SKODA SUPERB 2010 2.G / (B6/3T) Columbus Navigation System Manual

General information
9
Climatronic If your vehicle is equipped with climatronic, a feedback is received on the screen when changing the settings. Display of time You can switch the display of the time on or off in the menu
Setup System
.
Switching the system on and off– The system is switched on or off by pressing the control button . The last active audio source before switching off is repeated. If the key is pulled out of the ignition lock while the unit is switched on, the unit will switch off automatically. You can then switch the unit on again. If the
ignition is switched off, the unit (discharge
protection of the vehicle battery) switches
off automatically after approx. one hour.
This process can be repeated as often as necessary.Anti-theft protectionThe anti-theft coding of your navigation sy
stem prevents an operation of the system
after a voltage interruption, e.g. during a vehicle repair or after theft. After discon-necting the battery, disconnecting the navigati
on system from the on-board voltage of
the vehicle and after a fuse failure, the code
must be entered before the vehicle can be
used again.Enter code– If a keypad appears after switching on
with the command to enter the code, the
unit can be unlocked by entering the corr
ect four-digit code number. The number
of the possible attempts is shown in the second touch-screen line.
– Press a digit from to on the digit block displayed on the screen. The digit is
accepted in the entry line.
– After a four-digit order has been entered, the group of digits will turn grey (inactive)
and no further digits can be accepted in the entry line.
– Press on the touch-screen to erase the digits in the entry line from right to left
and thereby correct your input, if necessary.
– If the correct code number is di
splayed in the entry line, press .
Code number The code number can only be called up “onlin
e” via the Škoda system, as this guaran-
tees even more effective anti-theft protec
tion. Please contact your Škoda dealer if
necessary. Incorrect code number If an incorrect code is confirmed after entry
of the code, the procedure can be repeated
once again
. The number of possible attempts is
shown in the second line on the
touch-screen. If the code number is entered incorrectly fo
r the second time, the unit will be blocked
for approx. one hour. It is possible to ente
r again the safety code
after one hour has
expired, when the unit and the ig
nition have been switched on.
If two invalid attempts are then made agai
n, the navigation syst
em will be blocked
again for an hour. The cycle - two attempts, blocked for
an hour - will continue to apply.
Note
The code is normally stored in the instrument
cluster. This ensures that it is automati-
cally decoded (convenience coding). Ma
nual input of the code is normally not
necessary.
A1
0
9

OK
s32k.a.book Page 9 Friday, September 18, 2009 1:54 PM

Range selector key TONE
10Range selector key TONESound settings By pressing the button , you can select the following parameters:•
- Setting of bass, mid and treble;
•
- Volume ratio (left and right = balance), (front and rear = fader);
• •
- setting the maximum volume
•
- setting the minimum volume
•
- setting the volume of the navigation announce-
ments, decreasing the media or the radi
o volume during navigation announcements
•
setting the minimum volume of
the navigation announcements
•
* - setting the volume when parking;
•
(GALA) - Speed dependent volume adapta-
tion;•
* - Activating an external DVD source;
•
- switching on or off the confirmation tone when operating the
display;•
* - Selecting the program type (linear, language, rock, classical, dance);
•
* - Setting of the surround tone.
GALA function Your radio increases automatically its volume with the increasing vehicle speed. A higher setting value results in a stronger volume increase. Volume decrease for park distance control (PDC) * If your vehicle is eq
uipped with “parking ai
d”, the volume is automatically decreased
to a pre-defined value, when the “parking aid” is active. Nav. announcements
- spoken driving recommendations from the navigation system are played during
the audio operation at a pre-set volume.
- spoken driving recommendations are only provided when you have left the
calculated route, for example on the basis
of announced traffic problems. This setting
is recommended if audible drive recommendat
ions are normally no
longer needed for
a daily driven route and navigation is only
used as dynamic naviga
tion. If an audible
driving recommendation is transmitted again on
the basis of a change in route, navi-
gation announcements must be switched on again (Display:
).
- no spoken driving recommendations
of the navigation system will be
transmitted.
TO NE
Sound settings: Bass - Mid - TrebleBalance-faderVolume settingsSwitch-on volumeTraffic announcementsNavigation and voice controlTelephone volumePDC: Reduce audio vol.Speed dependent volume adaptationAV-OutputAcoustic feedbackEQ settingsSurround
On
DynamicNav. announcements
b On
Off
s32k.a.book Page 10 Friday, September 18, 2009 1:54 PM

Range selector key SETUP
11
Range selector key SETUPMain menu set-ups (Setup)– Press the range selector key to open the main menu
Setup
.
Overview of the set-up menus
- When in the radio mode, carry out set-ups for the function of the arrow keys,
for the displayed memory keys, the preset list and the TMC traffic reports
⇒page 11,
“Setup radio”.
- Determine the set-ups for the play and display of MP3 data and activate or
deactivate the external audio sources
⇒page 12.
- Update the phone book in the unit, dele
te all call lists and modify the assign-
ment of the shortcut keys.
⇒page 12.
- Change the system set-ups such as voice response, time display of the air
conditioning system*, return to the original set-ups and delete set-ups if necessary ⇒ page 15.
- Adjust the brightness of the touch-screen, day/night design of the map
display and select/deselect the confirmation tone for the key stroke
⇒page 13.
- Carry out set-ups for the map display and select symbols for the display in the
map
⇒page 14, “Setup Map”. - Determine the set-ups for receiving driving recommendations, define or
change an address to a home address and
start a virtual demonstration drive with a
manually set starting point
⇒page 14.
- Select preferred TMC station, ad
just filter for TMC announcements
and activate/deactivate traffic reports
⇒page 15, “Setup traffic programme”.
- setting the dialogue style, the help display and deleting the voice
recordings.
- Carry out set-ups for voice response with an inserted Video-DVD and adjust
the aspect ratio of the touch-screen. It is
also possible to adjust the audio video
standard when operating an external media source
⇒page 15, “Setup Video” as well
as carrying out the set-ups for the TV operation.
Setup radioCall up the menu
Setup Radio
by pressing the range selector key and the func-
tion key on
⇒fig. 5
.
Determining the station selection via the arrow keys – Press on the or , to determine from which list in the radio
mode the stations are to be selected
with the arrow keys. If is selected,
only stored stations from the preset list
are called up using the arrow keys during
station relay. “
Memory
” is displayed at the top left in the main menu
RADIO
.
Regional function RDS (RDS Regional)– Press on the button (regional station) and select a set-up in the
opening pop-up window.
– Select the button , doing so always chooses the frequency for the heard
radio station which offers the best reception at the present time.
SETUP
RadioMediaPhoneSystemTouch-screenMapNavigationTraffic informationVoice controlVideo
Fig. 5 Menu: Setup Radio.
SETUP
Radio
Arrow keys
Station list
Preset list
Preset list
RDS RegionalAutomatic
s32k.a.book Page 11 Friday, September 18, 2009 1:54 PM

Range selector key SETUP
12– When selecting the button , the unit attempts to hold a radio station emitting
regionally long enough until the reception qu
ality is so bad, that there is a risk of a
program loss.
Switching the traffic announcements on or off– In the menu
Setup Radio
, press the function key to switch
the transmission of traffi
c announcements on or off. A tick in the check box
= indi-
cates that the traffic programme f
unction is already switched on.
Selecting preferred TMC station– In the menu
Setup Radio
the function key indicates the TMC
station from which current TMC traffic reports are received.
– Press on the function key behind and choose your prefered
TMC station.
– Press on if you wish your unit to
automatically search for a TMC station.
Delete preset list– Press the function key and confirm the following safety interroga-
tion in order to erase all radio stations stored in the memory list.
You can select the following functions: Preferred TMC station If the “preferred” TMC station can no longer be received, the system automatically searches for the TMC station offering the be
st reception for the currently driven area.
You can determine in the
Setup Radio
from which TMC station the reports are to be
announced.Setup MediaCall up the
Setup Media
menu by pressing the range
selector key and the func-
tion key . – Activate the check boxes before entering details
=, by pressing th
e corresponding
function key.
Function keys in the menu - Setup Media
- for the playback of an optional ex
ternal audio* or video source*, if
a TV tuner is installed.
- for the playback of an external audio source*. - Setting of the input sensitivity for an external source*.
- according to the set-ups the title and performer name or
only the data and folder name will be displayed for audio CDs with CD texts and in the MP3 operation.
- plays all MP3 data one after the other according
to the sequence on the played medium, which are stored in the folders and subfolders.
* - enables a wireless transfer of MP3 data from the telephone
preinstallation.Setup Telephone*Call up the
Setup Telephone
menu by pressing the range selector key and the
function key .Updating telephone book in the unit– Press on the function key to update all entries in the unit,
the telephone book of the mobile phone
or the SIM card entered since the last
connection. This procedure can take a few minutes.
– Confirm the following safety interrogatio
n. The “old” data in the phone book can
still be selected at the unit wh
ile the data is being updated.
Delete call lists– Press on the function key . – If you confirm the following safety inte
rrogation by pressing
, the stored call
numbers of all calls made and calls
accepted in the unit will be deleted.
Modifying assigned shortcut keys– Press the function key to modify the assigned shortcut keys.
Fixed
Traffic programme (TP)
Current TMC stat.: ...
Preferred TMC station
Automatic
Delete preset list
SETUP
Media
Activate AV entryActivate AUX inputAUX input stageDeactivate artist/title nameScan/Mix/Repeat including subfoldersActivate Bluetooth audio
SETUP
Phone
Update telephone bookDelete call lists
Delete
Speed dial
s32k.a.book Page 12 Friday, September 18, 2009 1:54 PM

Range selector key SETUP
13
– To change the assignment of a particular shortcut key, select the respective
shortcut key by pressing the key in the following menu.Note
The selection possibilities of the phone se
t-up depend on the relevant telephone
preinstallation.Setup SystemCall up the
Setup System
menu by pressing the range se
lector key and the func-
tion key .Change the system language manually– Press the button and select the de
sired language in the opening pop-up
window. When selecting the menu point “
automatic
”, the system language is the
language which is set in th
e menu of the information disp
lay. If desired, another
language can be selected for the unit.
Changing system set-ups– You can change the set-up of the distance unit. – You can change the set-up of the time format. – You can change the set-up of the date format.Time display– If you press the function key , while in the menu
Setup System
, the
automatic time display is set in the touch-screen.
– Time display in the operating modes radio, media and map. – The current time is taken over by
the instrument cluster in the vehicle.
– After switching off the unit, the time continues to show.Reset the factory settings on the unit– Press on the function key in the menu
Setup System
.
– Now find the settings you wish to reset. – If you press the function key and confirm the following safety interrogation
the selected settings will be reset to the factory settings and all the stored data will be erased.
“ Time
” and “
Date
” settings need only be carried
out manually under
certain circum-
stances. Time and date will normally be a
ccepted automatically from the vehicle into
the unit.Setup DisplayCall up the menu
Setup Display
by pressing the range selector key and the
function key .Brightness– Press on the function
key behind and select a setting in the pop-up
window.
– Press the function key if the brightness of the touch-screen should
automatically be adapted to the current ligh
t conditions via the sensors on the unit.
– Press one of the other function keys to
manually adjust the brig
htness of the touch-
screen.
Day/night– Press on the function key behind and select a setting in the pop-up
window.
– Press the function key if switching
the headlights on and off should also
change the map display from night to day design.
– Press on the function key or to manually determine the night and day
design of the map display.
SETUP
System
Language
time displayFactory settings
Reset
SETUP
Display
Brightness
Automatic
Day/night
Automatic
Day
Night
s32k.a.book Page 13 Friday, September 18, 2009 1:54 PM

Range selector key SETUP
14 Acoustic feedback– Press on the function key behind and select a setting in the pop-
up window.
– Press or to switch the tone for confirmation of a function key operation
on the touch-screen on or off.
Display off– Pressing the function key makes it possible to set the touch-
screen to energy save mode, the display
is black and the current information about
the audio source is only displayed in the lower part.
– The display can be switched on again by
touching the touch-screen or by pressing
any button, except the control button.Note
Please note that manual adjustment of the
display in unfavourable conditions can lead
to the displays in the touch-screen
no longer being clearly visible.
Setup MapCall up the menu
Setup Map
by pressing the range selector key and the func-
tion key . Position of the split-screen Intended for positioning the split-screen in the map display. Aiming symbol Shows the destinations in 2D or 3D. Select displayable map details Press to select a map detail which is to be displayed. Selected map details are indicated by a tick in the check box
= and at the bottom in the entry line.
Display favourite symbol If the check-box is activated
=, the destinations stored as favourite destination will be
displayed in the map with the symbol of the selected favourite destination.
Setting the speed limit If the check-box is activated
=, the current speed limit on the driven stretch of the
road is shown in the display.Setup NavigationCall up the menu
Setup Navigation
by pressing the range selector key and the
function key . You can select the following functions:•
- three alternative routes are suggested;
•
- Setting of the navigation announcements;
•
- during route guidance, either the arrival time or the driving time is
shown in the map display;•
- Enter home address;
•
- activation of the demo mode and entry of the
average rate for the time calculation. Demo Mode A virtual route guidance can be
started in the demo mode. Virtual route guidance will
be repeated when reaching the fictive travel destination.
Acoustic feedback
On
Off
Switch off display
SETUP
Map
Split-screen
Select map details
Fig. 6 Menu: Setup Navigation
SETUP
Media
Suggest 3 alternative routesNav. announcementsTime displayDefine home addressAdvanced navigation settings
s32k.a.book Page 14 Friday, September 18, 2009 1:54 PM

Range selector key SETUP
15
As in this case the unit must first reorient itself it can take some time, depending on the number of the currently tracked satellites, unt
il the unit has again found the real loca-
tion. Drive a short distance. Nav. announcements
- no spoken driving recommendations will be provided.
- spoken driving recommendations are only provided when you have left the
calculated route, for example on the basis
of announced traffic pr
oblems. This setting
is recommended if audible drive recommendat
ions are normally no longer needed for
a daily driven route and navigation is only
used as dynamic naviga
tion. If an audible
driving recommendation is transmitted again on the basis of a change in route, navi- gation announcements must be
switched on again (Display:
).
- spoken driving recommendations will
be transmitted in the running audio
mode. Adjustable average speed Depending on the set average speed, the unit will determine an arrival or driving time during a route calculation and disp
lay it depending on the set-up.
Setup traffic programmeCall up the menu
Setup traffic programme
by pressing the range selector key
and the function key . Selecting preferred TMC station Press on if you wish your unit to automatically search for a TMC station. Select displayable announcements Press if, during route guidance, only
the TMC traffic announcements relating
to the traffic problems along your rout
e should be dislayed. If you press on
, all current TMC traffic announcements are displayed.
Switching the traffic announcements on or off A tick in the check box
= indicates that the traffic programme function is already
switched on.
Setting voice controlCall up the
Setup Voice Control
menu by pressing the range selector key and
the function key .Dialogue style– Select - the system gives the whole message without shortening it or
select - the system shortens some of the messages or replaces them by an audible signal
(gong), thus the operation of the system is accelerated.
Help display– The selected help display shows a range of the most important possible
commands in a pop-up window
Possible commands are
:
Delete voice recordings– Deletes the stored voice recordings for individual menu points.Setup VideoCall up the menu
Setup Video
by pressing the range selector key and the func-
tion key .Changing voice response– Press the function key , or in the menu
Setup Video
and select the desired language in the pop-up window.
– Pressing will fully switch off the display of sub-titles.Changing the aspect ratio of the touch-screen display– The currently set aspect ratio is
visible behind th
e function key .
– Press on the function key and on or in the pop-up window.
All video data will now be repl
ayed in the set aspect ratio.
Set-ups for vehicles with TV tuner If a TV tuner is connected to the unit, you
will find here furthe
r set-up possibilities.
OffDynamicNav. announcements
bOn
On
SETUP
Tra f f i c i n f o
Preferred TMC station
Automatic
Message display
On route
All announcements
traffic announcements
SETUP
voice control
long dialogueshort dialogue
SETUP
Video
Audio language
Menu language
Subtitles
Off
DVD-Format
DVD format
4:3
16:9
s32k.a.book Page 15 Friday, September 18, 2009 1:54 PM

Range selector key RADIO
16Range selector key RADIORadio modeSelect radio stationAll radio stations with strong reception are au
tomatically stored in
the list of stations.
The list of stations is automatically updated on a regular basis.Call up main menu RADIO and choose frequency range– Press the range selector key to call up the
RADIO
main menu. The currently
heard radio station is indicated at the top of the touch-screen.
– Press the range selector key to change the frequency range. Alternatively,
press on the function key in the main menu
RADIO
and on or in the
pop-up window. The current frequency range is indicated on the top left on the display.
Changing radio station– When pressing the arrow keys
on the unit or the arrow keys on the touch-screen
of the main menu
RADIO
⇒fig. 7
, you change to the previous or following station.
Select a radio station from the station list– Press the function key to display all radio stations that can currently be
received.
Scan function– Press the set button on the bottom right of unit to start the
automatic play
for
the current frequency range. All radio stat
ions with strong reception are automati-
cally played for approximat
ely five seconds according to the sequence in the
station list.
– Alternatively, press on the function key and press on in the pop-up
window.
– Press the set button or function key again to end the automatic play of
the currently heard radio station.
Manual station finding– Turn the set button , to adjust a radio st
ation manually via it
s station frequency.
The scale of the selected frequency range is inserted in the frequency band in the lower part of the touch-screen.
– Briefly press the set button to terminat
e the manual frequency selection and to
display once again the function keys.Note
•
If “ memory
” appears at the top left of the displa
y, you can only change over to the
stations stored in the preset list with the help of the arrow keys.Save radio stationSave a radio station on a displayed station key– Continue to press one of the six station keys to displayed in the
RADIO

main menu until a signal tone sounds. The currently heard radio station is then stored on this station key.
Fig. 7 Main menu RADIO
RADIORADIOBand
FM
AM
A3
Station list
A8
Extras
Scan
A8
b Scan
A8
1 ...
6 ...
s32k.a.book Page 16 Friday, September 18, 2009 1:54 PM

Range selector key RADIO
17
Save radio station– Press on the function key
while in the main menu
Radio
⇒page 16, fig. 7
.
A pop-up window with a range of
memory space groups is opened.
– When you select a memory space group,
a menu for saving six radio stations is
opened.
– Select a memory space and save the stat
ion by pressing on the memory space.
– If a memory space is selected, which already holds a radio station, it will be
overwritten.
Calling up a saved radio stationIf the currently heard radio station is already saved in the preset list, the memory space number is displayed behi
nd the description of the frequency range (
FM
or AM
).
Calling up a station via the station keys– Briefly press on one of the six station keys to displayed in the main menu
RADIO
until a signal tone sounds.
Select stations from the preset list– In the pop-up window, select the station
keys to be displayed in the main menu
RADIO
.
– Press the display of the desired station in the preset list.RDS functionRDS (“
Radio
Data
System”) serves to transmit progra
m identification and additional
services therefore also enabling automatic tracking of stations. In the event of sufficiently satisfactory reception, the suitable RDS radio stations will display the station name instead of the station frequency. If a radio station sends additional informat
ion via the RDS function while a station is
being stored, it can occur that the name of
the radio station is later displayed incor-
rectly in the preset list.
Change station name You can manually adap
t the station name.
Choose the stored radio station and wait until the correct name is displayed on the touch-screen. Continue to press on the disp
lay of the station name between the arrow
keys until “
Station name stored
” is displayed.
Traffic programme function TPSwitching traffic programme TP (TMC Program) on or off– Press the range selector key to call up the
RADIO
main menu.
– Press the function key . – Briefly press on in the opening pop-up
window to switch the traffic programme
function on or off.
The display “
TP” in combination with a station name (e.g. in the station or preset list),
indicates a traffic programme station. Irrespective of which radio station is heard,
an additional receiver part in the unit
ensures that a traffic programme station can al
ways be received as
long as the traffic
programme function is switched on. The functionality of the tr
affic programme function “
TP” is displayed at the top right on
the touch-screen. If no traffic programme station can be rece
ived because, for example, radio reception
is interrupted in general, “
No TP
” will be displayed instead of “
TP”. Remember that car
parks, tunnels, high building
s or mountains can interrupt
the radio signal up to the
total loss of reception. Incoming traffic announcement If you wish to interrupt the transmission
of the traffic announcement, press on the
function key in the pop-up window
Traffic announcement
. The traffic
programme function remains available and
a following traffic announcement is made
again while the audio mode is in oper
ation. Pressing the function key
will switch off the traffic programme function permanently.
memory
1 ...
6 ...
RADIO
Extras
TP
Cancel
TP deactivated
s32k.a.book Page 17 Friday, September 18, 2009 1:54 PM

Range selector key RADIO
18Display offDisplay off– Pressing the function key makes it possible to set the touch-
screen to energy save mode, the display
is black and the current information about
the audio source is only displayed in the lower part.
– The display can be switched on again by
touching the touch-screen or by pressing
any button, except the control button.
Switch off display
s32k.a.book Page 18 Friday, September 18, 2009 1:54 PM