check engine SUBARU FORESTER 2000 SF / 1.G User Guide

10-4
Always use the proper tools and make certain that they are
well maintained. Never get under the vehicle supported only by a jack. Always
use a safety stand to support the vehicle. Never keep the engine running in a poorly ventilated area,
such as a garage or other closed areas. Do not smoke or allow open flames around the fuel or battery.
This will cause a fire. Wear adequate eye protection to guard against getting oil or
other fluids in your eyes. If something does get in your eyes,
thoroughly wash it out with clean water. Because the fuel system is under pressure, replacement of the
fuel filter should be performed only by your SUBARU dealer. The SRS airbag has no user-serviceable parts. Tampering with
or disconnecting the system ’s wiring could result in accidental
inflation of the airbag or could make the system inoperative,
which may result in serious injury. The wiring harnesses of theSRS airbag system are covered with yellow insulation and the
connectors of the system are yellow, for easy identification. Donot use electrical test equipment on any circuit related to the SRSairbag system. For required servicing of the SRS airbag, see your
nearest SUBARU dealer. Before checking or servicing in the engine compartment
Always stop the engine and set the parking brake firmly to pre-
vent the vehicle from moving. Always let the engine cool down. Engine parts become very
hot when the engine is running and remain hot for some time af-ter the engine is stopped. Do not spill engine oil, engine coolant, brake fluid or any other
fluid on hot engine components. This may cause a fire. Always remove the key from the ignition switch. When the
ignition switch is in the “ON” position, the cooling fan may oper-
ate suddenly even when the engine is stopped.

Maintenance and service10-5
–
CONTINUED –

When you do checking or servicing in the engine
compartment while the engine is running
A running engine can be dangerous. Keep your fingers, hands, clothing, hair and tools away from the cooling fan, belts and anyother moving engine parts. Removing rings, watches and ties isadvisable.

Maintenance and service10-7
–
CONTINUED –
Engine oil
Checking the oil level
Chec k the eng ine oil level at eac h fuel stop .
OM-H2727
HS0173
Upper level
Lower- level Notch
front
1. Park the vehic le on a level surfac e and stop the eng ine.
2. Pull out the d ip stic k, wip e it c lean, and insert it ag ain.
3. Be sure the d ip stic k is c orrec tly inserted until it stop s with the
g rap hic symb ol on its top ap p earing as shown in the illustra-
tion.
4. Pull out the d ip stic k ag ain and c hec k the oil lev el on it. If it is b elow
the lower level, ad d oil to b ring the level up to t he up p er level.
CAUTION
Use only engine oil with the recommended grade and viscosity.
If you c hec k the oil level just after stop p ing the eng ine, wait a few min-
utes for the oil to d rain b ac k into the oil p an b ef ore c hec king the level.
Just after d riving or while the eng ine is warm, the eng ine oil level
read ing may b e in a rang e b etween the up p er level a nd the notc h
mark. This is c aused b y thermal exp ansion of the en g ine oil.
To p revent overfilling the eng ine oil, d o not ad d a ny ad d itional oil
ab ove the up p er level when the eng ine is c old .

Maintenance and service10-13
–
CONTINUED –

Engine coolant Checking the coolant level
Chec k the c oolant level at eac h fuel stop .
HS0178
“FULL”
level mark
“LOW” level mark
1. Chec k the c oolant level on the outsid e of the res ervoir while the
eng ine is c ool.
2. If the level is c lose to or lower than the “LOW ” level mark, ad d
c oolant up to the “FULL ” level mark. If the reserve tank is emp ty, re-
move the rad iator c ap and refill as req uired .
HG0115
Rubber gaskets
3. After refilling the reserve tank and the rad iator , reinstall the c ap s
and c hec k that the rub b er g askets insid e the rad iat or c ap are in the
p rop er p osition.