air filter SSANGYONG NEW REXTON 2012 User Guide

Engine Compartment Layout
Engine assembly
Engine oil dipstick
Vacuum pump
Oil filter and cooler
Fuel filter and priming pump
Brake booster
Brake oil tank
AQGS unit
Washer fluid filler cap
Engine compartment fuse box
PTC relay box
Battery
Vacuum modulator (for VGT turbo charger) 1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.FFH Assembly (Only for vehicle with FFH)
Power steering oil tank
Engine oil filler cap
Fan shroud
E-EGR Valve
High-capacity PCV oil separator
HFM sensor (6.0)
VGT turbo charger
Air cleaner housing
2Coolant surge tank
ABS/ESP HECU (Including TPMS function:
optional)
Exhaust gas FRT Temp. sensor (T3) 14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.

1212-01
1. D27DT ENGINE STRUCTURE
1) Major Components in Engine and Engine Compartment
The advanced electronically controlled D27DT engine that has high pressure fuel system has
been introduced to this vehicle. It satisfies the strict emission regulation and provides improved
output and maximum torque.
1. Coolant reservoir
2. FFH device
3. Brake fluid reservoir
4. Washer fluid reservoir
5. Common rail6. Fuse box
7. Battery
8. Fuel filter
9. Power steering pump
10. Priming pump11. EGR valve
12. Air cleaner assembly
13. Turbo charger
14. Oil dipstick

2) Engine Structure
1. TVD (Torsional Vibration Damper)
2. Air conditioner compressor
3. Power steering pump pulley
4. Idle pulley
5. Coolant pump pulley
6. Alternator7. Viscos fan clutch
8. Auto tensioner pulley
9. Auto tensioner
10. Poly-grooved belt
11. Cam position sensor
12. Drive plate (MT: DMF)13. Oil filter
14. Vacuum pump
15. Crank position sensor
16. EGR valve
17. Power steering pump
18. EGR to center pipe
Front View
Rear View

2. CDPF(EURO IV) SYSTEM
The CDPF system is only installed to the D27DT engine, and the major changes comparing to the
previous D27DT engine is as follows:
CDPF (Catalyst & Diesel Particulate Filter) and sensors
Under air cleaner in righ
side of engine
compartment
As the soot is filtered in the CDPF, the pressure between the front side and the rear side of the
filter is different from each other. If the amount of soot is over 28 g, the soot is burnt in the
CDPF. The combustion is determined depending on the pressure difference, temperature of
exhaust gas and EGR ratio. According to these, the soot filtered by post injection of injector is
burnt at
CDPF Exhaust Gas Temperature Sensor
The two temperature
sensors inside the CDPF
are installed in exhaust
manifold (front exhaust
gas temperature sensor)
and in DOC (rear exhaust
gas temperature sensor),
and perform the following
functions.Front Exhaust Gas Temperatur
e
Sensor:Rear Exhaust Gas
Temperature Sensor:
Measures the exhaust gas
temperature of the exhaust manifold.
As it is installed in front of the VGT
turbocharger, it also monitors the
exhaust gas temperature coming to
the turbocharger. If the temperature
of the exhaust gas flowing to the
turbocharger is higher than the
specification, the engine lowers the
exhaust gas temperature.Measures the increased
exhaust gas temperature
after the oxidation process
of DOC. If the temperature
injection amount is
increased to increase the
temperature.
Front exhaust gas
temperature sensor

3) Post Injection and Air Mass Control
When the differential pressure sensor detects the pressure difference between the front and the
rear side of CDPF, the sensor sends signal indicating the soot is acumulated and the post
injection is performed to raise the temperature of exhaust gas. The amount of fuel injected is
determined according to the temperature of exhaust gas detected by the rear temperature sensor.
If the temperature is below
the amount of fuel injected is increased to raise the
temperature. If the temperature is over
the amount of fuel injected is decreased or not
controlled.
When the engine is running in low load range, the amount of post injection and the amount of
intake air are controlled. It is to raise the temperature by increasing the amount of fuel while
decreasing the amount of intake air.
2) Sytem Composition for Soot Combustion
When the engine is running in low load range, the temperature of exhaust gas is decreased as the
amount of fuel supplied is decreased. To burn the soot filtered in the CDPF, the control system
should be installed to check the operating range and increase the temperature of exhaust gas by
controlling the amount of fuel supplied and intake air.
Two temperature sensors and one differential pressure sensor monitor the CDPF's operating
range. According to these sensors' information, the throttle flap decreases the intake air entered
to the throttle body. Also, the fuel injection pattern is added to increase the temperature of
exhaust gas for soot combustion.
There are three fuel injection patterns (pilot injection, pre-injection and main injection). As the
CDPF is installed, the post injection pattern is added.

Engine Compartment Layout
Engine assembly
Engine oil dipstick
Vacuum pump
Oil filter and cooler
Fuel filter and priming pump
Brake booster
Brake oil tank
AQGS unit
Washer fluid filler cap
Engine compartment fuse box
PTC relay box
Battery
Vacuum modulator (for VGT turbo charger) 1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.FFH Assembly (Only for vehicle with FFH)
Power steering oil tank
Engine oil filler cap
Fan shroud
E-EGR Valve
High-capacity PCV oil separator
HFM sensor (6.0)
VGT turbo charger
Air cleaner housing
2Coolant surge tank
ABS/ESP HECU (Including TPMS function:
optional)
Exhaust gas FRT Temp. sensor (T3) 14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.