SUBARU FORESTER 2000 SF / 1.G Owner's Guide

1-12
HS1003BB
HS1002BA
1. Remove the p hillip s sc rew on the b ac k of the remo te transmitter
c ase. Use a small c oin to sep arate the c ase halves and exp ose the
b attery.
2. Remove the old b attery and rep lac e with typ e GP-2 3A or eq uiva-
lent.
3. Close the transmitter c ase and rep lac e the sc rew.
Security system (if equipped) How the security system protects your vehicle
n Starter interrupt
The vehic le ’s starter is d isab led when the system is armed with your
remote transmitter. n Passive starter interrupt (if selected)
The vehic le starter is automatic ally d isab led one m inute after the ig ni-
tion is turned off, even if the system has not been armed with your
remote transmitter . (This op tion may b e ac tivated b y your SUBARU
d ealer for an ad d itional c harg e.) NOTE
If the Passive Starter Interrupt Option is enabled on your system, pay special attention to the “Starter interrupt ” section.

Doors and locks1-13
–
CONTINUED –
n
All entrances protected
Op ening any d oor or entranc e p rotec ted b y the sec ur ity system trig -
g ers the alarm ’s 125 d b siren and flashes the vehic le ’s p arking lig hts.
n Shock Sensor
The shoc k sensor d etec ts any imp ac t to the vehic le. Lig ht imp ac t will
c ause the siren to emit a warning “c hirp ”; heavier b lows will trig g er
the alarm. (Shoc k sensor sensitivity has b een p rese t, b ut may b e
ad justed b y your SUBARU d ealer.) n Personal protection (Panic) feature
Pressing b oth b uttons on the remote transmitter ac t ivates the Panic
feature, sound ing the siren and flashing the vehic l e’s p arking lig hts.
n Interior status indicator
The b rig ht-red warning lig ht p rovid es a visual d ete rrent to a would -b e
thief.n Emergency override button
Ensures that you will b e ab le to d isarm your alarm system and start
your vehic le if your remote transmitter is lost or b roken. See “The
emerg enc y overrid e/p rog ramming b utton ” Sec tion.
Security system components
n The remote Transmitter
The remote transmitter c ontrols the features and op tions of the sec u-
rity system.
HS1000CB

1-14The sec urity system c an b e p rog rammed to op erate wi
th one to four
remote transmitters. Eac h transmitter is p owered b y an internal 12-volt
alkaline b attery. n The status indicator/Valet button
HS1004BB
The Status Ind ic ator is a hig h intensity warning li g ht, loc ated on the
d ash to the left of the steering wheel. The Status Ind ic ator d isp lays a
visual ind ic ation of the sec urity system ’s status while c reating a p ow-
erful theft d eterrent. LED status Off: System is d isarmed .
Double-Flash: System is in valet mod e.
Steady Flash: System is armed .
Fast Flash: System has b een trig g ered .
On: System is in p re-arm state (and will arm when all d oors are
c losed ). n The valet button (built into the status indicator)
The Valet Button is used to eng ag e Valet Mode (see “Valet mod e ”
Sec tion). In Valet Mod e, the sec urity system will n ot arm, throug h the
siren will c hirp and keyless entry features will fu nc tion when the sec u-
rity system is d isarmed .

Doors and locks1-15
–
CONTINUED –
n
The emergency override/programming button
HS1001BC
The Emerg enc y Overrid e/Prog ramming b utton is used t o d isarm the
alarm system in c ase of a lost or b roken transmitte r. It is also used in
c onjunc tion with the transmitter and vehic le ig niti on to p rog ram ad d i-
tional transmitters. The Emergency Override Button is located under the driver ’s side
dash beneath the diagnostic connector. Security system operation
IMPORTANT Security System and Keyless Entry Features Do Not Operate
when the Vehicle Ignition is on.

1-16n
Arming the system
HS1000DB
To arm the system, c lose all d oors, then p ress the “LOCK ” b utton. The
siren will “c hirp ” twic e and the p arking lig hts will flash twic e, ind ic at-
ing the system is armed .
The d oors will also loc k at this time. The status i nd ic ator will b link
stead ily, onc e p er sec ond .
If the siren c hirp s and /or the lig hts flash only once, this ind ic ates that
the system is in pre-arm mode. The system has d etec ted that a p ro-
tec ted entranc e is not sec ured . In p re-arm mod e, th e status ind ic ator
stays on and d oes not b link. Chec k to see that all vehic le entranc es
are c losed sec urely. Onc e all entranc es are sec ured , the system will
c hirp /flash ag ain, and the status ind ic ator will b l ink stead ily. The sys-
tem is now fully armed .

Doors and locks1-17
–
CONTINUED –
n
Disarming the system
HS1000EB
To d isarm the system, p ress and release the “UNLOCK ” b utton. The
siren will c hirp and p arking lig hts will flash once. The d river ’s d oor will
unloc k at this time, and the vehic le interior (d ome ) lig ht will turn on for
60 sec ond s, or until the vehic le is started .
If the siren c hirp s and p arking lig hts flash four times, the system was
trig g ered in your ab senc e. Refer to the “Trip identification ” sec tion in
this manual. n The alarm cycle
If your alarm system is trig g ered , the siren will s ound and the p arking
lig hts will flash for 60 sec ond s. After this d urati on, the system will
c hec k to see if an entranc e was left op en. If so, t he alarm will c ontinue
to sound . If not, the system will re-arm.

1-18n
Personal protection alarm (Panic)
HS1000BC
Pressing b oth b uttons tog ether on the remote transm itter ac tivates the
Panic feature, sound ing the siren and flashing the p arking lig hts.
Panic is d esig ned to b ring attention to the vehic le and surround ing
area. Press either b utton on the transmitter to tur n off the Panic alarm.
n Disarming the security system in the event of a lost or broken transmitter
HS1001CB
If your remote transmitter fails to op erate, the sy stem c an b e d is-
armed using the Emerg enc y Overrid e/Prog ramming b utt on. Follow
the p roc ed ure b elow:
1. Enter the vehic le. The alarm will sound when the d oor is op ened .
2. Insert the ig nition key and turn to the “ON ” p osition.

Doors and locks1-19
–
CONTINUED –
3. Press the Emerg enc y Overrid e/Prog ramming b utton.
The system
will d isarm. n Valet mode
HS1004CB
Valet Mod e p revents the sec urity system from arming , yet allows all
keyless entry and c onvenienc e features to func tion normally.
The valet b utton is b uilt into the status ind ic ator , loc ated on the d ash
to the left of the steering wheel.
To eng ag e Valet Mod e: With the system d isarmed and the vehic le ig nition o ff, p ress the
Status Ind ic ator/Valet Button. The status ind ic ator will b eg in to emit a q uic k d ou b le-flash p attern.
This ind ic ates that the system is in Valet Mod e. To exit Valet Mod e, p ress the Status Ind ic ator/Vale t Button ag ain.
The status ind ic ator will turn off, ind ic ating the system is in normal
op erating mod e. n Trip identification
If the siren c hirp s four times when you d isarm your sec urity system,
this ind ic ates that the system was trig g ered in you r ab senc e. Before
turning the ig nition on, p erform the following op er ation to d etermine
the p rotec ted zone that trig g ered the system. Op en the vehic le d oor and p ress the Emerg enc y Overr id e/Pro-
g ramming b utton.

1-20
The siren will emit a numb er of c hirp s. Refer to th e c hart (b elow) to
id entify the violated zone.

Chirps
Triggered Zone


1



Shock Sensor

2
Ignition turned on

4
Door or Rear gate
n
Starter interrupt
Starter interrup t is an automatic p roc ed ure. The st arter is d isab led
any time the system is armed , or if the Passive starter interrup t fea-
ture is enab led and the p assive arm time is exp ired . The vehic le also
will not start if p ower is d isc onnec ted from the al arm mod ule.
How starter interrupt works
The alarm system interrup ts the sig nal from the ig n ition key to the
vehic le ’s starter when Starter interrup t is ac tivated . If y ou attemp t to
start the vehic le, the d ash ind ic ator will turn on as usual, b ut the
starter will not “c rank ”, or turn over.
Passive starter interrupt
If the Passive Starter Interrup t op tion has b een ac tivated b y you r
SUBARU d ealer, the starter will b e automatic ally d i sab led one minute
after you turn off the vehic le ig nition, whether or not you arm the sec u-
rity system with your remote transmitter.
Possible situations with starter interrupt or Passive starter inter-
rupt
Passive Starter Interrupt
If you leave the vehic le for a short amount of time , to refuel or g o to
the c ar wash for examp le, always eng ag e the Valet M od e b efore exit-
ing your vehic le. If you forg et to eng ag e Valet Mod e, the Passive
Starter Interrup t will eng ag e and the vehic le will not start when you
return. To enable the vehicle to start, simply press “UNLOCK” on

Doors and locks1-21
–
CONTINUED –
your remote transmitter, or turn the vehicle ignition to the
“ON”
position and press the Emergency Override/programming button in and release .
If your remote transmitter is lost or b roken and th e Passive Starter
Interrup t has automatic ally eng ag ed , enter the vehi c le, turn the ig ni-
tion to the “ON ” p osition, and p ress the Emerg enc y Overrid e/p ro-
g ramming b utton. This will enab le the vehic le to st art.
In the unlikely event of an alarm system malfunc tio n, your vehic le
may not start. To enab le the vehic le to start, press and hold the
Emergency Override/programming button, and attempt to startthe vehicle while holding the button in .
System maintenance
Your sec urity system d oes not req uire any sp ec ific maintenanc e
exc ep t for oc c asionally c hang ing the transmitter b a ttery. However, it is
sug g ested that the system b e armed and all p rotec te d zones b e
c hec ked ab out onc e a month to make sure that they t rig g er an alarm
c yc le.
To c hang e the remote transmitter b attery, refer to “System mainte-
nanc e ” sec tion und er the head ing of “Keyless entry system ”.
Trouble shooting guide
n If you experience any of the following situations...
Your remote transmitter is lost or broken and your alarm sys-
tem is armed. You attempt to start your vehicle after pressing “UNLOCK” on
your remote transmitter and it does not “crank”.
Perform the following procedure:
1. Use your keys to enter the vehicle. (Depending on your situa-
tion, the alarm may sound when you open the door.)
2. Insert your key into the ignition and turn to the “ON” position.
3. Press and release the Emergency Override Button. The alarm
system will disarm and you will be able to start your vehicle.
4. If your vehicle still will not start, press and HOLD the Emer-gency Override Button in while attempting to start your vehicle.