lights SUBARU FORESTER 2003 SG / 2.G Owner's Manual

3-28
Instruments and controls
Automatic climate control system
The rear window defogger operates only when the ig-
nition switch is in the “ON” position.
The rear window defogger switch is located on the cli-
mate control panel.
The defogger will automatically shut off after about 15
minutes. If the window clears before that time, push
the switch to turn it off. It also turns off when the igni-
tion switch is turned to the “ACC” or “LOCK” position.
If defrosting or defogging is desired when you restart
your vehicle, you have to push the switch to turn it on
again.
To turn on the defogger, push the switch. To turn it off, push the switch again.
The indicator light located on the switch lights up while
the rear window defogger is operating.

Do not use sharp instruments or window
cleaner containing abrasives to clean the inner
surface of the rear window. They may damage
the conductors printed on the window. To prevent the battery from being dis-
charged, do not operate the defogger continu-
ously for any longer than necessary.HS4021DA

3-29
Instruments and controls
–CONTINUED –
Mirrors
Always check that the inside and outside mirrors are
properly adjusted before you start driving. Inside mirror
1) Tab
The inside mirror has a day and night position. Pull the
tab at the bottom of the mirror toward you for the night
position. Push it away for the day position. The night
position reduces glare from headlights.
Auto-dimming mirror/com pass (if equipped)
1) Left button
2) Auto dimming indicator
3) Photosensor
4) Right button
The inside electronic compass mirror has an anti-glare
feature which automatically reduces glare coming
from headlights of vehicles behind you. It also con-
tains a built-in compass. By pressing and releasing the left button, the auto-
matic dimming function is toggled on or off. When the
automatic dimming function is on, the auto dimming in-
dicator light (green) located to the right of the button
1HS3036BB
1
23 4
HS3037BB

3-30
Instruments and controls
will illuminate.
By pressing and releasing the right button, the com-
pass display is toggled on or off. When the compass is
on, an illuminated compass reading will appear in the
lower part of the mirror.
Even with the mirror in anti-glare mode, the mirror sur-
face turns bright if the transmission is shifted into re-
verse. This is to ensure good rearward visibility during reversing. Photosensors
The mirror has a photosensor attached on both the
front and back sides. If the glare from the headlights of
vehicles behind you strikes the mirror, these sensors detect it and make the reflection surface of the mirror
dimmer to help prevent you from being blinded. For
this reason, use care not to cover the sensors with
stickers, or other similar items. Periodically wipe the
sensors clean using a piece of dry soft cotton cloth or
an applicator.
Compass calibration
1. For optimum calibration, switch off all nonessential
electrical accessories (rear window defogger, heater/
air conditioning system, spotlight, etc.) and ensure all
doors are shut.
2. Drive to an open, level area away from large metal-
lic objects or structures and make certain the ignition
switch is in the “ON” position.
3. Press and hold the left button for 3 seconds then re-
lease, and the compass will enter the calibration
mode. “CAL” and direction will be displayed.
4. Drive slowly in a circle until “CAL” disappears from
the display (about two or three circles).
5. The compass is now calibrated. Further calibration
is not required. The compass will automatically cali-
brate from this point forward.
HS3038BA

3-32
Instruments and controls
determine the actual size and distance of ob-
jects that you view in convex mirror.
Remote control mirror switch
1) Selection switch
2) Direction control switch
The remote control mirrors operate only when the ig-
nition switch is in the “ON” or “ACC” position.
1. Press either end of the selection switch, “L” for the
left, “R” for the right.
2. Move the direction control switch in the direction
youwanttomovethemirror. 3. Return the selection switch to the neutral position
to prevent unintentional operation.
The mirrors can also be adjusted manually.
Outside mirror defogger
1) Outside mirror defogger switch (if equipped)
2) Outside mirror defogger and Windshield wiper deicer switch (if equipped)
The outside mirror defogger operates only when the
ignition switch is in the “ON” position.
To turn on the outside mirror defogger, push the
switch. To turn it off, push the switch again. The indi-
cator light located on the switch lights up while the out-
MIRRMIRROROR
LR1
2
HS3041BB
12
HS3046AB

4-12
Climate control
Manual mode operation:
If you operate any of the switches and dials on the
control panel other than the “OFF” switch and temper-
ature control dial during automatic mode operation,
the indicator light on the “AUTO” switch goes out. You
can then manually control the system as desired using
the switch or dial you operated.
To change the system back to the AUTO mode, press
the “AUTO” switch.
OFF switch
The Automatic Climate Control system turns off (the
air conditioner compressor and fan turn off) when the
“OFF” switch is pressed.
When the “OFF” switch is pressed, the outside air in-
troduction mode (air inlet selection OFF) is automati-
cally selected.
NOTE
Display illumination dimness cancellation (BRIGHT):
Setting the light switch to the “ ” or “ ”
position causes the illumination on the display
panel to dim. When traveling with the lights on in
gloomy daylight or in twilight, press the OFF
switch for 1 second or longer if you feel it is too
hard to identify the illumination clearly. The bright-
ness comes back to normal. If you wish to dim the illumination again, hold
down the OFF switch again or if you can safely do
so, turn the light switch OFF and then place it in
the “ ” or “ ” position.
Temperature control dial
This dial is used to set the desired interior tempera-
ture. With the dial is set your desired temperature, the
system automatically adjusts the temperature of air
supplied from the outlets such that the desired temper-
ature is achieved and maintained.
If the dial is turned fully counterclockwise, the system
gives maximum cooling performance. If the dial is
turned fully clockwise, the system gives maximum
heating performance.

5-27
Audio
– CONTINUED –
NOTE
Make sure to always insert a disc with the label
side up. If a disc is inserted with the label side
down, it might be ejected or the player might shut off. How to insert a CD(s)
Inserting a CD
1. Press “LOAD” button (18). If the magazine in the
player has an idle position where you can insert a disc,
the “DISC” indicator associated with the idle position
will blink.
If no indicator blinks, it means that there is no idle po-
sition in the magazine.
2. As soon as the “DISC” indicator begins to blink, the
“IN” will appear on display for a period of 15 seconds.
Insert a disc during the period. The disc will be then
automatically drawn in, and the player will begin to
play back the first number of the disc. To insert more discs in succession, repeat Steps 1
and 2. The magazine will be loaded with discs in the
ascending order of position number.
If you do not insert any disc in 15 seconds after you
have pressed the “LOAD” button, the player will begin
to play back the first number of the last disc you have
inserted.
The disc indicator steadily lights up if a disc is al-
ready inserted in the corresponding position of the
magazine. While the player is in the loading mode, if you press
any of the other mode buttons “FM/AM” (1), “WB” (2)
and “TAPE” (12), the player will enter the standby
mode. Press the “CD” button (21) to start playback. Inserting a disc in a desired position
1. Press the “LOAD” button. If the magazine in the
player has an idle position where you can insert a disc,
the “DISC” indicator associated with the idle position
will blink.
The positions in the magazine the indicator of which
steadily lights up are already loaded with discs.
2. Press the “DISC SELECT” button (26) at the posi-
tion where you want to insert a disc. The associated
“DISC” indicator will blink, and the “IN” will be dis-
played.
3. If you insert a disc during the 15-second period
while the “IN” is on display, the disc will be automati-
cally drawn in, and the player will start playback of the
disc, beginning with the first number. To insert more discs in succession, repeat Steps 1
and 2. While the player is in the loading mode, if you press
any of the other mode buttons “FM/AM” (1), “WB” (2)

5-28
Audio
and “TAPE” (12), the player will enter standby mode.
Press the “CD” button to start playback.
Loading all the magazine (Full disc loading mode)
1. If you continue to press the “LOAD” button for more
than 1.5 seconds, the player will produce beep sound
and will enter the full disc loading mode.
2. A “DISC” indicator will blink, and the “IN” will be on
display for a period of 15 seconds. If a disc is success-
fully loaded during this period, the “DISC” indicator will
stop blinking and will steadily light.
3. When the loading of a disc is complete, the next
“DISC” indicator will blink. Then repeat Step 2.
4. When the magazine is filled with discs by repeating
Steps 2 and 3, the player will start playback of the
discs, beginning with the one inserted first.
If you fail to insert any disc during each 15-second in-
terval, the full disc loading mode will be canceled, and
the player will start playback of the disc inserted first. How to play back a CD or make a pause
When there is no CD inserted:
Insert a CD by referring to “How to insert a CD(s)”.
When a CD is loaded, the player will start playback of
the CD, beginning with the first number.
When there are CDs loaded:
Press a desired one of the “DISC SELECT” buttons
(26) the “DISC” indicator of which steadily lights up.
The player will then start playback of the selected CD,
beginning with the first number. Selecting a desired track (TRACK)
: Skipping forward
: Skipping backward
: Fast forwarding
: Fast reversing
Skipping forward
Turn the “TRACK” knob (24) clockwise and release it
HS5015BA

5-32
Audio

Donotattempttoinserttwoormorediscs
into the slot at a time. Doing so can cause me-
chanical damage to the CD changer. Use only music CDs identified by
am ark .
Do not use CDs listed below which could
cause damage to the CD player.
3-inch (8 cm) compact disc.
Any disc with a peel-off or seal on it.
Any disc with scratches and/or dust.
Bent disc.
Cleaning disc.
CD accessory. (E.g., 3-inch (8 cm) disc
adapter)
Do not insert or remove any disc when the
automatic transmission selector lever is in the
park position; the selector lever in that position
can interfere with disc insertion or removal,
causing scratches on the disc surface (for AT
vehicles).
To insert a disc
1. Press one of the “Disc select” buttons (3) (num-
bered from 1 to 6) for which the disc indicator light (2) is “OFF”.
The Disc indicator lights are located directly above the
corresponding “Disc select” buttons.
2. The indicator will begin blinking. The blinking will
last for 15 seconds.
During this period, insert a desired disc, and the disc
will begin to play. (If any disc is not inserted during this
period, the “Disc slot” (1) door will close. Repeat step
1.)
Be sure to hold a disc with the label side (the side
where titles are printed) up.
3. To insert another disc, repeat step 1 and 2 choos-
ing a different disc select button.
To insert six discs at a time
1. Press and hold the “Disc select” button number 1
until all disc indicators begin blinking (about 1.5 sec- onds).
2. The indicators will blink for 15 seconds. During this
period, insert desired six discs.
3. When all discs are loaded, the first disc will begin to
play. (If no disc is inserted within this 15 seconds, the
entire disc load sequence will be canceled.) To remove a disc
1. Press the desired one of the “Disc select” buttons
(3) (numbered from 1 to 6) for which the disc indicator
light is on.

6-1
6
Interior equipment
Interior lights ............................................... 6-2 Dome light ....................................................... 6-2
Cargo area light .............................................. 6-2
Map lights ..................................................... 6-3
Sun visors .................................................... 6-3 Vanity mirror .................................................... 6-4
Storage compartments ............................... 6-4 Glove box ......................................................... 6-5
Center console ................................................ 6-5
Overhead console ........................................... 6-6
Dashboard storage compartment ................. 6-6
Convenience net ............................................. 6-7
Coin tray .......................................................... 6-7
Cup holders ................................................. 6-8 Front passenger

6-2
Interior equipment
Interior equipment
Interior lights
When leaving your vehicle, make sure the light goes
out to avoid battery discharge.
Dome light
The dome light switch has three positions: ON: The light stays on continuously.
DOOR (middle position): The dome light comes on
when any of the doors or the rear gate is opened. The
light remains on for several seconds and gradually
goes out after all doors and the rear gate are closed or
if the key is inserted in the ignition switch. The light also can be turned on by use of the keyless
entry transmitter. See the “Remote keyless entry sys-
tem (if equipped)” in chapter 2 for detailed information.
OFF:
The light stays off.
Cargo area light
The cargo area light switch has three positions: ON: The light stays on continuously.
OFF: The light stays off.
DOOR: The light comes on only when the rear gate is
opened.
ON
DOOR
OFF
HS6025BB
ON
OFF
DOOR
HS6026BB