light SSANGYONG MUSSO 1998 Workshop Manual PDF

9B-10 LIGHTING SYSTEM
Head Lamp Focusing
When using the beam setting device
1. The head lamp focus should be adjusted by using a proper
beam setting device.
2. Adjust the head lamp focus by using Up/Down, Left/Right
adjusting screws.
When using the screen
1. Put the vehicle on the leveling surface.
2. One person is needed to seat on the driver's seat without
other loads(CVW) and check the tire pressure if it is in the
specification.
3. The distance between the headlamp and the screen is 25m.
4. Draw the vertical line (crossing the center of each headlamp)
on the screen.
5. Start the engine.
6. Check if the cut-off line of the headlamp on the screen is in
the specification.
1) Left/right direction
- The degree of the cross point at the cut-off line of the
headlamp and the vertical line should be 15.
2 ) Up/down direction
- The distance between the cut-off line of the headlamp
and the horizontal line should be 25cm.
7. Adjust the focus if the cut-off line of the headlamp is out of
the specification by using up/down, left/right adjusting
screws.
A : Up/down direction adjusting screw
B : Left/right direction adjusting secrw

LIGHTING SYSTEM 9B-11
Head Lamp
Removal & Installation Procedure
1. Unscrew upper 2(10mm) bolts and lower 1(10mm) bolt of
head lamp.
2. Disconnect connector and remove the headlamp.
3. Installation should follow the removal procedure in the
reverse order.
Bulb Replacement
1. Turn the dust cap of the head lamp to the left and remove
it.
2. If it is high/low head lamp, loosen the screw and pull out the
return spring and replace the bulb.
Notice
For correct installation, check the original position of the
return spring and remove.
High/low-beam head lamp replacement
High-beam head lamp replacement
3. If it is high-beam head lamp, pull out the return spring
and replace the bulb.
Notice
Refern to lamp specifications.

9B-12 LIGHTING SYSTEM
Tail/stop and turn signal lamp
Tail/stop Lamp and backup lamp
Rear Combination Lamp
Removal & Installation Procedure
1. Open the tailgate and remove the inner cover of the rear
combination lamp.
2. Unscrew 4(8mm) nuts of tail/stop lamp and turn signal lamp
assembly.
3. Unscrew 6(8mm) nuts of tail/stop lamp and back-up
lamp assembly.
4. Disconnect each connectors and remove the rear
combination lamp. Replace with specified bulb, if
necessary.
Notice
Refer to lamp specification.

INSTRUMENTATION/DRIVER INFORMATION 9E-3
COMBINATION METER
COMPONENT LOCATOR
1. Speedometer
2. Odometer
3. Trip odometer
4. Tachometer
5. Coolant temperature gauge
6. Fuel gauge
7. Low fuel level warning light
8. Turn signal indicator (left)
9. Turn signal indicator (right)
10. Outside rearview mirror & tailgate heating switch
11. Reset button
12. Auto shift indicator*
13. Door open warning light
14. TCS indicator (equipped with ABD)*
21. ABS warning light*22. EBD warning light*
23. ECS / SPORT warning light*
24. 4 - wheel warning light*
25. 4 - wheel high indicator
26. 4 - wheel low indicator
27. WINTER indicator
28. POWER indicator
29. High beam indicator
15. Alternator warning light
16. Engine oil pressure warning light
17. Brake system warning light
18. Glow indicator light (For Diesel engine)
19. Airbag warning light*
20. Seat belt reminder

9R-4 BODY FRONT END
Adjustment Procedure
1. Alignment between hood striker and latch hole.
lLoosen the mounting bolt of hood latch slightly and adjust
hood in forward/rearward and left/right directions. Then
align the center between hood striker and latch hole.
Notice
Tighten the bolt fully after alignment.
Installation Notice
Tightening Toque 13 - 26 Nm
2. Adjusting the height of hood overslam bumper.
Unlock the hood and check the clearance between hood
and fender by adjusting the hood overslam bumper in left/
right directions.
Normal 20 - 22 Nm
3. Hood Hinge.
lLoosen the hood lock bolts.
lAdjust the lock in forward/rearward and left/right
directions, align with the hood striker and adjust the hood
height.

CONTROL UNITS AND SYSTEM 9U-3
FUNCTION DESCRIPTION
STICS
Operating Functions
NO.ApplicationDeseription
1Wiper INT sensing vehicle speed
lBy operating INT time control volume, variable time will be
changed within 1.5 - 20 seconds.
2Washer relating wiperlWiper begins to operate within 0.6 - 1 sec when the washer
switch is ON and it operates 3 times after the washer switch is
OFF while the IGN2 switch in ON.
3Dimming room lamplWhen room lamp is coupled with door, it turns on if door is
opened. After closing the door it maintains 2 seconds of lighting
and dims off whithin 3 seconds.
4Time delayed power window controllPower window can be operated within 30 seconds after turning
the IGN1 switch from ON to OFF. If driver’s/passenger’s door is
opened within the 30 seconds, time will be prolonged for more
30 seconds from that moment.
5Rear defogger timerlThe rear defogger will be operated for 12 min. by turning ON the
defogger switch while engine is running.
lDefogger will be stopped by pushing the switch again.
lThe defogger will be operated 6 min, if push ON the switch within
10 min. after 12 min. of operation.
6Seat belt warninglThe warning lamp will be turned on for about 6 sec. with an
intermittent chime bell when the IGN. switch is ON unless
fastening the seat belt.
7Parking brake warninglThe indicator lamp will flash if drive while the parking brake is
applied.
8Tail lamp lighting warninglWhen the driver’s door is opened while the tail lamp is still ON,
the buzzer operates intermittently. In this condition, the door will
be automatically unlocked when it locked.
9Door ajar warninglThe indicator lamp will be blinking when the door is not closed
completely and driving.
10IGN key reminderlThe chime will be operated intermittently if the driver’s door is
opened while the IGN key is still remaining in the ignition switch.
In this condition, the door will be automatically unlocked when it
locked.
11Central door locklAll doors will be locked/unlocked by locking/unlocking the
driver’s or passenger’s door.

9U-6 CONTROL UNITS AND SYSTEM
5. Rear defogger timer
T1 : 12±2 min.
T2 : within 10±1 min.
T3 : 6±1 min.
6. Seat belt warning timer
T1 : 6±1 sec.
T2 : 0.3±0.1 sec.
T3 : 0.6±0.1 sec.
7. Parking brake warning
T1 : 0.3±0.1 sec.
T2 : 0.3±0.1 sec.
V1 : 3km/h - 5km/h
8. Tail lamp lighting warning
lWhen the driver’s door is opened after removing the IGN
key while the tail lamp switch is still ON, the buzzer should
be operated.
T1 : 0.3±0.1 sec.
T2 : 0.3±0.1 sec.