navigation SKODA SUPERB 2010 2.G / (B6/3T) Columbus Navigation System Manual

Range selector key NAV (Navigation)
49
Route guidanceStarting and stopping route guidanceSelect a travel destination or enter a tour and start the route guidance as described in the respective chapter. The unit will
switch over to the map display
⇒fig. 21
.
Route guidance in the map display– Press on the function key in the map display and on
⇒fig. 21

in the pop-up window to interrupt the route guidance.
– If you press the function keys and in the opening
pop-up window the route guidance wi
ll continue at the current position.
Route guidance in the main menu Navigation– Press the range selector key after route guidance has started to switch to the
main menu
Navigation
.
– Pressing the function key will interrupt the route guidance and “
Start
” will be
displayed again the function key.
– If you press on the function key the route guidance will continue at the
current position.
Select one of three alternative routes– If you have selected the function “
Suggest 3 alternative routes
” in the menu
Setup Navigation
, three selected routes to the chosen travel destination will be
calculated after the start of route guidance.
– If the calculation is terminated, three routes to the destination will be indicated in
the overview map. The three routes correspond to the selectable route options “Options”, “Fastest” and “Shortest” route.
– You are given further information to the respective route in the function keys on the
right. Route guidance will start on the sele
cted route as soon as you press one of
these function keys. The route options for the navigation are changed according to the selected route. You can change the route options at a later time.
After route guidance has started, the route becomes the first travel destination and is calculated according to the specified information. When switching to the map display, the map wi
ll always be opened in the last selected
type of display (2D, 3D, topographic).Receiving driving recommendations– Press the button on the unit, if you
wish to repeat the last audible driving
recommendation.
Fig. 21 3D map display during a

route guidance.
 ... /...
Stop route guidance
Navigation
Start route guidance
NAVStop
Start
Fig. 22 Optical driving recom- mendation in the split-screen of the map display.
A8
s32k.a.book Page 49 Friday, September 18, 2009 1:54 PM

Range selector key NAV (Navigation)
50– Press the range selector key in the
map display to insert the split-screen.
– Press the function key at the top left in the split-screen. – In the pop-up window press on to
display the direction arrows in the
split-screen
⇒page 49, fig. 22
.
– Press on in the pop-up window to
display an overview map in the split-
screen with the starting and finishing point.
Press briefly on this map to change its
type of display.
– Press the function key or the range selector key to close the split-screen. Route guidance tour plan When driving to a tour plan, route guidance
will start automatically to the next desti-
nation after reaching a stopover. If an exac
t stopover cannot be reached, it must be
deleted from the tour plan before route guidance continues to the next destination. If route guidance to the next destination has been started manually, only this destination will be approached and all further dest
inations of the tour
plan are ignored.
Note
•
If you have missed a turn-o
ff during route guidance an
d there is no other opportu-
nity to turn at that moment,
continue driving until the navi
gation system offers you an
alternative route.•
The quality of the messages transmitted by the unit depends on the available navi-
gation data and, during traffic problems, also
on the available traffic reports. The radio
stations broadcasting the traffic reports are responsible for the content and quality of the available traffic reports.Dynamic route guidance with TMC use Switching the dynamic navigation on or off– In the main menu
Navigation
press on the function key .
– In the map display, press on or on
⇒page 49, fig. 21
during
a route guidance and on in the pop-up window.
– In the menu
Route options
, press on the function key and select
the desired set-up by pressing yo
ur choice in the pop-up window.
– Press to confirm your input. Traffic problems received via TMC which affect the route are displayed in the map by means of a coloured symbol. Traffic proble
ms, which do not affect the route, are
displayed in the map by means of a grey
symbol. The direction in which a traffic
problem is found, is displayed by means of an arrow in the symbol. The duration of a traffic problem on the route is displayed
in the map by means of continuous PKW
(motor car) symbols
.
 Dynamic route
b Off
When the dynamic navigation is
switched off you will not be advised of traffic prob-
lems affecting your route duri
ng route guidance and you are not directed away from or
through the traffic problems. TMC traffic reports are updated automatically in the unit ⇒ page 51, “Requirements for a dynamic rout
e guidance” and displayed by pressing
the range selector key . If one of the announced traffi
c problems is on your route,
you can also switch on the
dynamic route guidance during the current
route guidance or block the route manually
⇒ page 52, “Manually blocking a stretch of the route”. Dynamic route
b Manual
If the dynamic navi
gation is set to
manual
and you are in route guidance mode you
can select to avoid the announced traffic problems on your route
⇒page 51,
“Requirements for a dynamic route guidance”. If the navigation system is alerted of a tr
affic problem on the calculated route, the
driver will be notified of this by means
of an audible message and information in a
pop-up window. The expected delay incurred in avoiding this traffic problem and the length of the alter- native route will be displayed. The expected time lost when driving through this traffic problem will also be displayed.•
Press to remain on the calculated route and to pass through the
traffic problem.•
Press on for an alternative route to
be calculated taking
into account the
announced traffic problem.
MAP
NAV symbol
Overview
O
MAP
Options
Navigation
 ... /...
Route options
 Dynamic route
OK
TMC
Current routeBypass
s32k.a.book Page 50 Friday, September 18, 2009 1:54 PM

Range selector key NAV (Navigation)
51
 Dynamic route
b Automatic
If the dynamic navigati
on system is set to
Automatic
and you are in route guidance
mode, you will automatically be guided around the announced traffic problem on your route
⇒page 51, “Requirements for a dynamic route guidance”.
After input of relevant traffic information
for your route you wi
ll be advised of the
change in the current route guidance by mean
s of an acoustic message. You will auto-
matically be guided around an
nounced traffic jams or blocked roads, if this saves time.
Such announcements will take place if a traf
fic problem affects the
original route calcu-
lation, the traffic problem has been solved and the navigation system can see only one possibility of driving the actually most advantagous route. Requirements for a dynamic route guidance TMC (Traffic Message Channel) is a digital radio data service for
continuous
transmis-
sion of traffic information. The unit has a continuous background of TM
C traffic reports providing a TMC station
at the current location can be received. The quality of the transmitted traffic reports depends on the broadcast editing carried out by the radio station. The reception of
the TMC traffic reports cannot be switched
on or off. The station you are listening to does not have to be a TMC station.TMC traffic reports can only be evaluated an
d displayed by the uni
t if the navigation
data for the currently driven area is stored
in the unit memory or can be called up via
an inserted navigation DVD. The current TMC traffic reports can be disp
layed by pressing the range selector key
.Note
•
There may not be any advantage in avoiding the traffic jam if, as a result of the TMC
traffic reports, the diversio
n is also heavily congested.
•
You can manually block the information for th
e route in front of you if traffic prob-
lems ahead have not yet been included in the TMC traffic reports
⇒page 52.
Fade in route or manoeuvre listThe route or manoeuvre list can only
be displayed during a route guidance.
Split-screen in the map display– Press the range selector key in the map display to open the split-screen. – Press on the function key on the top left in the split-screen and on
in the pop-up window. The ma
noeuvre will be displayed
⇒fig. 23
. The route list
can only be called up via the main menu
Navigation
.
Main menu Navigation– You can open the main menu
Navigation
during route guidan
ce by pressing the
range selector key .
– Press on the function key in the main menu
Navigation
and on or
in the pop-up window.
In the
Manoeuvre list
the turning points still to be pa
ssed will be displayed in the list
by means of direction arrows. Street name or street description refers to the street into which to turn
⇒fig. 23
.
In the
Route list
the street names or street descriptions for the parts of the journey still
to be driven are displayed in a list.
TMC
BAT-20H647
Fig. 23 Manoeuvre list in the map display.
MAP
Manoeuvre list
NAV
Route
Route list
Manoeuvre list
s32k.a.book Page 51 Friday, September 18, 2009 1:54 PM

Range selector key NAV (Navigation)
52Manually blocking a stretch of the routeCongestion ahead– Press on the function key in the ma
p display during a route guidance or
on the function key in the main menu
Navigation
.
– Press on the function key in the pop-up window. An overview
map will be displayed together wi
th the current vehicle position
9 and the travel
destination
3.
– Turn the set button anti-clockwise, move a flag symbol
4 starting from the
travel destination in direction of the current vehicle position. Use the finger to press on the displayed route and the flag symbol
4 will “skip” directly to this point. The
distance taken up by the current congesti
on will be displayed as of the current
vehicle position at the bo
ttom in the touch-screen.
– Press the set button or the function key , when the approximate length of the
stretch of the road to be
bypassed is displayed.
– You will receive an audible announcement
that parts of the route are blocked and
that the alternative route is being calculated.
Permanent congestion– Press the function key and then in the main menu
Navigation
during route guidance.
– - if you wish to add a further blocked section to the
route.
– Locate the start of the congestion
4 by pressing on the
route indicated on the
touch-screen and confirm it by pressi
ng the function key . The end of the
congestion is set in the same way.
– Name of the congestion - you can name th
e congestion with the help of the input
mask for the text entry.
– - finally deletes th
e excluded sections
from the memory of the navigation unit.
– - deletes the congestion entered with the button
Received TMC traffic reports wi
ll be displayed in the map as
traffic problems. Currently
announced traffic problems can also be disp
layed in the list of TMC traffic reports.
... /...
Route
Congestion ahead
A8
OK
Route
Manage blocked routes
Add excluded street section
OK
Delete excluded rd. section/area to be avoidedDelete temporary congestionCongestion ahead
s32k.a.book Page 52 Friday, September 18, 2009 1:54 PM

Range selector key MAP
53
Range selector key MAPMap displayBy pressing the range selector key you
can move from any menu into the map
display. Pressing the range selector key will op
en or close an split-screen in the map
display, where further informatio
n can be displayed and selected
⇒page 56, “Split-
screen in the map display”. During route guidance the map display will di
ffer in some points from the “normal”
map display. During the rout
e guidance the driven route will be highlighted, symbol
9, shows the current vehicle position
⇒fig. 24
- in the bottom line behind the third
function key
 and the distance to the destination and, behind
 the estimated time
of arrival or driving time will be displayed. Parts of the road ahead can also be blocked manually during route guidance.Use the function key to insert or fade out the bar with the function keys in each display.
Center the map display for vehicle position or travel destination You can move the indicated map section by pr
essing your finger on the touch-screen
and sliding it over the touchscreen. If you have moved the touch-sc
reen section, a further function key will be faded in at
the top right under the compass display function key
³ ⇒fig. 24
. Pressing this func-
tion key will center the map again for the current vehicle position. In some map displays you can center the di
splay of the travel destination with the
function key . Change the type of display The symbol in the second function key
5, 6 or 7 shows the currently selected type
of display. To change these, briefly press press the function key and select a different type of display in the pop-up wind
ow by pressing the selection again.
5-2D
- Two-dimensional:
Plan view of a conv
entional map display.
6-3D
- Three-dimensional: Map display, diag
onally from the front in bird's-eye
perspective.7-To p o g ra p h i c
- Plan view of a conventional ma
p display with coloured display of
various terrains (Mo
untains, Valleys etc.).
The function key in the map display without route guidance Pressing on the function key will op
en a pop-up window
with settings for
navigation.
- starts route guidance or continues route guidance to the travel
destination selected in the main menu
Navigation
.
- calls up the menu
New dest.
to change the travel destination
selected in the main menu
Navigation
.
- to change the parameters for route calculation.
- stores the current vehicle position
as flagdest. in the destination memory.
Fig. 24 3D map display during a

route guidance (map section moved).
MAPMAP
8
1
Navigation
Navigation
Start route guidanceEnter new destinationRoute options$
s32k.a.book Page 53 Friday, September 18, 2009 1:54 PM

Range selector key MAP
54For further functions of the navigation syst
em, e.g. changing the travel destination,
open the main menu
Navigation
by pressing the range selector key .
The function key in the map display during a route guidance Pressing the function key
⇒page 53, fig. 24
will open a pop-up window with
set-ups for route guidance.
- stops route guidance at the cu
rrent position. The route guidance
can be continued at any time by pressing the function key and
.
- calls up the menu
New dest.
in order to enter a stopover to
be approached during
current route guidance.
- used for the manual entry of a congestion ahead and the recom-
mendation of the next available route.
- to change the parameters for route calculation.
- stores the current vehicle position
as flagdest. in the destination memory.
For further functions of the navigation, open the main menu
Navigation
by pressing
the range selector key . Control media source The function key displays the currently selected media source (here the radio station “Radio 2”). To control the selected media source, briefly press the function key and select a station (radio mode) or title (media mode) by pressing the selection in the pop-up window. Radio mode:
The six station keys of the main menu
RADIO
are faded in.
Media mode:
The title name and the function ke
ys for controlling the current media
source are faded in. Function keys Pressing the function key will open a
pop-up window for further set-ups and
displays.
- shows the currently selected travel destination in the map display in
the main menu
Navigation
. Use the function key on the right under the compass
display to center the map ag
ain on the vehicle position.
- changes between day and night design.
- opens the split-screen. The split-screen can be opened or closed in the
map display by pressing the range selector key .
- during route guidance, when driving and turning on roads with
more than one lane, a small split-screen with
lane guidance will be inserted in the map
display. A tick in the check-box
= indicates that the function is switched on.
- switches the touch-screen
into energy save mode.
Scale modification and display Pressing the function key with the display
of the currently selected map dimension at
the bottom right will insert further function
keys for changing the map detail and the
map scale. If not used, these function
keys fade out again after five seconds.
- briefly switches the map display to the
overview display (small scale). It returns
again to the last display (large scale) after a few seconds. or - to zoom in or out of the map, i.e.
changing the map scale. Alternatively, move
the sliding regulator
? within the scale.
- switches to the overview map with start and finish point during route guid-
ance.
- for switching on the autozoom during a route guidance. If “Autozoom” is active,
the map scale will change automatically depending on the driven route (Motorway trip: large map scale - city: small map scale). The switched-on Autozoom is displayed in the scale display by
{. Press again to switch off
or manually change the scale
with the set button . Display favourite symbol A favourite category can be determined for stored destinations. Favourite destinations are displayed in the map, depending on set-up, with their assigned favourite symbol.
NAV
 ... /...... /...
Stop route guidance
Navigation
Start route guidanceEnter stopover destinationCongestion aheadRoute options$
NAV
Radio 2Extras
Extras
Destination viewDay/night
Split-screen
MAP
=Lane guidanceSwitch off display/+
-
h-3
{
{
A8
s32k.a.book Page 54 Friday, September 18, 2009 1:54 PM

Voice control of the radio navigation system
61
Voice control of the radio navigation systemGeneral informationIntroductionThanks to this equipment, you can operate
a few functions of your radio navigation
system via the microphone installed in the vehicle; a so-called “
Speak what you see
on the touch-screen
” system.
You can use the voice control in the operating modes
RADIO, MEDIA, PHONE, MAP
and NAV
.
You can change the volume any time during
the call with the control button of the
unit
⇒page 3.
Switch on voice control (dialogue)•
By briefly pressing the button on the unit.
Switching off voice control (dialogue)•
By pressing the button on the unit for at least 5 seconds.
•
By briefly pressing the button on the
unit, when the system is waiting to
pronounce a new command.•
By pressing one of the buttons which are located on the side of the touch-screen
of the unit or by touching the touch-screen
(if the button is not pressed in the
help display).•
By pronouncing the command “
Cancel
”.
•
If the system does not receive a command or does not recognise the command
while the dialogue is switched on, it answers with the question “
Pardon?
” and thus
makes it possible to pronounce a new co
mmand. If the system does not receive a
second voice command, you will be offered help
. If the system does not receive a third
voice command, you receive the message “
Cancel
” and the voice control switches off.
Optimum understanding of the commands depends on several factors:•
Speak with a normal tone of voice wi
thout intonation and excessive pauses.
•
Avoid a bad pronunciation.
•
Do not use any abbreviations - al
ways pronounce the full command.
•
Do not speak, if the system makes an announcement. As long as the system has not
finished the announcement, it will
not react to an additional command.
•
Close the doors, windows and sliding roof, in order to avoid disturbing influences
of the environment on the understanding of the commands.•
We re c o m m e n d t o s p e a k l o u d e r a t h i g h e r s p e e d s ; b u t w i t h a c a l m v o i c e , s o th a t t h e
increased surrounding noise does not drown out the command.•
During the dialogue limit additional noise in the vehicle, e.g. simultaneously talking
occupants.•
The microphone for voice control is directed
to the driver as well as to the front
passenger. Therefore the driver and the front passenger can operate the unit.DialogueThe period of time in which the system
is ready to receive voice commands and to
carry them out is call
ed a dialogue. The system reacts
with an audible feedback and
guides you through the individual functions. Selecting long and short dialogue The nature of the dialogue can be set by
pressing the button on the unit and by
pronouncing the command “
long dialogue
” or “
short dialogue
”.
The nature of the dialogue can also be
set manually in the operating mode
SETUP
-
- or .
If you select the short dialogue, the system shortens some messages or replaces them by an audible si
gnal (gong), thus the operation is accelerated.
If you select the long dialogue, the system
gives the whole message without shortening
it. The entered voice commands are the same for the long and short dialogue. Interrupt messages The message just given can be ended by br
iefly pressing the button on the unit.
Thus, it is possible to pronounce
an additional voic
e command sooner.
A1



Fa d e o u t

Voice control
Long dialogue
Short dialogue

s32k.a.book Page 61 Friday, September 18, 2009 1:54 PM

Voice control of the radio navigation system
62Voice commandsThe voice control is only possible in the following languages:
Czech, English, German, French.
Due to the large number of possible voice
commands, we give here only a few exam-
ples. Therefore, please observe the system guidelines when entering voice commands. The system only recognises 30 000 entries (i.e, it will only recognise 30 000 of the largest cities for the selected country
, for example, in the operating mode
NAV
. If the
desired city is not included
in the 30 000 entries, it cannot be pronounced normally,
but it must be entered by spelling it out. Call up the general information for the voic
e control by briefly pressing the button
on the unit and by pronouncing the command “
Instructions
”. Then you hear a
message that the instructions are divided into seven parts. If you want more detailed information about individual parts of th
e instructions, pronounce for example the
command “
Tutorial part 2
”.
Call up the general help for individual oper
ating modes by briefl
y pressing the button
on the unit and by pronouncing the command “
Help Quick Commands
”.
Changing between the operating modes If you wish to change between the operating modes after switching on the voice control, always pronounce the name of th
e operating mode in which you wish to
change. This means, if you are in the operating mode
RADIO
and you wish to change
into the operating mode
MEDIA
pronounce the command “
Media
”. Always
pronounce the names of the operating modes
PHONE, MAP, NAV
as “
Telephone,
map, navigation
”.
Voice command “Help” Help can be called up by pronouncing the command “
Help
”. Depending on the oper-
ating mode in which you are, the help given wi
ll offer different possibilities. If the possi-
bilities offered are not sufficient, pronounce the command “
further options
”.
If you pronounce the command “
Help
”, you can hear a mess
age on how the command
should be correctly pronounced (e.g. “
auto Zoom
”).
Help display If you want the help to be displayed on the touch-screen of the unit, you must only activate it (then deactive it) manually in the operating modes
SETUP
, and
.
The help display can be set separately for
each operating mode in the system (this
means, if you only set the help display for the operating mode
MAP
, it is only displayed
in this operating mode). The help display includes so-called global and local commands. The range of these commands is indicated in
the pop-up window
Possible commands are
:
•
Global commands - commands which can al
so be used for another operating
mode than the one you are currently in, this means if you are in the operating mode RADIO
and you pronounce the command “
New dest.
”, the system changes over into
the operating mode
NAV
,
•
Local commands - commands which can only be used in the operating mode in
which you are currently in and are always shown in brackets. If you do not wish the help display to be
shown when the dialogue is switched on,
pronounce the command “
Block out
” while you are in the help display or press the
function key . The help display is show
n again after repeatedly switching on
the dialogue. Voice recording In the operating modes
PHONE
, NAV
and
RADIO
a short voice recording can be set up;
after pronouncing the recorded term the de
sired command is carried out (e.g. in the
operating mode
PHONE
, a voice recording can be set up besides a telephone contact
and after pronouncing it the system carries out the selection procedure.Further voice commandsIf you wish to scroll through the lists in the operating modes
MEDIA, PHONE, NAV,
RADIO
(e.g. in the operating mode
RADIO
in the list of the radio station), you must
pronounce the command “
next page
” or “
previous page
”.
If you are in a list in which the details are shown (e.g. in the operating modes
NAV
,
, ), pronounce the command “
Options for entry
” and then
select a number by pronouncing the command “
Options for entry 3
” or “
Details for
entry 3
”.


Voice control
Visual help
Fa d e o u t
New dest.
Last destinations
s32k.a.book Page 62 Friday, September 18, 2009 1:54 PM

Voice control of the radio navigation system
63
Certain voice commands in the operating mode RADIO If you pronounce the command “
Read station list
”, the system reads the list of the
radio stations. The desired selected radio stat
ion can be selected by
briefly pressing the
button on the unit during the message, then the system offers selection possibili- ties for the selected entry. If you directly pronounce a station name,
the system switches over to the desired
station. Examples for voice commands in order to op
erate buttons on the touch-screen of the
unit:•
“ next station
”
•
“previous station
”
Certain voice commands in
the operating mode MEDIA
Examples for voice commands in order to op
erate buttons on the touch-screen of the
unit or examples for voice commands fo
r which no help display is indicated:
•
“Back
” - return one step back and end the dialogue (function key can also
occur in other operating modes),•
“ Up” ,
•
“Next title
” ,
•
“Previous title
” ,
•
“Pause
” ,
•
“Play
” ,
•
“Bluetooth audio
” .
Certain voice commands in the operating mode PHONE The digits
zero to nine
are permitted. The system does
not detect any digit combina-
tions such as twenty-three You can enter the telephone number as a contin
uous row, as individually spoken digits
(the whole number at once) or in the form of
digital blocks (separated by short pauses).
After each digital block (separated by a sh
ort pause) the system repeats the detected
digits. Before entering the digits, you ca
n enter additionally a symbol “
Plus (+)
” for interna-
tional calls.
If you pronounce the command “
Read phone book
”, the system reads out the tele-
phone book. The desired telephone contact can be selected by briefly pressing the button on the unit during the message,
then the system offers selection possibili-
ties for the selected entry. Certain voice commands in the operating mode MAP Examples for voice commands in order to operate buttons on the touch-screen of the unit or examples for voice commands fo
r which no help display is indicated:
•
“Direction of travel
” 9 and “
North
” - changes the orientation of the map,
•
“Move map
” - moves the map, then pronounce the command “
to the left
”, “to the
right
”, “up”, “down
”,
•
“Position map
” or “
Reset view
” - if the display of the current position
9 on the
map has moved with the complete map from th
e centred position to both sides, to the
top or to the bottom, the map is again centred.•
“ Orientation zoom
”, “Rocket zoom
” - briefly switches the map display to the
overview display (small scale). It returns again to the last display (large scale) after a few seconds,•
“ Zoom in
” or “
zoom out
” - enlarges or reduces the map scale.
•
“Show info
” - shows info (e.g GPS coordinates) of the entry which was displayed
in the map.•
“ Save
” - if you wish to save for example the selected route in the operating
mode
NAV
.
Certain voice commands in the operating mode NAV If you pronounce the name of the desired ci
ty and the system is not sure about the
entry made or the name of the city is identical
to other cities, it offers a list of cites with
the utmost probability. You can scroll through the commands “
next page
” or
“ previous page
” in the list, then chose the desired city by pronouncing the command
e.g. “
Number 1
” or “
1”.
While in the operating mode
NAV
, the system does not allow you to enter post codes.

„
ƒ
y
y
F
L
M
Nb



/
+
-
º
,
s32k.a.book Page 63 Friday, September 18, 2009 1:54 PM

Index
64Index AAudio
Audio menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Change audio source . . . . . . . . . . . . . . . . . . . . . . . 23Changing track . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Title list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Audio mode
Repeat track/folder . . . . . . . . . . . . . . . . . . . . . . . . 24
CCD
Ejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
CD mode
CD not legible . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Center map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Certain voice commands in the operating mode MAP
63
Certain voice commands in
the operating mode MEDIA
63
Certain voice commands in
the operating mode NAV 63
Certain voice commands in the operating mode PHONE
63
Certain voice commands in
the operating mode RADIO
63
Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Control elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
DDest. entry
Coordinates entry . . . . . . . . . . . . . . . . . . . . . . . . . 40Destination on map . . . . . . . . . . . . . . . . . . . . . . . 40POI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Dest. memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Destinations
delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42edit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Dialogue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Driving recommendations . . . . . . . . . . . . . . . . . . . . 49 DTMF key tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60EEPG - Program guide . . . . . . . . . . . . . . . . . . . . . . . . . 33External sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25FFurther voice commands . . . . . . . . . . . . . . . . . . . . . . 62GGeneral information . . . . . . . . . . . . . . . . . . . . . . . . 3, 61
HHDD
Edit audio data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Help display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62LLast destinations
edit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
MMain menu
PHONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57Setup (SETUP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
MAP
Map display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Map
Location display . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
MP3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24MP3 Operation
Return folder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
NNavigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Destination address . . . . . . . . . . . . . . . . . . . . . . . 38Destination entry . . . . . . . . . . . . . . . . . . . . . . . . . . 38Determine route options . . . . . . . . . . . . . . . . . . 36
s32k.a.book Page 64 Friday, September 18, 2009 1:54 PM