transmission SSANGYONG KORANDO 2013 User Guide

8710-01
REKES key switch description
Door LOCK (locks the doors and tailgate when pressed briefly) 1.
All doors and the tailgate are locked and the theft deterrent mode is activated.
When the theft deterrent mode is activated, the hazard warning lamp flashes twice. When this
button is pressed once more within 4 seconds, the hazard warning lamp flashes twice and the
buzzer sounds once. -
-
Panic (Press and hold for 2 seconds or more) 3.
If this button is pressed for 2 seconds or more, the hazard warning lamp flashes while the buzzer
sounds for approx. 30 seconds.
If the door LOCK button or panic button is pressed, this function is deactivated. -
- Door UNLOCK (unlocks the doors and tailgate when pressed briefly) 2.
If this button is pressed briefly, all doors and the tailgate are unlocked and the theft deterrent
mode is deactivated.
When the theft deterrent mode is deactivated, the hazard warning lamp flashes once.
In theft deterrent mode, if a door, tailgate or engine hood is not opened within 30 seconds after
the door is unlocked by a remote controller, the doors are locked with the hazard warning lamp
and buzzer activated (lamp flashes twice and buzzer sounds once, the theft deterrent mode is
activated again). -
-
-
13. REMOTE KEYLESS ENTRY SYSTEM (REKES)
REKES key (Transmitter)
When the user operates the switch of the REKES key, the vehicle control message formatted by the
remote controller CPU is sent to the main part via radio transmission. The CPU of the main part controls
the vehicle and the main part controls the vehicle operations.
Door LOCK
Door UNLOCK
Panic
The escort function is activated with the headlamp ON for 20 seconds when the door LOCK button
is pressed for 0.5 seconds or more in the theft deterrent mode. If the door LOCK button is pressed
briefly or the ignition is turned ON during the escort operation, the escort is deactivated.

8712-03
Smart key module
1. SPECIFICATIONS
Component Item Specifications
SKM unit
(Electric)Rated voltage 12.0 V
Operating voltage9.0 V to 16.0 V
(CAN: 6.0 V to 18.0 V)
Operation temperature
Max. operating humidity 95%
Dark current 5.5 mA
Voltage drop 1.0 V or less
SKM unit
(wireless)Receive frequency
Frequency bandwidth
Modulation typeFSK
(Frequency Shift Keying)
Receive distanceRF: 10 m or more (without obstacles)
LF: 1.2 m (without obstacles)
Smart key
Component Item Specifications
Smart key
(Electric)Operating voltage 2.7 V to 3.3 V
Operation temperature
Battery type CR2032
Smart key
(wireless)RF (Radio
Frequency)
(transmission)LF (Low Frequency)
(receiving)
Sending/receiving
frequency
Modulation typeFSK
(Frequency Shift Keying)

8712-03
Exterior (bumper) antenna
Mounting location Component
LF transmission for valid smart key searching outside area of rear
bumper when tailgate open switch signal input
Door handle switch & antenna
Mounting location Component
LF transmission for valid smart key searching outside vehicle
(passive entry and KEY IN/OUT)
SKM exterior
antenna
Door handle
switch
Interior (rear) antenna
Mounting location Component
LF transmission for valid smart key searching inside vehicle
(passive start and KEY IN/OUT)
Interior (center) antenna
Mounting location ComponentESCL
Mounting
locationComponent
The ESCL (Electric Steering Column
Lock) is a device which locks the
steering handle with an electrical
signal.

8712-03
Passive entry function actuation area: Within 1.2 m from the door handle antenna
Passive tailgate open actuation area: Within 1.2 m from the center of the bumper -
-
(1) Passive entry actuation area
Searching for a smart key signal from the outside the vehicle is prioritized in the theft deterrent mode
when the passive entry signal is input. Searching for a smart key signal from the inside is prioritized
when the theft deterrent mode is deactivated.
The system searches a smart key only in the actuation area of a switch, which the signal is input
(driver/passenger door handle switches and tailgate open switch). -
-
4. PASSIVE ENTRY MANAGEMENT
1) Passive Function
The passive entry actuation area refers to the area where passive LOCK/UNLOCK can be
performed by pressing the switch on the driver or passenger door handle with a smart key carried by
the driver.
The passive tailgate open actuation area refers to the area where the tailgate can be opened by
pressing the tailgate switch with a smart key carried by the driver. -
-
LF transmission: Verification request signal
RF transmission: Response signal

8712-03
No engine operation
When the START/STOP button is pressed at the vehicle speed of 3 km/h or less, the SKM turns off
the IGN relay to stop the engine.
When the vehicle speed is 3 km/h or more or no speed signal is input, the SKM performs the
following functions: 1.
2.
Vehicle status Conditions
3 km/h or faster - When the START/STOP switch is pressed for 3 seconds
or more, the ignition status is changed from IGN to ACC.
- If the engine START/STOP switch is pressed again, the
ignition status is changed from ACC to IGN.
Abnormal vehicle speed
(No or abnormal CAN signal)- When the START/STOP switch is pressed for 3 seconds
or more, the ignition status is changed from IGN to ACC.
- If the engine START/STOP switch is pressed again, the
ignition status is changed from ACC to Power OFF.
(DTC set)
When the START/STOP button is pressed and held with IGN ON, the ignition status is changed to
OFF. When the START/STOP button is pressed briefly, the ignition status is changed to ACC ON. 3.
ACC ON to Power OFF
The SKM changes the ignition status to OFF from ACC ON when:
the engine START/STOP button is pressed with the brake pedal released after the ignition status is
changed from IGN ON to ACC ON.
the REKES LOCK or passive LOCK signal is input with ACC ON.
the driver door is opened with ACC ON.
(Driver door open signal input through B-CAN)
12 minutes have passed with ACC ON. 1.
2.
3.
4.Condition for starting request transmission 8.
ACC ON: Gear selector lever (P/N), Brake switch ON, START/STOP switch signal
IGN ON: Vehicle in stationary, Gear selector lever (P/N), Brake switch ON, START/STOP
switch ON -
-
Condition for canceling starting request 9.
At engine starting completed -

8712-03
(4) Smart key battery discharge warning (3) Smart key verification fail warning
When the verification is requested for ignition status change or engine starting and no verified smart key
is in the vehicle, the SKM sends the "smart key verification status" signal, which indicates that the
verification has failed, for up to 10 sec. until the verification fail conditions are deactivated. for up to 10
seconds. until the verification fail conditions are deactivated.
Verification fail detection and transmission conditions
When the ignition status is changed after a smart key is verified by the START/STOP switch ON
input, the SKM sends the verification status for 10 sec. -Normally, the smart key verification warning is one of the smart key fail conditions. -
Ignition status change
(OFF -> ACC) / (OFF -> IGN)/(ACC -> IGN) / (IGN -> engine ON) *
If above conditions are met again, the SKM re-verifies a smart key and sends the verification status
for another 10 seconds.
When the ignition status is changed by the transponder verification while the smart key status is sent
through the B-CAN, the SKM sends the smart key verification signal and also sends the transponder
verification signal for 10 seconds. -
-
If low smart key battery is detected during the verification process for ignition status change or engine
start, the SKM sends the signal for "smart key battery low voltage warning" to the BCM and instrument
cluster through the B-CAN for up to 10 sec. until the warning condition is deactivated.
Smart key battery discharge confirmation and deactivation
If the smart key battery low voltage is confirmed, the SKM sends the smart key battery low voltage
warning signal.
If the smart key battery is in normal condition, the SKM sends the smart key battery low voltage
warning deactivation signal.
The smart key is the last used key. -
-
*
(5) Transponder verification fail warning
If a verified smart key is not found by the key verification process, the SKM sends the information that
indicates the key is not verified to the instrument cluster through the B-CAN for up to 10 seconds until
the warning condition is deactivated.
The SKM sends the transponder verification warning when the verification has failed with the smart
key inserted into the immobilizer holder. -
Transponder verification fail detection and transmission conditions
When the ignition status is changed after the transponder is verified by the START/STOP switch ON
input, the SKM sends the transponder verification status for 10 sec. -

Ignition status change*
If above conditions are met again, the SKM re-verifies the transponder and sends the verification
status for another 10 sec.
When the ignition status is changed by a smart key verification while the transponder verification is
processed, the SKM sends the signal for [transponder verification fail], and sends the smart key
verification status for 10 sec. -
-
(6) Transmission position warning
When the gear selector lever is in a position other than P or N with IGN ON and engine started, the
SKM sends the [gear position warning] signal to the instrument cluster through the BCAN for up to 10
sec. until the operating conditions are deactivated.
Transmission position warning deactivation
When re-attempting to start with IGN1 ON and transmission in P or N -
(7) ESCL JAM warning
The SKM transmits the warning active command to the BCAN through the BCAN signals such as ESCL
NOT LOCKED warning signal or ESCL JAM warning signal within 10 seconds or until the active
command deactivation conditions will be met, if jam is occurred when the electric steering motor is
locked/unlocked.
Failure Detecting Conditions
When the UNLOCK retry occurs after ESCL LOCK command, the ESCL LOCK is performed.
- The UNLOCK retry is possible up to 2 times automatically. If the UNLOCK retry occurs 3 times
in succession, the ESCL NOT LOCKED warning is triggered.
- Reactivates when the ESCL LOCK conditions are met.
When the LOCK retry occurs after ESCL LOCK command, the command will be overridden without
retry.
- After the command is overridden, the ESCL NOT LOCKED warning is triggered.
- Reactivates when the LOCK conditions are met by pressing the START/STOP switch after
ESCL UNLOCK.
When the LOCK retry occurs after ESCL UNLOCK command, the ESCL UNLOCK is performed.
- The LOCK retry is possible up to 2 times automatically. If the LOCK retry occurs 3 times in
succession, the ESCL JAM warning is triggered.
- Reactivates when the ESCL UNLOCK conditions are met by pressing the START/STOP
switch.
When the UNLOCK retry occurs after ESCL UNLOCK command, the command will be overridden
without retry.
- After the command is overridden, the ESCL JAM warning is triggered.
- Reactivates when the UNLOCK conditions are met by pressing the START/STOP switch after
ESCL LOCK. 1.
2.
3.
4.

8712-03
(9) SKM error alert
The SKM sends the SKM error alert signal to the instrument cluster through the B-CAN for up to 10
sec. when an in ignition status related error or passive entry system error occurs.
SKM error transmission conditions
When any of the following errors is detected and a DTC is set, the SKM sends the error alert signal for
10 sec.
B+ (power) low voltage
B+ (logic) low voltage
ACC ON fail
ACC OFF fail
IGN1 ON fail
IGN1 OFF fail
IGN2 ON fail
IGN2 OFF fail
START/STOP switch short circuit 1.
2.
3.
4.
5.
6.
7.
8.
9.ESCL JAM Warning Deactivation
met again by pressing the START/STOP switch to change the ignition status within 10 seconds or after
10 seconds triggering the warning.
(8) ESCL FAIL warning
The SKM monitors the ESCL and transmits the warning active command to the BCAN for 10 seconds
Failure Transmitting Conditions
ESCL bolt status failure
ESCL no response error
- No response or incorrect response from ESCL 3 times in succession
Status mismatch
- Mismatch between ESCL bolt status and micro switch status
ESCL anti-scanning error
- Verification fails 2 times in succession 1.
2.
3.
4.

(10) Brake not working alert
The SKM sends the brake not working alert signal for 10 sec. every time the ignition status is changed
after the 1st cycle (OFF-ACC-IGN-ACC-OFF)
while the brake is not operated.
when the brake pedal is depressed, the system is reset and alert deactivation signal is sent.
when the 10 min. timer is terminated -
-
(11) Smart key slot detection alert
The SKM sends the smart key slot detection alert signal for 10 sec. when a smart key inserted into
the slot is detected with IGN OFF and the driver's door open. -
(12) SKM alert priority
1 Smart key out alarm Outside
1
2 Smart key reminder alarm Outside
3 Smart key verification failure alarm Inside
2 4 Transponder verification fail alert Inside
5 Smart key battery low voltage alert Inside
6 Transmission position alert Inside
7 SKM error alert Inside
8 Brake alert Inside
9 Clutch alert Inside
10 Smart key slot reminder alarm Inside 1
Warning deactivation conditions
Warning transmission conditions
Warning deactivation conditions
when the smart key is removed, the alert deactivation signal is sent.
when the 10 min. timer is terminated -
-

(2) Standard type LCD instrument cluster display
-
3) GSI(Gear Shift Indication)
Status Standard type Supervision type
Display gear
stage for
manual
transmission
Informs appropriate shift time for manual transmission
: This means that you should shift up to 3rd gear.
(2nd gear or lower currently)
: This means that you should shift down to 3rd gear.
(4th gear or higher currently)
The system operates normally when the indicator lamp looks not being gone out
completely.