
› Remove the faulty bulb from the socket.
› Insert a new bulb into the socket.
› Insert the lamp holder with the new bulb into the headlamp and turn it
clock-
wise until it stops. ÐChanging the light bulb for side repeater turn signal lights
Fig. 123
Right side: Replacing the bulb for the turn signal light First read and observe the introductory information and safety warn-
ings on page 141.
›
Push the side repeater turn signal light in the direction of the arrow 1
» Fig. 123.
› Prise the turn signal light from the body in the direction of the arrow 2
.
› Remove the bulb holder 3
in the direction of arrow.
› Remove the faulty bulb from the socket.
› Insert a new bulb into the socket.
› Replace the bulb holder.
› Set the side repeater turn signal light with the side facing the rear of the vehi-
cle in the body and lightly press it until the spring on the other side of the side
repeater turn signal light latches. Ð Changing light bulbs for fog lights
Fig. 124
Front wheel houe: Changing light bulbs for fog lights
First read and observe the introductory information and safety warn-
ings on page 141.
›
Unscrew the two attachment bolts on the wheel house trim with the screw-
driver » page 127 , Vehicle tool kit (arrows) » Fig. 124.
› Undo the expanding rivet A
»
Fig. 124
below on the wheel house trim with a
flat, dull object, such as a coin, remove.
› Fold the wheel house trim to the side, remove the connector 1
.
› Turn the lamp holder (bulb set- holder including bulb)
anti-clockwise
as far as
the stop, remove.
› Insert the lamp holder with the new bulb into the headlamp and turn it
clock-
wise as far as the stop; insert the connector until it latches securely.
› Fold the wheel house trim back.
£
ä
ä
142 Do-it-yourself