bulb SUBARU FORESTER 2006 Owners Manual

10

Illustrated index„Exterior
6
78910
11
1
2
3 4
5
000194
1) Headlight switch (page 3-18)
2) Replacing bulbs (page 11-43)
3) Engine hood (page 11-4)
4) Wiper switch (page 3-23)
5) Roof rails (page 8-13)
6) Door locks (page 2-4)
7) Tire pressure (page 11-30)
8) Flat tires (page 9-3)
9) Tire chains (page 8-10)
10) Front fog light button (page 3-21)
11) Tie-down/Towing hooks (page 9-11)
ProCarManuals.com

Instruments and controls
3-9
– CONTINUED –
AT vehicles
1) U.S.-spec. models
2) Canada-spec. modelsThe outside temperature indicator is locat-
ed below the odometer/trip meter. The in-
dicator can indicate an outside tempera-
ture ranging from –22 to 122 °F (–30 to
50° C).
The indicator can give a false reading un-
der any of the following conditions:
y When there is too much sun.
y During idling; while running at low
speeds in a traffic jam; when the engine is
restarted immediately following a shut-
down.
y When the actual outside temperature
falls outside the specified indicator range.
Warning and indicator lightsSeveral of the warning and indicator lights
come on momentarily and then go out
when the ignition switch is initially turned
to the “ON” position. This permits check-
ing the operation of the bulbs.
Apply the parking brake and turn the igni-
tion switch to the “ON” position. The fol-
lowing lights come on:
Seatbelt warning light
SRS airbag system warning light
Front passenger’s frontal airbag ON in-
dicator light
Front passenger’s frontal airbag OFF
indicator light
CHECK ENGINE warning light/Mal-
function indicator lamp
Charge warning light
Oil pressure warning light
AT OIL temperature warning light (AT
vehicles)
ABS warning light
Vehicle Dynamics Control warning light
(if equipped)/Vehicle Dynamics Control
OFF indicator light (if equipped)
Brake system warning light
All-Wheel Drive warning light (AT vehi-
cles)
Vehicle Dynamics Control operation in-
dicator light (if equipped) Cruise control indicator light (if
equipped)
Cruise control set indicator light (if
equipped)
If any lights fail to come on, it indicates a
burned-out bulb or a malfunction of the
corresponding system.
Consult your authorized SUBARU dealer
for repair.
„ Seatbelt warning light
and chimeYour vehicle is equipped with a seatbelt
warning device at the driver’s seat, as re-
quired by current safety standards. There
is a seatbelt warning light in the combina-
tion meter.
If the driver has not yet fastened the seat-
belt when the ignition switch is turned to
the “ON” position, the seatbelt warning
light will flash for 6 seconds, to warn that
the seatbelt is unfastened. If the driver’s
seatbelt is not fastened, a chime will also
sound simultaneously.
If the driver’s seatbelt is still not fastened
6 seconds later, the warning light will re-
main lit for 15 seconds. If the driver’s seat-
belt is still not fastened even 15 seconds
later (21 seconds after turning ON the ig-
nition switch), the warning lights will alter-
nate between flashing and steady illumi-
12
300576
ProCarManuals.com

3-16
Instruments and controls
This light flashes if the vehicle is driven
with tires of different diameters or with the
air pressure excessively low in any of its
tires.„Vehicle Dynamics Con-
trol operation indicator
light (if equipped)This light comes on when the ignition
switch is ON and goes out approximately
2 seconds later.
It blinks when the skid suppression func-
tion is activated. It illuminates when only
the traction control function is operating.
The Vehicle Dynamics Control system is
probably faulty under any of the following
conditions. Have your vehicle checked at
a SUBARU dealer immediately.
yThe light does not come on when the ig-
nition switch is turned to the “ON” position.
y The light does not go out even after a
period of approximately 2 seconds after
the ignition switch has been turned to the
“ON” position.
„ Shift position indicator (AT
vehicles)This indicator shows the position of the
shift lever.„Turn signal indicator
lightsThese lights show the operation of the
turn signal or lane change signal.
If the indicator lights do not blink or blink
rapidly, the turn signal bulb may be
burned out. Replace the bulb as soon as
possible. Refer to the “Replacing bulbs”
section in chapter 11.
„High beam indicator
lightThis light shows that the headlights are in
the high beam mode.
This indicator light also comes on when
the headlight flasher is operated.„Cruise control indica-
tor lightThe cruise control indicator light comes on
when the ignition switch is turned to the
“ON” position and goes out after approxi-
mately three seconds.
This light comes on when the “CRUISE”
main switch is pressed.NOTEyIf you move the cruise control lever
or press the main switch button while
turning the ignition switch “ON”, the
cruise control function is deactivated
and the “CRUISE” indicator light flash-
es. To reactivate the cruise control
function, turn the ignition switch back
to the “ACC” or “LOCK” position, and
then turn it again to the “ON” position.
y If this indicator light and the “ ”
indicator light flash simultaneously
during driving, have the vehicle
checked by your nearest SUBARU
dealer.
300124
ProCarManuals.com

Maintenance and serviceReplacement of brake pad and lining ............... 11-28
Breaking-in of new brake pads and linings ......... 11-28
Parking brake stroke .......................................... 11-29
Tires and wheels ................................................ 11-29
Types of tires .......................................................... 11-29
Tire inspection ........................................................ 11-30
Tire pressures and wear ........................................ 11-30
Wheel balance ........................................................ 11-32
Wear indicators ....................................................... 11-32
Tire rotation ............................................................. 11-32
Tire replacement ..................................................... 11-33
Wheel replacement ................................................. 11-33
Aluminum wheels (if equipped) ........................ 11-34
Windshield washer fluid .................................... 11-34
Replacement of wiper blades ............................ 11-36
Windshield wiper blades ........................................ 11-36
Rear window wiper blade ....................................... 11-37
Battery ................................................................\
. 11-39
Fuses ..................................................................\
. 11-40
Main fuse ............................................................. 11-41
Installation of accessories ................................ 11-42
Replacing bulbs .................................................. 11-43
Headlights (Canada-spec. 2.5XT) .......................... 11-44
Headlights (Except Canada-spec. 2.5XT) ............. 11-45
Rear combination lights ......................................... 11-46
License plate light .................................................. 11-47
Dome light and map light ....................................... 11-47
High mount stop light ............................................ 11-48
ProCarManuals.com

Maintenance and service
11 - 4 3
– CONTINUED –
Replacing bulbs
321
11
12
13
15 14
7
86 54
910
B00384
ProCarManuals.com

11 - 4 4
Maintenance and service
WattageBulb No.
1) High beam headlight 12V-60W9005 (HB3)
2) Low beam headlight Canada-spec. 2.5XT 12V-35W D2R
All except Canada-spec.
2.5XT 12V-55W
H1
3) Front turn signal light 12V-21W (Amber) 1474
4) Map light 12V-8W–
5) Dome light 12V-8W–
6) Side marker light (Front) 12V-5W 168
7) Front fog light 12V-55W9006 (HB4)
8) Parking light 12V-5W168
9) High mount stop light 12V-13W912
10) Cargo area light 12V-5W–
11) Tail/stop light 12V-21/5W7443
12) Backup light 12V-16W921
13) Rear turn signal light 12V-21W (Amber) 1474
14) Tail/stop light 12V-21/5W7443
15) License plate light 12V-5W168
„Headlights (Canada-spec.
2.5XT)Replace any bulb only with a new
bulb of the specified wattage. Using
a bulb of different wattage could re-
sult in a fire.High-intensity-discharge (HID) bulbs
are used for the low beams of the
headlights on the Canada-spec.
2.5XT. These HID bulbs use an ex-
tremely high voltage. To avoid the
risk of an electric shock and result-
ing serious injury, you should not at-
tempt to replace them. Neither
should you attempt to replace the
high-beam bulbs, remove/refit the
headlight assemblies, or remove any
headlight-assembly components.
For replacement of the headlight
bulbs (low-beam and high-beam), re-
moval and installation of the head-
light assemblies, and removal of
headlight-assembly components,
contact your SUBARU dealer.
ProCarManuals.com

Maintenance and service
11 - 4 5
– CONTINUED –
„Headlights (Except Canada-
spec. 2.5XT)Before replacing the left-hand (battery-
side) low- or high-beam light bulb, remove
the screw that retains the windshield
washer nozzle and tip the windshield
washer nozzle sideways.
NOTEyIf headlight aiming is required, con-
sult your SUBARU dealer for proper
adjustment of the headlight aim.
y It may be difficult to replace the
bulbs. Have your SUBARU dealer re-
place the bulbs if necessary. T
Low beam light bulbs
1. Remove the bulb cover, by turning it
counterclockwise.
2. Remove the retainer spring, then pull
out the bulb and electrical connector unit.
B00393
Halogen headlight bulbs become
very hot while in use. If you touch
the bulb surface with bare hands or
greasy gloves, finger prints or
grease on the bulb surface will de-
velop into hot spots and cause the
bulb to break. If there are finger
prints or grease on the bulb surface,
wipe them away with a soft cloth
moistened with alcohol.
B00385B00386
ProCarManuals.com

11 - 4 6
Maintenance and service
3. Disconnect the electrical connector
from the bulb.
4. Install a new bulb into the electrical
connector, then set the retainer spring se-
curely.
5. Install the bulb cover.T
High beam light bulbs
1. Disconnect the electrical connector
from the bulb.
2. Remove the bulb from the headlight
assembly by turning it counterclockwise. 3. Replace the bulb with new one.
4. Reconnect the electrical connector. At
this time, use care not to touch the bulb
surface.
5. To install the bulb to the headlight as-
sembly, turn it clockwise until it clicks.
„
Rear combination lights1. Remove the upper and lower screws.
Then, slide the rear combination lamp as-
sembly to the rear and remove it from the
vehicle.
B00387
700093B00388
B00389
ProCarManuals.com

Maintenance and service
11 - 4 7
– CONTINUED –
1) Tail/stop light
2) Backup light
3) Rear turn signal light
4) Tail/stop light2. Remove the bulb holder from the rear
combination light assembly by turning it
counterclockwise.
3. Pull the bulb from the holder. Install a
new bulb.
4. Set the bulb holder into the rear combi-
nation light assembly and turn it clockwise
until it locks.
5. Reinstall the rear combination light as-
sembly.
„License plate light
0
1. Remove the mounting screws using a
Phillips screwdriver.
2. Remove the cover and lens.
3. Pull the bulb out of the socket. Install a
new bulb.
4. Reinstall the lens and cover.
5. Tighten the mounting screws.
„Dome light and map lightDome light
Map light1. Remove the lens by prying the edge of
1234
B00390
B00391
B00090B00091
ProCarManuals.com

11 - 4 8
Maintenance and service
the lens with a flat-head screwdriver.
2. Pull the bulb out of the socket. Install a
new bulb.
3. Reinstall the lens.„High mount stop light
0
1. Remove the mounting screw covers by
prying the edge with a flat-head screwdriv-
er.
2. Remove the mounting screws using a
Phillips screwdriver and then remove the
high mount stop light cover.
3. Pull the bulb from the socket. Install a
new bulb.
4. Reinstall the cover.
5. Tighten the mounting screws then rein-
stall the covers.
NOTEOther bulbs may be difficult to replace.
Have your SUBARU dealer replace
these bulbs if necessary.
B00093
ProCarManuals.com