display SKODA SUPERB 2009 2.G / (B6/3T) Columbus Navigation System Manual

Range selector key SETUP
14 Acoustic feedback– Press on the function key behind and select a setting in the pop-
up window.
– Press or to switch the tone for confirmation of a function key operation
on the touch-screen on or off.
Display off– Pressing the function key makes it possible to set the touch-
screen to energy save mode, the display
is black and the current information about
the audio source is only displayed in the lower part.
– The display can be switched on again by
touching the touch-screen or by pressing
any button, except the control button.Note
Please note that manual adjustment of the
display in unfavourable conditions can lead
to the displays in the touch-screen
no longer being clearly visible.
Setup MapCall up the menu
Setup Map
by pressing the range selector key and the func-
tion key . Position of the split-screen Intended for positioning the split-screen in the map display. Aiming symbol Shows the destinations in 2D or 3D. Select displayable map details Press to select a map detail which is to be displayed. Selected map details are indicated by a tick in the check box
= and at the bottom in the entry line.
Display favourite symbol If the check-box is activated
=, the destinations stored as favourite destination will be
displayed in the map with the symbol of the selected favourite destination.
Setting the speed limit If the check-box is activated
=, the current speed limit on the driven stretch of the
road is shown in the display.Setup NavigationCall up the menu
Setup Navigation
by pressing the range selector key and the
function key . You can select the following functions:•
- three alternative routes are suggested;
•
- Setting of the navigation announcements;
•
- during route guidance, either the arrival time or the driving time is
shown in the map display;•
- Enter home address;
•
- activation of the demo mode and entry of the
average rate for the time calculation. Demo Mode A virtual route guidance can be
started in the demo mode. Virtual route guidance will
be repeated when reaching the fictive travel destination.
Acoustic feedback
On
Off
Switch off display
SETUP
Map
Split-screen
Select map details
Fig. 6 Menu: Setup Navigation
SETUP
Media
Suggest 3 alternative routesNav. announcementsTime displayDefine home addressAdvanced navigation settings
s32k.a.book Page 14 Friday, September 18, 2009 1:54 PM

Range selector key SETUP
15
As in this case the unit must first reorient itself it can take some time, depending on the number of the currently tracked satellites, unt
il the unit has again found the real loca-
tion. Drive a short distance. Nav. announcements
- no spoken driving recommendations will be provided.
- spoken driving recommendations are only provided when you have left the
calculated route, for example on the basis
of announced traffic pr
oblems. This setting
is recommended if audible drive recommendat
ions are normally no longer needed for
a daily driven route and navigation is only
used as dynamic naviga
tion. If an audible
driving recommendation is transmitted again on the basis of a change in route, navi- gation announcements must be
switched on again (Display:
).
- spoken driving recommendations will
be transmitted in the running audio
mode. Adjustable average speed Depending on the set average speed, the unit will determine an arrival or driving time during a route calculation and disp
lay it depending on the set-up.
Setup traffic programmeCall up the menu
Setup traffic programme
by pressing the range selector key
and the function key . Selecting preferred TMC station Press on if you wish your unit to automatically search for a TMC station. Select displayable announcements Press if, during route guidance, only
the TMC traffic announcements relating
to the traffic problems along your rout
e should be dislayed. If you press on
, all current TMC traffic announcements are displayed.
Switching the traffic announcements on or off A tick in the check box
= indicates that the traffic programme function is already
switched on.
Setting voice controlCall up the
Setup Voice Control
menu by pressing the range selector key and
the function key .Dialogue style– Select - the system gives the whole message without shortening it or
select - the system shortens some of the messages or replaces them by an audible signal
(gong), thus the operation of the system is accelerated.
Help display– The selected help display shows a range of the most important possible
commands in a pop-up window
Possible commands are
:
Delete voice recordings– Deletes the stored voice recordings for individual menu points.Setup VideoCall up the menu
Setup Video
by pressing the range selector key and the func-
tion key .Changing voice response– Press the function key , or in the menu
Setup Video
and select the desired language in the pop-up window.
– Pressing will fully switch off the display of sub-titles.Changing the aspect ratio of the touch-screen display– The currently set aspect ratio is
visible behind th
e function key .
– Press on the function key and on or in the pop-up window.
All video data will now be repl
ayed in the set aspect ratio.
Set-ups for vehicles with TV tuner If a TV tuner is connected to the unit, you
will find here furthe
r set-up possibilities.
OffDynamicNav. announcements
bOn
On
SETUP
Tra f f i c i n f o
Preferred TMC station
Automatic
Message display
On route
All announcements
traffic announcements
SETUP
voice control
long dialogueshort dialogue
SETUP
Video
Audio language
Menu language
Subtitles
Off
DVD-Format
DVD format
4:3
16:9
s32k.a.book Page 15 Friday, September 18, 2009 1:54 PM

Range selector key RADIO
16Range selector key RADIORadio modeSelect radio stationAll radio stations with strong reception are au
tomatically stored in
the list of stations.
The list of stations is automatically updated on a regular basis.Call up main menu RADIO and choose frequency range– Press the range selector key to call up the
RADIO
main menu. The currently
heard radio station is indicated at the top of the touch-screen.
– Press the range selector key to change the frequency range. Alternatively,
press on the function key in the main menu
RADIO
and on or in the
pop-up window. The current frequency range is indicated on the top left on the display.
Changing radio station– When pressing the arrow keys
on the unit or the arrow keys on the touch-screen
of the main menu
RADIO
⇒fig. 7
, you change to the previous or following station.
Select a radio station from the station list– Press the function key to display all radio stations that can currently be
received.
Scan function– Press the set button on the bottom right of unit to start the
automatic play
for
the current frequency range. All radio stat
ions with strong reception are automati-
cally played for approximat
ely five seconds according to the sequence in the
station list.
– Alternatively, press on the function key and press on in the pop-up
window.
– Press the set button or function key again to end the automatic play of
the currently heard radio station.
Manual station finding– Turn the set button , to adjust a radio st
ation manually via it
s station frequency.
The scale of the selected frequency range is inserted in the frequency band in the lower part of the touch-screen.
– Briefly press the set button to terminat
e the manual frequency selection and to
display once again the function keys.Note
•
If “ memory
” appears at the top left of the displa
y, you can only change over to the
stations stored in the preset list with the help of the arrow keys.Save radio stationSave a radio station on a displayed station key– Continue to press one of the six station keys to displayed in the
RADIO

main menu until a signal tone sounds. The currently heard radio station is then stored on this station key.
Fig. 7 Main menu RADIO
RADIORADIOBand
FM
AM
A3
Station list
A8
Extras
Scan
A8
b Scan
A8
1 ...
6 ...
s32k.a.book Page 16 Friday, September 18, 2009 1:54 PM

Range selector key RADIO
17
Save radio station– Press on the function key
while in the main menu
Radio
⇒page 16, fig. 7
.
A pop-up window with a range of
memory space groups is opened.
– When you select a memory space group,
a menu for saving six radio stations is
opened.
– Select a memory space and save the stat
ion by pressing on the memory space.
– If a memory space is selected, which already holds a radio station, it will be
overwritten.
Calling up a saved radio stationIf the currently heard radio station is already saved in the preset list, the memory space number is displayed behi
nd the description of the frequency range (
FM
or AM
).
Calling up a station via the station keys– Briefly press on one of the six station keys to displayed in the main menu
RADIO
until a signal tone sounds.
Select stations from the preset list– In the pop-up window, select the station
keys to be displayed in the main menu
RADIO
.
– Press the display of the desired station in the preset list.RDS functionRDS (“
Radio
Data
System”) serves to transmit progra
m identification and additional
services therefore also enabling automatic tracking of stations. In the event of sufficiently satisfactory reception, the suitable RDS radio stations will display the station name instead of the station frequency. If a radio station sends additional informat
ion via the RDS function while a station is
being stored, it can occur that the name of
the radio station is later displayed incor-
rectly in the preset list.
Change station name You can manually adap
t the station name.
Choose the stored radio station and wait until the correct name is displayed on the touch-screen. Continue to press on the disp
lay of the station name between the arrow
keys until “
Station name stored
” is displayed.
Traffic programme function TPSwitching traffic programme TP (TMC Program) on or off– Press the range selector key to call up the
RADIO
main menu.
– Press the function key . – Briefly press on in the opening pop-up
window to switch the traffic programme
function on or off.
The display “
TP” in combination with a station name (e.g. in the station or preset list),
indicates a traffic programme station. Irrespective of which radio station is heard,
an additional receiver part in the unit
ensures that a traffic programme station can al
ways be received as
long as the traffic
programme function is switched on. The functionality of the tr
affic programme function “
TP” is displayed at the top right on
the touch-screen. If no traffic programme station can be rece
ived because, for example, radio reception
is interrupted in general, “
No TP
” will be displayed instead of “
TP”. Remember that car
parks, tunnels, high building
s or mountains can interrupt
the radio signal up to the
total loss of reception. Incoming traffic announcement If you wish to interrupt the transmission
of the traffic announcement, press on the
function key in the pop-up window
Traffic announcement
. The traffic
programme function remains available and
a following traffic announcement is made
again while the audio mode is in oper
ation. Pressing the function key
will switch off the traffic programme function permanently.
memory
1 ...
6 ...
RADIO
Extras
TP
Cancel
TP deactivated
s32k.a.book Page 17 Friday, September 18, 2009 1:54 PM

Range selector key RADIO
18Display offDisplay off– Pressing the function key makes it possible to set the touch-
screen to energy save mode, the display
is black and the current information about
the audio source is only displayed in the lower part.
– The display can be switched on again by
touching the touch-screen or by pressing
any button, except the control button.
Switch off display
s32k.a.book Page 18 Friday, September 18, 2009 1:54 PM

Range selector key TRAFFIC (TMC)
19
Range selector key TRAFFIC (TMC)Displaying traffic reports TRAFFIC (TMC)TMC traffic reports are used
during route guidance, depend
ing on the set-up for the
automatic optimization of the route,
to report possible traffic problems.
– Press on the range selector key to display the current traffic reports in a list.– Press on the display of a traffic repo
rt to show it in a detailed display.
– You can browse through all the traffic information received in the detailed display,
also in sequence by using the arrow keys.
From which TMC station the reports are to
be announced can be determined in the
Setup Radio
.
During route guidance all set-up dependin
g TMC traffic reports are displayed in the
surrounding area of the location or only th
ose specified on the calculated route list.
Traffic problems are illustrated in the de
tailed display and in the map by a corre-
sponding symbol. The direction, in which a tr
affic problem is found in the map will be
displayed by an arrow in the symbol. In the event of a traffic problem an alternat
ive route can also be
calculated manually.
Note
•
The unit has a continuous background of
TMC traffic reports providing a TMC
station at the current location can be receiv
ed. The station you are listening to does not
have to be a TMC station.•
TMC traffic reports can only be evaluated
and displayed by the
unit if the naviga-
tion data for the currently driven area is stored in the unit memory or can be called up via an inserted navigation DVD.•
The quality of the dynamic route guidan
ce depends on the transmitted traffic
announcements. The radio stations broadcasti
ng this information are responsible for
the content.•
TMC traffic reports are necessar
y for the dynamic navigation.
•
There may not be any advantage in avoiding the traffic jam if, as a result of the TMC
traffic reports, the diversio
n is also heavily congested.
TMC
s32k.a.book Page 19 Friday, September 18, 2009 1:54 PM

Range selector key MEDIA
20Range selector key MEDIAGeneral information for CD/DVD operationAudio-CDs (CD-A) and Audio-DVDs, MP3-CDs and MP3-DVDs as well as Video-DVDs can be played in the internal CD/DVD drive. CD not legible If the unit cannot read
an inserted CD/DVD, “
CD fault will be displayed for a short
period of time. Please check CD.
” or “
Wrong data format. Data cannot be read.
”
and the CD/DVD is reinserted into the initial position after a few seconds. If the CD/DVD is not taken out within 10 seconds, it is drawn in again for safety reasons.
WARNING
•
The CD player is a 1st class laser product. There is a definite risk of injury
from invisible laser beams if it is opened.•
The CD player contains no parts that ha
ve to be serviced or repaired. Please
contact your specialist garage if a mechan
ica l d e fe c t o ccurs o r t he CD pl a ye r ha s
to be repaired.
Caution
•
Inserting a second CD/DVD while a CD/D
VD is being ejected can destroy the
CD/DVD drive in the unit. Please note that the CD/DVD ejection lasts a few seconds after pressing the
Eject key
. During this time the lock in front of the CD/DVD case
is open. It is essential that you wait until
the CD/DVD has been fully ejected before you
try to insert a new CD/DVD.•
If the CD/DVD drive becomes mechanically defective or a CD/DVD has been
inserted incorrectly or not fully, first of all “
CD fault will be displayed on the touch-
screen. Please check CD.
” and then the “
DVD drive fault
” indicated on the touch-
screen. Please check the CD/DVD and place it again correctly and fully into the drive. If a “ DVD drive fault
” is indicated again,
please contact your Škoda Service Partner.
•
If the inside temperature of the unit is t
oo high, no CDs or DVDs will be accepted.
The unit switches into the last active operating mode.
Note
•
If the function key is inactive, no ne
w Audio CD/DVD has been inserted or an
inserted Audio CD/DVD is not readable.•
It is possible that CDs/DVDs protected
by copyright and non-original CD-R, CD-
RW and DVD-RWs are not returned at all or only in certain circumstances.•
WMA audio data (Windows Media Audio) can also be replayed by the unit and
stored on the hard disk (HDD) providing
this has not been protected by the DRM
procedure copyright (Digital Rights Manage
ment). The operation and behaviour of the
unit complies with the MP3
compressed audio data and are not described further.
•
Please observe the following information for the MP3 operation
⇒page 24.
•
Please comply with the national legal
copyright requirements in your country.
•
The DVD drive installed into this unit uses a Dolby Digital
® Audio coding system
and MLP Lossless
® for highest reproduction quality even with standard Audio DVDs.
“Dolby
®”, “MLP Lossless
®” and the Double-D-Symbol are trademarks of Dolby Labo-
ratories
®.
•
With the help of “DTS
®” and “DTS 2.0
®” the surrounding sound of a DVD is trans-
formed and replayed in best stereo quality. “DTS
®” and “DTS 2.0
®” are registered
trademarks of DTS, Inc.
š
CD
s32k.a.book Page 20 Friday, September 18, 2009 1:54 PM

Range selector key MEDIA
22
- changes over to the TV mode when a TV Tuner* is connected
⇒page 30.
- changes over to a Video-DVD inserted into the internal CD/DVD drive
⇒ page 28. Additional function keys in the AUDIO menu
- changes over into the
DVD menu
and plays the last selected video source.
- opens a pop-up window in which the repeat function determines whether
the or the (in audio CD operation) respectively the current (in the MP3 operation
⇒page 24) should be repeated.
- opens a pop-up window in which the random play function
Mix
or the auto-
matic play
Scan
, the capacity of the hard disk
HDD capacity
or Switch off display
can
be selected.
- opens the title list of the current audio source in order to select another title
or audio source. Additional function keys in the DVD menu
- changes to the
Audio menu
and plays the last selected audio source.
- switches over the DVD played in the internal CD/DVD drive to the menu selec-
tion of the film and also opens the incorporated menu control.
- opens a set-up menu to adapt the display set-ups for the current film. - opens the chapter selection for the DVD played in the internal CD/DVD
drive.Inserting or ejecting a CD/DVDInserting a CD/DVD– Push a CD/DVD with the written side facing up as far as possible into the CD/DVD
case until it is automatically drawn in. Th
e play function will start automatically.
Ejecting a CD/DVD– Press the button to move the CD/DVD
in the internal CD/DVD drive into the
eject position.
If a CD/DVD is not removed when ejected, it will be reinserted after approximately ten seconds for safety reasons. Pl ayable MP3 a nd WMA data ca n als o be stored o n the hard di sk of the unit
⇒page 27.
WMA Data (Windows Media Audio) The copyright of audio data compressed by
Windows
Media
Audio, can also be
protected by the DRM procedure (
Digital
Rights
Management). Such WMA data is not
supported by the unit.Inserting or removing a memory card Inserting a memory card– Push the memory card into the memory ca
rd case with the trimmed edge to the
front right (horizontal case) or to the front top (vertical case), until it is locked in position. The play function
will start automatically.
Taking out a memory card– Press against the spring resistance of the inserted memory card, the memory card
“skips” back into
the Eject position.
Destination entry from the memory card– You can enter the destinations from the SD card using the function
in the
Navigation menu
. The destinations must only be stored
on the SD card in the corresponding format.
Only MP3 data and unprotected WMA data can
b e re a d f ro m t h e S D c a rd . A l l o t h e r d a t a
is ignored. Pl ayable MP3 a nd WMA data ca n als o be stored o n the hard di sk of the unit
⇒page 27.
Memory card empty or data not readable If a memory card is inserted, on which no audio data has been stored, it will
not
be
switched over into the memory card mode
after the loading procedure. When in the
Audio menu
the function key remains inactive on the top line of the touch-screen
and the function cannot be seleced
⇒page 21, fig. 8
.
TVDVDVideoRepeat
titel
CD
folder
ExtrasSelect.AudioMenuDisplayChapter
š
Import destinations
SD
s32k.a.book Page 22 Friday, September 18, 2009 1:54 PM

Range selector key MEDIA
23
Requirements of the memory card•
Memory cards measuring 32 mm x 24 mm x 2.1 mm or 1.4 mm can be inserted into
the memory card case.•
SD (Secure Digital Memory Cards) and MMC (Multimedia Cards) memory cards
with a capacity up to 4 GB.•
SDHC (Secure Digital High-Capacity Memory
Cards) memory cards with a capacity
up to 32 GB.•
Due to the differing demands on quality of the card manufacturer, it is possible that
some of the data on the memory cards canno
t be played or their play is restricted.
Audio menuSelect title or audio sourceChange audio source– Press the range selector key to switch to the main menu
MEDIA
. If the last
selected was a video source, press the set-up key again to open the
Audio
menu
.
– When in the
Audio menu
the play function of the last played audio source will
continue from the last played point.
– Press one of the top function keys to
select the corresponding audio source. The
play function of the selected audio source
will continue from th
e last played point.
Opening the selection menu of the available audio sources– When in the
Audio menu
press the function key to display the title list of the
currently played audio source. The currentl
y played track is shown as highlighted.
– Press on the function key as often as necessary until the selection menu of the
available audio sources has opened.
– Press on the left of the audio source display , or the
content of these folders or data
carriers will then be indicated.
Changing track or selecting track manuallyPress the range selector key to switch to the main menu
MEDIA
. If the last
selected was a video source, press the set-up key again to open the
Audio
menu
.
Select track– Briefly press on the arrow keys on the unit or in the
Audio menu
or press on
the function keys on the screen or .
Fast forward/reverse– Keep pressing the arrow keys at the unit or or the function keys on the touch-
screen or .
– Release the corresponding key if the desired title sequence has been reached.Audio CD/DVD– Press the function key to display the title list of the currently played audio
CD/DVD.
– Select the title from the
title list by
pressing .
– Use the function key to switch from the title list back into the CD selection
menu or the selection menu of
the available audio sources.
– If you wish to select a CD, press the f
unction key . If the
vehicle is fitted
with a CD changer*, a window fo
r the CD selection is displayed.
MP3 Data: Select track– Press on the function key , in order to
display the title list with the currently
played title and, if necessar
y, to display the sub-folder
contained in this folder.
– Press on the display of a data folder to open it. – Press the function key to open th
e appropriate higher priority folder.
– By pressing several times, you will switch folder by folder to the selection menu
of the available audio sources. There you
can search for titles of another audio
source.
MEDIA
MEDIASelect.
F
I CD
K SD card
J HDD
MEDIA
MEDIA
ƒ
„
M
Lƒ
„
M
L
Select.
Title ...
y
CD selection
Select.F
F
s32k.a.book Page 23 Friday, September 18, 2009 1:54 PM

Range selector key MEDIA
24 Repeat track–Open the
Audio menu
⇒page 21.
– Press the function key . – Press on in the pop-up window to automatically repeat the current track at
the end.
– If you press on (Audio CD mode) or
(MP3 operation) in the pop-up
window the titles of the current CD
or the current folder are repeated
automatically.
Random play function – When in the
Audio menu
press the function key .
– Press on in the pop-up window. All titles of the current audio source will now
be played in random order.
– Use the function key to terminate the function of the current title. The
normal play function continues with the current title.
Automatic play (Scan function)– When in the
Audio menu
press the function key .
– Press on in the pop-up window. All the titles of the current audio source are
played for approximately 10 seconds.
– Press to terminate the play function
of the current title. The normal play
function continues wi
th the current title.
Alternatively, start and end the automatic
play by briefly pressing the set button .
Note
In the
Audio menu
, press on the function key and afterwards on
in the pop-up window, the information relati
ng to the assigned or free memory space
on the hard disk will appear on the screen.
MP3 dataGeneral information for MP3 operationRequirements for the MP3 data and data carrier•
CD-ROM, CD-R, CD-RW with a capacity of 650 MB and 700 MB.
•
4.7 GB DVDs and up to 8.5 GB Double Layer DVDs.
•
The CDs/DVDs must correspond to the IS
O 9660 Level 2 standard as well as the
Joliet data system (single and multi-session).•
Data names must be no longer than 64 characters.
•
The list structure is restricted to a depth of 8 list levels.
•
The name of the artist, the album and the
title of the reproduced MP3 data can be
shown as ID3 tag, providing this information is available. The list and data name will be displayed if there is no ID3 tag.•
WMA data (
Windows
Media
Audio) can also be played
even if the copyright is
additionally protected by the DRM procedure (
Digital
Rights
Management). Such
WMA data is not supported by the unit.•
The operation and behaviour of playable WMA data conforms to the MP3 data and
will not be described further. Bit rate (data flow per time unit) •
The system supports MP3 data with bit rates of 32 to 320 KB/s as well as MP3 data
with variable bit rates.•
The indicated playing time
data with variable bit rates is not reliable.
Information on how to use a CDCD to jump Uneven road surfaces and strong vibrations may cause the CD to jump. Formation of condensation When it is cold and after rain showers, mo
isture can deposit in the CD drive (conden-
sation). This can effect the CD jump or impa
ir the play function. In such cases wait until
the moisture has dissipated.
Repeat
Tra c k
CD
folder
MIX
Extras
Mix
b Mix
Extras
ScanbScan
A8
Extras
HDD capacity
s32k.a.book Page 24 Friday, September 18, 2009 1:54 PM