SKODA OCTAVIA TOUR 2011 2.G / (1Z) User Guide

The brief instruction
10
The brief instructionBasic functions and important informationIntroduction
The chapter of the brief instruction is only used as a quick reference
of the most important operating elements of the vehicle. It is neces-
sary to observe all the information which is contained in the
following chapters of the Owner's Manual.Unlocking and locking the vehicle Unlocking the vehicle
Unlocking the boot lid
Locking the vehicle
Folding out/folding up of the key bit
Further information page 35, “Unlocking and locking the vehicle”.
Setting steering wheel positionFig. 3 Adjustable steering wheel: Lever on the steering column/the correct distance of the
driver from the steering wheelYou can set the height and the forward/back position of the steering wheel to any
desired position.
– Pull the lever below the steering column down fig. 3 - left.
– Set the steering wheel to the desired position (concerning height and forward/back position).
– Push the lever upwards as far as the stop.
Further information page 73, “Setting steering wheel position”.
WARNING
•
Adjust the steering wheel so that the distance between the steering wheel
and your chest is at least 25 cm fig. 3 - right. Not maintaining this minimum
distance will mean that the airbag system will not be able to properly protect
you - hazard!
•
Only adjust the steering wheel when th e car is stationary - danger of acci-
dent!
•
For safety reasons the lever must always be firmly pushed up to avoid the
steering wheel altering its position unintentionally when driving - risk of
accident!
Fig. 2 Remote control key
A1A2A3A4s2lk.2.book Page 10 Monday, April 18, 2011 7:41 AM

The brief instruction11
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Seat belt height adjuster– Move the height adjuster in the desired direction up or down fig. 4 .
– Then pull firmly on the belt to ensure that the seat belt height adjuster has
correctly locked in place.
Further information page 87, “Seat belt height adjuster”.
WARNING
Adjust the height of the belt in such a wa y that the shoulder part of the belt is
positioned approximately across the midd le of your shoulder - on no account
across your neck!Adjusting the front seats Adjusting a seat in a forward/back direction Adjusting height of seat*
Adjust the angle of the seat backrest
Adjusting lumbar support*
Further information  page 49, “Adjusting the front seats”.
WARNING
Only adjust the driver seat when the vehicle is stationary - risk of injury!Electric exterior mirror adjustment*Further information page 48, “Exterior mirror”.
Fig. 4 Front seat: Seat belt height
adjusterFig. 5 Controls at seat
A1

Heating of the external mirror

Adjusting left and right exterior mirrors simultaneously

Adjusting the right-hand exterior mirror

Switching off operating control
A2A3A4
Fig. 6 Inner part of door: Rotary knob
s2lk.2.book Page 11 Monday, April 18, 2011 7:41 AM

The brief instruction
12
Switching lights on and offFurther information page 40, “Switching lights on and off ”.Turn signal and main beam lever
Turn signal light right
Turn signal light left
Switching over between low beam and main beam lights
Headlight flasher
Further information page 42, “The turn signal   and main beam lever ”.Windscreen wiper lever Intermittent switch
Wipers off
Intermittent wipe
Slow wipe
Fast wipe
one time wipe
Automatic wipe/wash
Rear window wiper* Intermittent wipe - every 6 seconds
The automatic wiper/washer system
Further information page 45, “Windshield wiper”.

Switching off all lights/daylight driving lights*

Switching on side lights

Switching on the low beam and main beam

Fog lights*

Rear fog light
Fig. 7 Dash panel: Light switchFig. 8 Turn signal and main beam lever
AAABACAD
Fig. 9 Windscreen wiper lever
AAA0A1A2A3A4A5A6A7
s2lk.2.book Page 12 Monday, April 18, 2011 7:41 AM

The brief instruction13
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Power windows* Button for the power window in the driver's door
Button for the power window in the front passenger's door
Button for the power window at the rear right door
Button for the power window at the rear left door
Safety pushbutton for deactivating the power window buttons at the rear doors
Further information page 37, “Power windows*”.RefuellingFig. 11 Right rear side of the vehicle: Open fuel filler flap/fuel filler flap with cap unscrewed– To open the fuel filler flap, press  fig. 11 in the direction of arrow.
– Release the cap by unlocking it by turning the vehicle key to the left. – Unscrew the fuel filler cap anti-clockwise and place the fuel filler cap from above
on the fuel filler flap fig. 11 - right.
Further information  page 128, “Refuelling”.
Bonnet remote release– Pull the unlocking lever below the dash panel on the driver's side fig. 12 .Opening the bonnetFig. 13 Radiator grille: Release lever/ securing the bonnet with the bonnet support– Pulling on the release lever in direction of arrow fig. 13 will unlock the
bonnet.
– Take the bonnet support out of its holder and set it in the opening on the bonnet.
Fig. 10 Buttons on the driver's door
AAABACADAS
A1
Fig. 12 Bonnet release lever
A1
A2
s2lk.2.book Page 13 Monday, April 18, 2011 7:41 AM

The brief instruction
14
Further information page 130, “Opening and closing the bonnet.”.Inspecting the engine oil level Engine oil must not be refilled.
Engine oil can be refilled.
Engine oil must be refilled.
Further information page 132, “Check engine oil level”.
Fig. 14 Dipstick
AAABACs2lk.2.book Page 14 Monday, April 18, 2011 7:41 AM

Instruments and Indicator/Warning Lights15
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Instruments and Indicator/Warning LightsOverview of the instrument cluster
Engine revolutions counter page 15
Speedometer page 16
Engine coolant temperature display page 16
Display
− with counter for distance driven page 16
− with Service Interval Display  page 17
− with digital clock page 17
− with Multi-functional indicator* page 18
Button for the selection of the mode (t urn button)/the setting (press button):
− Set hours/minutes
− Activating/deactivating the second speed in mph or km/h*
− Service interval - Display of the remaining number of days, kilometres or
miles to the next Inspection Service/Reset*
1)
−Reset trip counter for distance driven −
Resetting Service Interval Display
− Activate/deactivate display mode
Fuel gauge page 16
Engine revolutions counterThe red zone in the revolutions counter fig. 15 indicates the maximum permis-
sible engine speed for all gears for an engine which has been run in and operating
at a normal temperature. Before reaching th e red zone of the rev counter scale, shift
up into the next higher gear. The engine control unit restricts the engine speed to
a steady limit value.
Before reaching the red zone of the rev coun ter scale, shift up into the next higher
gear.
Avoid high engine speeds during the driving time and before the engine has
reached operating temperature page 111.
Fig. 15 Instrument cluster
1)Valid for countries where the values are indicated in British measuring units.A1A2A3A4A5
A6
A1
s2lk.2.book Page 15 Monday, April 18, 2011 7:41 AM

Instruments and Indicator/Warning Lights
16For the sake of the environment
Shifting up early helps you save fuel and reduce the operating noise of your
vehicle.SpeedometerThe speedometer shows the current speed of the car.Engine coolant temperature DisplayThe coolant temperature gauge page 15, fig. 15 operates only when the igni-
tion is switched on.
In order to avoid any damage to the engine, please pay attention to the following
notes regarding the temperature ranges:
Cold range
If the pointer is in the left-hand area of the scale it means that the engine has not
yet reached its operating temperature. Avoid running at high engine speeds, at full
throttle and at severe engine loads.
The operating range
The engine has reached its operating temp erature as soon as the pointer moves
into the mid-range of the scale. The pointer may also move further to the right at
high engine loads and high outside temperat ures. This is not critical provided the
warning symbol
 in the instrument cluster does not flash.
If the symbol
 in the instrument cluster flashes it means that either the coolant
temperature is too high or the coolant level is too low. Observe the guidelines
 page 25, “Coolant temperature/coolant level ”.
WARNING
Pay attention to the warning notes page 131, “Working in the engine compart-
ment” before opening the bonnet and inspecting the coolant level.
Caution
Additional headlights and other attached components in front of the fresh air inlet
impair the cooling efficiency of the coolant. There is then a risk of the engine over-
heating at high outside temperatures and high engine loads!
Fuel gaugeThe fuel gauge page 15, fig. 15 only works when the ig nition is switched on.
The fuel tank has a capacity of ab out 55 litres. The warning symbol
 in the instru-
ment cluster lights up when the pointer reaches the reserve marking. There are
now about 9 litres of fuel remaining in the tank. This symbol is a reminder for you,
that you must refuel .
An acoustic signal sounds as an additional reminder.
Caution
Never run the fuel tank completely empty! The irregular supply of the fuel system
can lead to irregular running of the engine. Unburnt fuel may get into the exhaust
system and damage the catalytic converter.Counter for distance drivenThe distance which you have driven with yo ur vehicle is shown in kilometres (km).
In some countries the measuring unit “mile” is used.
Reset button
Hold the reset button page 15, fig. 15 pressed for approx. 1 second. The trip
counter is reset to zero.
Trip counter for distance driven
The trip counter shows the distance driven since the time the trip counter was last
erased. The trip is shown in steps of 100 metres or 1/10 of a mile.
Odometer
The odometer indicates the total distance in kilometres or miles which the vehicle
has been driven.
Fault display
If there is a fault in the instrument cluster Error will appear in the display. Contact a
specialist garage.
WARNING
Never seek to adjust the trip counter fo r distance driven while driving for safety
reasons!
A3
A6
A5
s2lk.2.book Page 16 Monday, April 18, 2011 7:41 AM

Instruments and Indicator/Warning Lights17
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Note
If the display of the second speed is activated in mph or km/h, this speed is shown
instead of the odometer on the display.Service Interval DisplayService Interval Display
Before the next service interval a key symbol

and the remaining kilometres are
indicated after switching on the ignition fig. 16 . At the same time, a display
appears regarding the remaining days until the next service interval.
The kilometre indicator or the days indicator reduces in steps of 100 km. or days
until the service due date is reached.
A flashing key symbol

and the text Service appears in the display for 20 seconds
as soon as the due date for the service is reached.
Resetting Service Interval Display
It is only possible to reset the Service In terval Display, if a service message or at
least a pre-warning is shown on the display of the instrument cluster.
We recommend having this resetting performed by a specialist garage.
The specialist garage:
•
resets the memory of the display after the appropriate inspection,
•
makes an entry in the Service schedule,
•
affix the sticker with the entry of the follo wing service interval to the side of the
dash panel on the driver's side.
This can be reset as follows: Press the button page 15, fig. 15 and keep it
pressed down, start the ignition, release the button and turn it to the left or right.
Caution
We recommend you ask a specialist garage to reset the service interval display.
Incorrectly setting the service interval display can cause problems to the vehicle.
Note
•
Never reset the display between service intervals otherwise this may result in
incorrect readouts.
•
information is retained in the Service Interval Display also after the battery of
the vehicle is disconnected.
•
The service interval display will need to be re-configured if the instrument
cluster is replaced. Contact a specialist garage. This work is carried out by a
specialist garage.
•
The data displayed is the same after rese tting the display with flexible service
intervals (QG1) using the reset button as th at for a vehicle with fixed service inter-
vals (QG2). We therefore recommend having the Service Interval Display reset only
by an authorised Škoda Service Partner who is familiar with the procedure for reset-
ting the display with a vehicle system tester.
•
Please refer to the brochure Service schedule for extensive information about
the service intervals.
Digital clockYou can set the time with the rotary knob page 15, fig. 15 .
Select the information which you wish to change by turning the button and carry
out the change of the selected information by pressing the button.
WARNING
The clock should not be adjusted while dr iving for safety reasons but only when
the vehicle is stationary!
Fig. 16 Service Interval Display: NoteA5
A5
A5
s2lk.2.book Page 17 Monday, April 18, 2011 7:41 AM

Instruments and Indicator/Warning Lights
18
Recommended gear*An information for the selected gear fig. 17 is shown in the display of the
instrument cluster.
In order to minimise the fuel consumpt ion, a recommendation for shifting into
another gear is indicated in the display.
If the control unit recognises that it is appropriate to change the gear, an arrow
is shown in the display. The arrow points upwards or downwards depending on
whether it is recommended to switch to a higher or lower gear.
At the same time, the recommended gear is indicated instead of the currently
selected gear .Multi-functional indicator (onboard computer)*IntroductionThis data from the multi-functional indicator appears in the display fig. 18 .
The multi-functional indicator offers you a range of useful information.
Note
In certain national versions the displays appear in the Imperial system of
measures.MemoryThe multi-functional indicator is equi pped with two automatic memories. The
selected memory is displayed in the middle of the display field fig. 18 .
The data of the single-trip memory (memory 1) is shown if a 1 appears in the display.
A 2 shown in the display means that data relates to the total distance memory
(memory 2).
Switching over the memory takes place with the button page 19, fig. 19 on the
windshield wiper lever.
Single-trip memory (memory 1)
The single-trip memory collates the drivin g information from the moment the igni-
tion is switched on until it is switched off. New data will also flow into the calcula-
tion of the current driving information if the trip is continued within 2 hours after
switching off the ignition. The memory will be is automatically erased, on the other
hand, if the trip is interrupted for more than 2 hours.
The outside temperature
page 19
Driving time
page 19
Current fuel consumption
page 20
Average fuel consumption
page 20
Range
page 20
Fig. 17 Recommended gear
AA
AB
AA
Distance driven
page 20
Average speed
page 20
Current speed*
page 20
Warning against excessive speeds*
page 20
Fig. 18 Multi-functional indicator
AB
s2lk.2.book Page 18 Monday, April 18, 2011 7:41 AM

Instruments and Indicator/Warning Lights19
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Total-trip memory (memory 2)
The total distance driven memory gathers da
ta from any number of individual jour-
neys up to a total of 19 hours and 59 minutes driving or 1.999 kilometres driven. The
memory is deleted when either of these limits is reached and the calculation starts
from anew.
The total-trip memory will no t, contrary to the single-trip memory, be deleted after
a period of interruption of driving of 2 hours.
Note
All information in the memory 1 and 2 is erased if the battery of the vehicle is
disconnected.Operating with the buttons on the windshield wiper leverThe rocker and the button are located in the grip of the window wiper lever
 fig. 19 .Selecting the memory– Tapping the rocker on the windshield wiper lever allows you to select the
desired memory.Selecting the functions– Press the rocker up or down. In this way, call up in sequence the individual
functions of the multi-functional indicator.Setting function to zero– Select the memory you want. –Press button .
The following readouts of the selected memory will be
set to zero by button :
•
average fuel consumption,
•
distance driven,
•
average speed,
•
Driving time.
You can only operate the multi-functional indicator when the ignition is switched
on. After the ignition is switched on, the function displayed is the one which you last
selected before switching off the ignition.
Outside temperatureThe outside temperature appears in the display when the ignition is switched on.
If the outside temperature drops below +4 °C, a snow flake symbol (warning signal
for ice on the road) appears before the te mperature indicator and a warning signal
sounds. After pressing the rocker on the windshield wiper lever fig. 19 , the
function which was shown last is indicated.
WARNING
Do not only rely upon the information given on the outside temperature display
that there is no ice on the road. Please note that black ice may also be present
on the road surface even at temperatures around +4 °C - warning, drive with
care!Driving timeThe driving time which has elapsed since the memory was last erased, appears in
the display. If you wish to measure the driv ing time as of a particular time, you must
set the memory to zero at this moment in time by pressing the button fig. 19
on the windshield wiper lever for longer than 1 second.
The maximum distance indicated in both me mories is 19 hours and 59 minutes. The
indicator is set back to null if this period is exceeded.
Fig. 19 Multi-functional indicator:
Control elements
A
B
BA
B
B
A
B
s2lk.2.book Page 19 Monday, April 18, 2011 7:41 AM