bulb SUBARU BRZ 2016 1.G Owners Manual

TABLE OF CONTENTSIndex
4
4-1. Maintenance and care
Cleaning and protecting
the vehicle exterior ........... 276
Cleaning and protecting
the vehicle interior ............ 280
Cleaning and protecting
the Alcantara
® area.......... 284
4-2. Maintenance
Maintenance
requirements .................... 286
General maintenance ......... 289
Emission inspection and
maintenance (I/M)
programs .......................... 292
4-3. Do-it-yourself
maintenance
Do-it-yourself service
precautions ...................... 293
Engine hood ....................... 296
Engine compartment .......... 298
Tires ................................... 312
Tire inflation pressure......... 319
Wheels ............................... 323
Air conditioning filter ........... 326
Transmitter/
access key battery ........... 329
Checking and
replacing fuses ................. 334
Light bulbs .......................... 3425-1. Essential information
Hazard warning flashers ..... 358
If your vehicle needs to
be towed ........................... 359
If you think something
is wrong ............................ 366
Fuel pump shut off
system .............................. 367
5-2. Steps to take in an
emergency
If a warning light turns
on or a warning buzzer
sounds... .......................... 368
If you have a flat tire ........... 382
If the engine will not
start .................................. 393
If the select lever cannot be
shifted from P ................... 396
If you lose your keys ........... 397
If the access key does not
operate properly ............... 398
If the battery is
discharged ........................ 402
If your vehicle
overheats .......................... 407
If the vehicle becomes
stuck ................................. 410
4Maintenance and care5When trouble arises

184
2-1. Driving procedures
Turn signal lever
■Turn signals can be operated when
Vehicles without a keyless access with push button start system
The engine switch is in the “ON” position.
Vehicles with a keyless access with push button start system
The push-button ignition switch is in “ON” mode.
■If the indicators flash faster than usual
Check that a light bulb in the turn signal lights has not burned out. The turn signal lever can be used to show the following intentions of
the driver:
Right turn
Left turn
Lane change to the right
(push and hold the lever
partway)
The right hand signals will
flash until you release the
lever.
Lane change to the left
(push and hold the lever
partway)
The left hand signals will flash
until you release the lever.

Maintenance and care4
275
4-1. Maintenance and care
Cleaning and protecting
the vehicle exterior......... 276
Cleaning and protecting
the vehicle interior.......... 280
Cleaning and protecting
the Alcantara
® area ....... 284
4-2. Maintenance
Maintenance
requirements .................. 286
General maintenance....... 289
Emission inspection and
maintenance (I/M)
programs........................ 2924-3. Do-it-yourself
maintenance
Do-it-yourself service
precautions .................... 293
Engine hood ..................... 296
Engine compartment ........ 298
Tires ................................. 312
Tire inflation pressure ...... 319
Wheels ............................. 323
Air conditioning filter......... 326
Transmitter/access key
battery ............................ 329
Checking and replacing
fuses .............................. 334
Light bulbs........................ 342

294 4-3. Do-it-yourself maintenance
ItemsParts and tools
Light bulbs (oP. 342)• Bulb with same number and watt-
age rating as original
• Phillips-head screwdriver
• Flathead screwdriver
Radiator and condenser
(oP. 304)

Tire inflation pressure (oP. 319)• Tire pressure gauge
• Compressed air source
Washer fluid (oP. 310)• Water washer fluid containing anti-
freeze (for winter use)
• Funnel

341 4-3. Do-it-yourself maintenance
4
Maintenance and care
■After a fuse is replaced
●If the lights do not turn on even after the fuse has been replaced, a bulb
may need replacement. (oP. 342)
●If the replaced fuse blows again, have the vehicle inspected by your
SUBARU dealer.
■If there is an overload in the circuits
The fuses are designed to blow, protecting the wiring harness from damage.
WARNING
■To prevent system breakdowns and vehicle fire
Observe the following precautions.
Failing to do so may cause damage, and possibly a fire or injury.
●Never use a fuse of a higher amperage rating than indicated, or use any
other object in place of a fuse.
●Always use a genuine SUBARU fuse or equivalent.
●Do not modify the fuse or the fuse box.
CAUTION
■Before replacing fuses
Have the cause of electrical overload determined and repaired by your
SUBARU dealer.

342
4-3. Do-it-yourself maintenance
Light bulbs
You may replace the following bulbs by yourself. The difficulty level
of replacement varies depending on the bulb. If necessary bulb
replacement seems difficult to perform, contact your SUBARU
dealer.
■Preparing a replacement light bulb
Check the wattage of the light bulb being replaced. (oP. 425)
■Front bulb locations
Front side
marker lights
Front turn signal lights
Front fog lights (if equipped)

343 4-3. Do-it-yourself maintenance
4
Maintenance and care
■Rear bulb locations
■Inside bulb locations
Rear turn signal lights
Rear side marker lights
Back-up lightsLicense
plate
lights
Interior light
Vanity lights
(if equipped)

344 4-3. Do-it-yourself maintenance
Replacing light bulbs
■Front turn signal lights
Turn the bulb base counterclock-
wise.
Remove the light bulb.
When installing, reverse the steps listed.
STEP 1
STEP 3 STEP 2
STEP 3

346 4-3. Do-it-yourself maintenance
Remove the light bulb.
When installing, reverse the steps listed.
■Front fog lights (if equipped)
Turn the steering wheel in the
opposite direction of the light to
be replaced.
Turn the steering wheel to a point
that allows your hand to easily fit
between the tire and fender liner.
Remove the clips and partly
remove the fender liner.
To prevent damage to the vehicle,
cover the tip of the screwdriver
with a rag.
STEP 5
STEP 6
STEP 1
STEP 2

347 4-3. Do-it-yourself maintenance
4
Maintenance and care
Unplug the connector while
depressing the lock release.
Remove the light bulb.
When installing, reverse the steps listed.STEP 3
STEP 4
STEP 5