ignition SUBARU BAJA 2003 1.G Owners Manual

Seat, seatbelt and SRS airbags1-7
–
CONTINUED –
Lumbar support
HB1059BA
Pull the lever forward or backward.
Pulling the lever forward will increase the amount of support for yourlower back.
Seat heater (if equipped)
CAUTION
Use of the seat heater for a long period of time while the
engine is not running can cause battery discharge. Do not put anything on the seat which insulates against heat,
such as a blanket, cushion, or similar items. This may cause theseat heater to overheat. When cleaning the seat, do not use benzine, paint thinner, or
any similar materials.
The seat heater operates when the ignition switch is either in the “ACC”
or “ON” position.

Seat, seatbelt and SRS airbags1-17
–
CONTINUED –
This device causes the seatbelt warning light on the instrument panel to
light up for about six seconds when the ignition switch is turned to the
“ON” position to remind the driver to wear the seatbelt. If the driver ’s
seatbelt is not fastened, a warning chime sounds at the same time. Fastening the seatbelt
WARNING
Never use a belt that is twisted or reversed. In an accident, this
can increase the risk or severity of injury. Never place the shoulder belt under the arm or behind the back.
If an accident occurs, this can increase the risk or severity of injury. Keep the lap belt as low as possible on your hips. In a colli-
sion, this spreads the force of the lap belt over stronger hipbones instead of across the weaker abdomen. Seatbelts provide maximum restraint when the occupant sits
well back and upright in the seat. To reduce the risk of sliding un-der the seatbelt in a collision, the front seatbacks should be al-ways used in the upright position while the vehicle is running. Ifthe front seatbacks are not used in the upright position in a colli-
sion, the risk of sliding under the lap belt and of the lap belt slid-ing up over the abdomen will increase, and both can result in se-rious internal injury or death. Do not put cushions or any other materials between occupants
and seatbacks or seat cushions. If you do so, the risk of slidingunder the lap belt and of the lap belt sliding up over the abdomenwill increase, and both can result in serious internal injury ordeath.

1-24
System monitors
HB4010EC
A diagnostic system continually monitors the readiness of the seatbelt
pretensioner while the vehicle is being driven. The seatbelt preten-
sioners share the control module with the airbag system. Therefore, if
any malfunction occurs in a seatbelt pretensioner, the SRS airbag sys-
tem warning light will illuminate. The SRS airbag system warning light
will show normal system operation by lighting for about 6 seconds
when the ignition key is turned to the “ON” position.
The following components are monitored by the indicator: Front sub sensor (Right hand side)
Front sub sensor (Left hand side)
Airbag control module (including impact sensors)
Seatbelt pretensioner (Driver ’s side)
Seatbelt pretensioner (Passenger ’s side)
All related wiring
In the event of a malfunction indicated by any of following, the vehicle
should be taken promptly to your nearest SUBARU dealer to have the
system checked. Unless checked and repaired, the seatbelt preten-
sioners and airbags will not function reliably: Flashing or flickering of the indicator light.
No illumination of the warning light when the ignition switch is
first turned to the “ON” position.
Continuous illumination of the warning light.
Illumination of the warning light while driving.

1-46
SRS airbags deploy as soon as a collision occurs. After deployment, SRS airbags start to deflate immediately so that the driver’s
vision is not obstructed.
OM-H0384
Driver’
s side Passenger ’s side
The SRS airbag can function only when the ignition switch is in the
“ON” position.
If the front sub sensors inside the both front fenders and the impact
sensors in the airbag control module detect a certain predetermined
amount of force during a frontal collision, the control module sends
signals to the frontal airbag modules instructing them to inflate the
SRS frontal airbags. Then both airbag modules produce gas, whichinstantly inflates driver ’s and passenger ’s SRS frontal airbags. After
the deployment, the SRS airbags immediately start to deflate so thatthe driver ’s vision is not obstructed. The time required from detecting
impact to the deflation of the SRS airbag after deployment is shorter
than the blink of an eye.
The front passenger ’s SRS frontal airbag deploys together with driv-
er’ s SRS frontal airbag even when no one occupies the front passen-
ger’ s seat.
When the SRS frontal airbags deploy, the driver ’s and front passen-
ger’ s seatbelt pretensioners operate at the same time.
Although it is highly unlikely that the SRS airbag would activate in a
non-accident situation, should it occur, the SRS airbag will deflate
quickly, not obscuring vision and will not interfere with the driver ’s
ability to maintain control of the vehicle.

1-50
SRS airbag system monitors
HB4010EC
A diagnostic system continually monitors the readiness of the SRS air-
bag system (including front seatbelt pretensioners) while the vehicle is
being driven. The SRS airbag system warning light “AIRBAG” will show
normal system operation by lighting for about 6 seconds when the igni-
tion key is turned to the “ON” position.
The following components are monitored by the indicator: Front sub sensor (Right hand side)
Front sub sensor (Left hand side)
Airbag control module (including impact sensors)
Frontal airbag module (Driver ’s side)
Frontal airbag module (Passenger ’s side)
Seatbelt pretensioner (Driver ’s side)
Seatbelt pretensioner (Passenger ’s side)
All related wiring
In the event of a malfunction indicated by any of following, the vehicle
should be taken promptly to your nearest SUBARU dealer to have the
system checked. Unless checked and repaired, the SRS airbags will not
function reliably: Flashing or flickering of the indicator light.
No illumination of the warning light when the ignition switch is first
turned to “ON” position.
Continuous illumination of the warning light.

2-2
Keys
HS0009
Master keySubmaster keyValet key
Key number plate
Three types of keys are provided for your vehicle.
Master key, submaster key and valet key. The master key and submaster key fit all locks on your vehicle. Ignition switch
Doors
Glove box
The valet key fits only the ignition switch and door locks. You can keep glove box locked when you leave your vehicle and valet key at a parking
facility. Key number
The key number is stamped on the metal plate attached to the key
set. Write down the key number and keep it in another safe place, not
in the vehicle. This number is needed to make a replacement key ifyou lose your key or lock it inside the vehicle.

2-6
Remote keyless entry system (if equipped)CAUTION
Do not expose the transmitter to severe shocks, such as those
experienced as a result of dropping or throwing. Do not take the transmitter apart except when replacing the
battery. Do not get the transmitter wet. If it gets wet, wipe it dry with a
cloth immediately. This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the followingtwo conditions: (1) This device may not cause harmful interfer-
ence, and (2) this device must accept any interference received,including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user ’s authority to
operate the equipment.
Two transmitters are provided for your vehicle.
The keyless entry system has the following functions. Locking and unlocking the doors without a key
Sounding a panic alarm
Arming and disarming the security system (if your vehicle is equipped
with an optional security system). See the next section “Security system
(if equipped) ” for detailed information.
The operable distance of the keyless entry system is approximately 30
feet (10 meters). However, this distance will vary depending on environ-
mental conditions. Range may be reduced near sources of RF interfer-
ence such as power plants and radio/television broadcasting towers.
The keyless entry system does not operate when the key is inserted in the ignition switch.

2-8
LOCK/DISARM” button (for unlocking of all of the doors is ex-
tremely short, the system may not respond. Illuminated entry
The interior (dome) light will illuminate when the “UNLOCK/DISARM”
button is pressed. These lights stay illuminated for approximately 30 seconds if any of the doors is not opened.If the “LOCK/ARM” button is pressed before 30 seconds have
elapsed, these lights will go out. Also, these lights will go out if the key
is inserted in the ignition switch. The interior light must be set to the
middle position in order for this function to operate.
Vehicle finder function
Use this functon to find your vehicle parked among many vehicles in a
large parking lot. Provided you are within 30 feet (10 meters) of the ve-
hicle, pressing the “LOCK/ARM” button three times in a five-second peri-
od will cause your vehicle ’s horn to sound one time and its turn signal
lights to flash three times.
Sounding a panic alarm
To activate the alarm, keep the “LOCK/ARM” button pressed for more
than two seconds .
The horn will sound and the turn signal lights will flash.
To deactivate it, press the “LOCK/ARM” button or “UNLOCK/DISARM”
button. Unless a button on the remote is pressed, the alarm will be
deactivated after approximately 30 seconds. Selecting audible signal operation
Using an electronic chirp, the system will give you an audible signal
when the doors lock and unlock. If desired, you may turn the audible
signal off.
To turn the audible signal off, unlock the doors by pushing “UNLOCK/
DISARM” button and then simultaneously depress “LOCK/ARM” and
“UNLOCK/DISARM” buttons for more than two seconds. An electronic
chirp will sound two times and the turn signal lights will flash two
times to inform you that the audible signal has been turned off.
To turn the audible signal on, unlock the doors by pushing “UNLOCK/

Keys and doors2-11
–
CONTINUED –
HB2032BB
4. Place the ignition key into the ignition switch and cycle the switch
from LOCK to ON ten times within 15 seconds. Be sure to stop at the
LOCK position. The horn will sound once to indicate that you are in
the transmitter programming mode.
NOTE
You must finish the next step (opening the driver ’s door) within
45 seconds of starting this procedures.
To program the transmitters:
HB1000DB
1
2
HB1005BB3 Press any button.
1. Open the driver ’s door.
2. Close the driver ’s door.
3. Press and release any button on the transmitter that you wish to
program into the system. The horn will sound two times to indicate

2-12
that the transmitter has been programmed.
Any additional transmitters can also be programmed at this time.
Repeat steps 1 through 3 for an additional transmitter.
To exit the programming mode:
1. After all of your transmitters are programmed, remove the key fromthe ignition switch.
The horn will sound three times to indicate that the system has exited
the programming mode.
2. Make sure that the keyless entry system properly operates by
operating each transmitter. nDeleting old transmitter codes
The control unit of the keyless entry system has four memory loca-
tions to store transmitter codes, giving it the ability to operate with up
to four transmitters. When you lose a transmitter, the lost transmitter ’s
code remains in the memory. For security reasons, lost transmitter
codes should be deleted from the memory.
To delete old transmitter codes, program four transmitter codes into
the system. If you have only one current transmitter, program it four
times. If you have two current transmitters, program each one twice. If
you have three current transmitters, program two of them once and
the third one twice. This process will leave only current transmittercodes in the system ’s memory.
NOTE
Make sure no one else is operating their keyless entry system within range of your vehicle when programming transmitters. If
someone else were to operate their remote transmitter while youare programming your transmitters, it is possible that their trans-mitter code will be programmed into your system, allowing themunauthorized access to your vehicle.