tow SUBARU FORESTER 2006 User Guide

Page 127 of 355

3-14
Instruments and controls
tions of the brake system are still avail-
able. You will be safe while driving with
this condition, but have your vehicle
checked at a SUBARU dealer as soon as
possible.NOTEIf the warning light behavior is as
shown in the following, the Vehicle Dy-
namics Control system may be consid-
ered normal.
yThe warning light comes on right af-
ter the engine is started but goes out
immediately, remaining off.
y The warning light comes on after en-
gine startup and goes off while the ve-
hicle is subsequently being driven.
y The warning light comes on during
driving, but it goes out immediately
and remains off.
T Vehicle Dynamics Control OFF indi-
cator light
y It comes on when the Vehicle Dynamics
Control OFF switch is pressed.
y It also comes on when the Vehicle Dy-
namics Control system is deactivated.NOTEy The light may stay on for a while after
the engine has been started, especially
in cold weather. This does not indicate
the existence of a problem. The light should go out as soon as the engine
has warmed up.
y
The indicator light comes on when
the engine has developed a problem
and the Malfunction indicator light is
on.
The Vehicle Dynamics Control system is
probably faulty under the following condi-
tion. Have your vehicle checked at a
SUBARU dealer as soon as possible.
y The light does not go out even after the
lapse of several minutes (the engine has
warmed up) after the engine has started.
„ Brake system
warning light
This light has the following three func-
tions:
T Parking brake warning
The light comes on with the parking brake
applied while the ignition switch is in the
“ON” position. It goes out when the park-
ing brake is fully released.
T Brake fluid level warning
This light comes on when the brake fluid
level has dropped to near the “MIN” level
of the brake fluid reservoir with the ignition
switch in the “ON” position and with the
parking brake fully released.
If the brake system warning light should
come on while driving (with the parking
brake fully released and with the ignition
switch positioned in “ON”), it could be an
indication of leaking of brake fluid or worn
brake pads. If this occurs, immediately
stop the vehicle at the nearest safe place
and check the brake fluid level. If the fluid
level is below the “MIN” mark in the reser-
voir, do not drive the vehicle. Have the ve-
hicle towed to the nearest SUBARU deal-
er for repair.
T Electronic Brake Force Distribution
(EBD) system warning (vehicles
with EBD)
The brake system warning light also illu-
y Driving with the brake system
warning light on is dangerous.
This indicates your brake system
may not be working properly. If
the light remains on, have the
brakes inspected by a SUBARU
dealer immediately.yIf at all in doubt about whether the
brakes are operating properly, do
not drive the vehicle. Have your
vehicle towed to the nearest
SUBARU dealer for repair.
(U.S.)
(Canada)
ProCarManuals.com

Page 128 of 355

Instruments and controls
3-15
– CONTINUED –
minates if a malfunction occurs in the EBD
system. In that event, it comes on together
with the ABS warning light.
The EBD system may be malfunctioning if
the brake system warning light and ABS
warning light illuminate simultaneously
during driving.
Even if the EBD system fails, the conven-
tional braking system will still function.
However, the rear wheels will be more
prone to locking when the brakes are ap-
plied harder than usual and the vehicle’s
motion may therefore become somewhat
harder to control.
If the brake system warning light and ABS
warning light illuminate simultaneously,
take the following steps:
1. Stop the vehicle in the nearest safe, flat
place.
2. Shut down the engine, then restart it.
3. Release the parking brake. If both
warning lights go out, the EBD system
may be faulty.
Drive carefully to the nearest SUBARU
dealer and have the system inspected.
4. If both warning lights come on again
and stay illuminated after the engine has
been restarted, shut down the engine
again, apply the parking brake, and check
the brake fluid level.
5. If the brake fluid level is not below the
“MIN” mark, the EBD system may be faulty. Drive carefully to the nearest
SUBARU dealer and have the system in-
spected.
6. If the brake fluid level is below the
“MIN” mark, DO NOT drive the vehicle. In-
stead, have the vehicle towed to the near-
est SUBARU dealer for repair.

Door open warning lightsThe door open warning light comes on if
any door or the rear gate is not fully
closed.
Always make sure this light is out before
you start to drive.„Low fuel warning light The low fuel warning light comes on when
the tank is nearly empty [approximately
2.3 US gal (9.0 liters, 1.9 Imp gal)]. It only
operates when the ignition switch is in the
“ON” position.NOTEThis light does not go out unless the
tank is replenished up to an internal
fuel quantity of approximately 4.0 US
gal (15 liters, 3.3 Imp gal).
„All-Wheel Drive warn-
ing light (AT vehicles)The All-Wheel Drive indicator light comes
on when the ignition switch is turned to the
“ON” position and goes out after the en-
gine has started.
T For vehicles with Vehicle Dynamics
Control system
This light flashes if the vehicle is driven
with tires of different diameters or with the
air pressure excessively low in any of its
tires.
T For vehicles without Vehicle Dy-
namics Control system
This light comes on when All-Wheel Drive
is disengaged and the drive mechanism is
switched to Front Wheel Drive for mainte-
nance or similar purposes.Continued driving with the AWD
warning light flashing can lead to
powertrain damage. If the AWD
warning light flashes, promptly park
in a safe place then check whether
all four tires are the same diameter
and whether any of the tires has a
puncture or has lost air pressure for
some other reason.
ProCarManuals.com

Page 137 of 355

3-24
Instruments and controls
TMist (for a single wipe)
For a single wipe of the wipers, pull the le-
ver toward you. The wipers operate until
you release the lever.
T Washer To wash the windshield, push the washer
button at the end of the wiper control le-
ver. The washer fluid sprays until you re-
lease the washer button. The wipers oper-
ate while you push the button.

Rear window wiper and wash-
er switch
: Washer (accompanied by wiper
operation)
ON : Normal
INT : Intermittent
OFF : Park
:Washer
TRear wiper
To turn the rear wiper on, turn the knob on
the end of the wiper control lever upward. INT: Intermittent
ON: Normal
To turn the wiper off, return the knob on
the end of the lever to the “OFF” position.
T
Washer
To wash the rear window while the rear
wiper is operating, turn the knob on the
end of the wiper control lever counter-
clockwise to the “ ” position. The
washer fluid sprays until you release the
knob.
To wash the rear window when the rear
wiper is not in use, turn the knob on the
end of the wiper control lever clockwise to
the “ ” position. The washer fluid
sprays and the wiper operates until you
release the knob.
300139300140
REAR
ONOFFINTINT
ON
INTOFF
300141
ProCarManuals.com

Page 139 of 355

3-26
Instruments and controls
The rear window defogger operates only
when the ignition switch is in the “ON” po-
sition.
The rear window defogger button is locat-
ed on the climate control panel.
To turn on the defogger, push the button.
To turn it off, push the button again.
The indicator light located on the button
lights up while the rear window defogger is
operating.
The defogger will automatically shut off af-
ter approximately 15 minutes. If the win-
dow clears before that time, push the but-
ton to turn it off. It also turns off when the
ignition switch is turned to the “ACC” or
“LOCK” position. If defrosting or defogging
is desired when you restart your vehicle,
you have to push the button to turn it on
again.
Turn on the rear window defogger if the
wiper is frozen to the glass.
MirrorsAlways check that the inside and outside
mirrors are properly adjusted before you
start driving.„Inside mirrorThe inside mirror has a day and night po-
sition. Pull the tab at the bottom of the mir-
ror toward you for the night position. Push
it away for the day position. The night po-
sition reduces glare from headlights.
y
Do not use sharp instruments or
window cleaner containing abra-
sives to clean the inner surface of
the rear window. They may dam-
age the conductors printed on the
window.
yTo prevent the battery from being
discharged, do not operate the de-
fogger continuously for any long-
er than necessary.
300145
ProCarManuals.com

Page 148 of 355

Climate control
4-5
– CONTINUED –
„Heater operationT Defrosting or defogging the wind-
shield
To direct warm air to the windshield and
front door windows:
1. Set the air flow control dial to the
“ ” position.
2. Turn the temperature control dial all the way to the right.
3. Set the fan speed control dial to the
highest speed.
If your vehicle is equipped with an air con-
ditioner, when the “ ” or “ ” posi-
tion is selected, the air conditioner com-
pressor automatically operates regardless
of the position of the air conditioner button
to defog the windshield quickly.
However, the air conditioner indicator light
does not come on at this time.
NOTEWarm air also comes out from the right
and left air outlets. To stop warm air
flow from these outlets, turn the corre-
sponding thumb-wheel down.
T
Heating and defrosting To direct warm air toward the floor and the
windshield:
1. Set the air flow control dial to the “ ”
position.
2. Set the temperature control dial to the
most comfortable level.
3. Set the fan speed control dial to the de-
sired speed.
If your vehicle is equipped with an air con-
ditioner, when the “ ” or “ ” posi-
tion is selected, the air conditioner com-
pressor automatically operates regardless
of the position of the air conditioner button
to defog the windshield quickly.
However, the air conditioner indicator light
does not come on at this time.
NOTEWarm air also comes out from the right
and left air outlets. To stop warm air
flow from these outlets, turn the corre-
sponding thumb-wheel down.
Continued operation with the air in-
let selection button in the ON posi-
tion may fog up the windows.
Switch to the OFF position as soon
as the outside dusty condition
clears.
400146
400147
ProCarManuals.com

Page 149 of 355

4-6
Climate control
THeating
To direct warm air toward the floor:
1. Set the air inlet selection button to the
OFF position.
2. Set the air flow control dial to the
“ ” position.
3. Set the temperature control dial to the
most comfortable level.
4. Set the fan speed control dial to the de-
sired speed.NOTEWarm air also comes out from the right
and left air outlets. To stop warm air
flow from these outlets, turn the corre-
sponding thumb-wheel down. T
Bi-level heating
This setting allows you to direct air of dif-
ferent temperatures from the instrument
panel and foot outlets. The air from the
foot outlets is slightly warmer than from
the instrument panel outlets.
1. Set the air inlet selection button to the
OFF position.
2. Set the air flow control dial to the
“ ” position.
3. Set the temperature control dial to the
desired temperature level.
4. Set the fan speed control dial to the de-
sired speed.
Setting the temperature control dial fully
turned to the red area or blue area de-
creases the temperature difference be-
tween the air from the instrument panel outlets and the air from the foot outlets.
T
Ventilation
To force outside air through the instru-
ment panel outlets:
1. Set the air inlet selection button to the
OFF position.
2. Set the air flow control dial to the “ ”
position.
3. Set the temperature control dial all the
way left.
4. Set the fan speed control dial to the de-
sired speed.
When driving on a dusty road, set the air
inlet selection button to the “ON” position.
400148
400149
400150
ProCarManuals.com

Page 180 of 355

6
Interior equipment
Interior lights ...................................................... 6-2
Dome light ............................................................... 6-2
Cargo area light ..................................................... 6-2
Map lights ........................................................... 6-3
Sun visors ........................................................... 6-3
Vanity mirror ........................................................... 6-3
Storage compartments ...................................... 6-4
Glove box ................................................................ 6-4
Center console ........................................................ 6-4
Overhead console .................................................. 6-6
Dashboard storage compartment ......................... 6-6
Convenience net ..................................................... 6-6
Cup holders ........................................................ 6-7
Front passenger’s cup holder ............................... 6-7
Rear passenger’s cup holder ................................ 6-7
Accessory power outlets ................................... 6-8
Cigarette lighter socket ..................................... 6-9
Use with a cigarette lighter (if equipped) ............. 6-10
Using as an accessory power outlet ..................... 6-10
Ashtray ................................................................\
6-11
Floor mat ............................................................. 6-11
Coat hook ............................................................ 6-12
Cargo area cover (if equipped) ......................... 6-12
Using the cover ....................................................... 6-12
To remove the cover .............................................. 6-13
Stowage of the cover ............................................. 6-13
To install the cover housing .................................. 6-13
Shopping bag hook ............................................ 6-13
Cargo tie-down hooks ........................................ 6-14
Cargo area bars .................................................. 6-14
Under-floor storage compartment .................... 6-14
ProCarManuals.com

Page 184 of 355

Interior equipment
6-5
– CONTINUED –
To use as rear passenger’s cup holder:
With the console top tipped toward the
rear seat, it can be used as a cup holder.
To use as storage space:
Raise the console top to the vertical posi-
tion or tip it toward the rear seat. Then, pull
up the lock button of the console box and
open the lid.
When closed, the lid can be used as a tray
for placing small items in it.
Do not step or sit on the armrest,
and do not place heavy objects on it.
The armrest could break, and you
could get hurt.
600520
yTo switch from using the console
top as an armrest to using it as a
rear passenger’s cup holder, raise
the console top to the vertical po-
sition before tipping it toward the
rear seat. Otherwise the console
top may break.
y Do not place any object weighing
more than 4.4 lbs (2 kg) on the ta-
ble.
y Do not have hot drinks or other
objects on the table while driving.
During hard braking or negotia-
tion of a curve, they could fall
from the table and cause a burn or
other injury.
yBefore opening the lid of the con-
sole box, raise the console top
completely to the vertical position
or tip it toward the rear seat. Oth-
erwise, the lid may be damaged
and an injury may occur.
600475
ProCarManuals.com

Page 192 of 355

Interior equipment
6-13
„To remove the cover1. Rewind the cover.
2. Take it off the retainer, lift it out.
3. Store the cover housing in the cargo
area.
„Stowage of the coverOn models having a temporary spare tire,
the cargo area cover can be stowed in un-
der the cargo floor.„To install the cover housingTo install the cover, insert both ends of the
cover housing into the retainers.
Shopping bag hookIn the cargo area, there are two retract-
able shopping bag hooks (one on each
side) and four non-retractable shopping
bag hooks (two on each side).
To use either of the retractable hooks, pull
the lower portion out.
Do not place anything on the ex-
tended cover. Putting excessive
weight on the extended cover can
break it and an object on the cover
could tumble forward in the event of
a sudden stop or collision. This
could cause serious injury.
600100
600101
Do not hang items on the shopping
bag hook that weigh 6.6 lbs (3 kg) or
more.
600492
ProCarManuals.com

Page 213 of 355

7-18
Starting and operating
Electronic Brake Force Dis-
tribution (EBD) system (if equipped)The EBD system maximizes the effective-
ness of the brakes by allowing the rear
brakes to supply a greater proportion of
the braking force. It functions by adjusting
the distribution of braking force to the rear
wheels in accordance with the vehicle’s
loading condition and speed.
The EBD system is an integral part of the
ABS system and uses some of the ABS
system’s components to perform its func-
tion of optimizing the distribution of brak-
ing force. If any of the ABS components
used by the EBD function fails, the EBD
system also stops working.
When the EBD system is operating, you
may hear a chattering noise or feel a slight
vibration in the brake pedal. This is normal
and does not indicate a malfunction.
„Steps to take if EBD system
fails1) U.S.-spec. models
2) Canada-spec. modelsIf a malfunction occurs in the EBD system,
the system stops working and the brake
system warning light and ABS warning
light come on simultaneously.
The EBD system may be faulty if the brake
system warning light and ABS warning
light illuminate simultaneously during driv-
ing.
Even if the EBD system fails, the conven-
tional braking system will still function.
However, the rear wheels will be more
prone to locking when the brakes are ap-
plied harder than usual and the vehicle’s motion may therefore become somewhat
harder to control.
If the brake system warning light and ABS
warning light illuminate simultaneously,
take the following steps:
1. Stop the vehicle in the nearest safe, flat
place.
2. Shut down the engine, then restart it.
3. Release the parking brake. If both
warning lights go out, the EBD system
may be faulty.
Drive carefully to the nearest SUBARU
dealer and have the system inspected.
4. If both warning lights come on again
and stay illuminated after the engine has
been restarted, shut down the engine
again, apply the parking brake, and check
the brake fluid level.
5. If the brake fluid level is not below the
“MIN” mark, the EBD system may be
faulty. Drive carefully to the nearest
SUBARU dealer and have the system in-
spected.
6. If the brake fluid level is below the
“MIN” mark, DO NOT drive the vehicle. In-
stead, have the vehicle towed to the near-
est SUBARU dealer for repair.
1
2 1
2
700334
ProCarManuals.com

Page:   < prev 1-10 11-20 21-30 31-40 41-50 51-60 ... 60 next >