SUBARU IMPREZA 2001 2.G Owners Manual

Maintenance and service10-43
–
CONTINUED –
Fuses
HG0127
HS0202
The fuses are d esig ned to melt d uring an overload t o p revent d amag e to
the wiring harness and elec tric al eq uip ment. The fu ses are loc ated in
two fuse b oxes.
If any lig hts, ac c essories or other elec tric al c ont rols d o not op erate, in-
sp ec t the c orresp ond ing fuse. If a fuse has b lown, rep lac e it.
HS0204
Good Blown
CAUTION
Never replace a fuse with one having a higher rating or with mate-
rial other than a fuse because serious damage or a fire could re-sult.

10-44
Fuse box (behind the coin tray)
1. Turn the ig nition switc h to the “LOCK ” p osition and turn off all elec -
tric al ac c essories.
HS0202
2. Op en the c oin tray and p ull it horizontally to re move it.
3. Determine whic h fuse may b e b lown. The b ac k sid e of the c oin
tray and the “Fuse and c irc uits ” sec tion in c hap ter 11 in this manual
show the c irc uit for eac h fuse.
HS0208
HS0207
Fuse puller Fuse puller
Spare fuses
4. Pull out the fuse with the fuse p uller. The fuse p uller is stored in the
main fuse b ox c over in the eng ine c omp artment.
5. Insp ec t the fuse. If it has b lown, rep lac e it wit h a sp are fuse of the
same rating . The sp are fuses are stored in the main fuse b ox c over in
the eng ine c omp artment.
6. If the same fuse b lows ag ain, this ind ic ates that its system has a

Maintenance and service10-45
–
CONTINUED –
p rob lem. Contac t your SUBARU d ealer for rep airs.
Main fuse box (in the engine compartment)
1. Turn the ig nition switc h to the “LOCK ” p osition and turn off all elec -
tric al ac c essories.
2. Op en the eng ine hood .
3. Remove the main fuse b ox c over.
4. Determine whic h fuse may b e b lown. The fuse b ox c over and
“ Fuse and c irc uits ” sec tion in c hap ter 11 in this manual show the c ir-
c uit for eac h fuse.
HS0208
HS0207
Fuse puller Fuse puller
Spare fuses
5. Pull out the fuse with the fuse p uller p rovid ed i n the main fuse b ox
c over.
6. Insp ec t the fuse. If it has b lown, rep lac e it wit h a sp are fuse of the
same rating . The sp are fuses are stored in the main fuse b ox c over in
the eng ine c omp artment.
7. If the same fuse b lows ag ain, this ind ic ates that its system has a
p rob lem. Contac t your SUBARU d ealer for rep airs.

10-46Main fuse and fusible link
HG0127
The main fuses and fusib le link are d esig ned to mel
t d uring an overload
to p revent d amag e to the wiring harness and elec tri c al eq uip ment.
Chec k the main fuses and fusib le link if any elec tr ic al c omp onent fails to
op erate (exc ep t the starter motor) and other fuses are g ood . A melted
main fuse or fusib le link must b e rep lac ed . Use onl y rep lac ements with
the same sp ec ified rating as the melted main fuse o r fusib le link. If a
main fuse or fusib le link b lows after it is rep lac e d , have the elec tric al sys-
tem c hec ked b y your nearest SUBARU d ealer.
Installation of accessories
Always c onsult your SUBARU d ealer b efore installing fog lig hts or any
other elec tric al eq uip ment in your vehic le. Suc h ac c essories may c ause
the elec tronic system to malfunc tion if they are in c orrec tly installed or if
they are not suited for the vehic le.

Maintenance and service10-47
–
CONTINUED –
Replacing bulbs
Headlight
CAUTION
Halogen headlight bulbs become very hot while in use. If you touch the bulb surface with bare hands or greasy gloves, fingerprints or grease on the bulb surface develop into hot spots, caus-ing the bulb to break. If there are finger prints or grease on thebulb surface, wipe them away with a soft cloth moistened with al-cohol.
OM-H0261
OM-H0243
Retainer spring
Rubber cover
Electrical connector
1. Disc onnec t the elec tric al c onnec tor, then remove the rub b er c over.
2. Remove the retainer sp ring .
3. Rep lac e the b ulb , then set the retainer sp ring se c urely.
4. Install the rub b er c over with the top mark fac ing up , then rec onnec t
the elec tric al c onnec tor.

10-48
Fog light (if equipped)
CAUTION
Halogen light bulbs become very hot while in use. If you touch the bulb surface with bare hands or greasy gloves, finger prints
or grease on the bulb surface develop into hot spots, causing thebulb to break. If there are finger prints or grease on the bulb sur-face, wipe them away with a soft cloth moistened with alcohol.
Type A
HGA002BA
HGA001BB
1. Remove the front fog lig ht assemb ly b y removing t
he three b olts.
2. Disc onnec t the c onnec tor.
3. Remove the front fog lig ht c ase c ap b y turning it c ounterc loc kwise.
OM-H0412
Connector
Spring

Maintenance and service10-49
–
CONTINUED –
4. Disc onnec t the c onnec tor b ehind the c ase c ap .
5. Release the retainer sp ring .
6. Rep lac e the b ulb with a new one. Then rec onnec t t
he c onnec tors
and reinstall the removed p arts in the reverse ord e r of removal.
Type B
HG0326
HG0325
1. Remove the front fog lig ht c over.
2. Remove the front fog lig ht assemb ly b y removing t he two b olts.
3. Disc onnec t the c onnec tor.
4. Remove the front fog lig ht c ase c ap b y turning it c ounterc loc kwise.
HG0327
Spring
Connector
5. Disc onnec t the c onnec tor b ehind the c ase c ap .
6. Release the retainer sp ring .
7. Rep lac e the b ulb with a new one. Then rec onnec t t he c onnec tors
and reinstall the removed p arts in the reverse ord e r of removal.

10-50
Parking light
OM-H0244
1. Remove the p arking lig ht assemb ly mounting sc rew loc ated at the top
of the head lig ht assemb ly using the p hillip s sc rewd river.
2. Move the p arking lig ht assemb ly forward until it p op s out from the
fend er.
3. Remove the b ulb hold er from the p arking lig ht ass emb ly b y turning it
c ounterc loc kwise.
4. Pull the b ulb out of the soc ket. Install a new b u lb .
5. Set the b ulb hold er into the p arking lig ht assemb ly and turn it c loc k-
wise until it loc ks.
6. Set the p arking lig ht assemb ly into the fend er. T ig hten the mounting
sc rew.

Maintenance and service10-51
–
CONTINUED –

Front turn signal light Type A
HGA011BB
1. Remove the b olt sec uring the front turn sig nal li g ht assemb ly.
2. Remove the front turn sig nal lig ht assemb ly from the front b ump er
and remove the b ulb soc ket b y turning it c ounterc lo c kwise.
3. Remove the b ulb from the soc ket b y p ushing it in and turning
c loc kwise, then install a new b ulb .
4. Install the removed p arts in the reverse ord er of removal.
Type B
HG0194
1. Remove the front turn sig nal lig ht assemb ly mount ing sc rews using
the p hillip s sc rewd river.
2. Remove the lens from the front turn sig nal lig ht assemb ly.

10-523. Remove the b ulb from the soc ket b y p ushing it in
and turning
c ounterc loc kwise. Install a new b ulb .
4. Reinstall the lens to the front turn sig nal lig ht assemb ly and tig hten
the mounting sc rews.
Side turn signal light
OM-H0246
1. Pull the left sid e of the turn sig nal lig ht assem b ly while moving it for-
ward in relation to the vehic le.
2. Remove the b ulb hold er from the sid e turn sig nal lig ht assemb ly b y
turning it c ounterc loc kwise.
3. Pull the b ulb out of the soc ket. Install a new b u lb .
4. Set the b ulb hold er into the sid e turn sig nal lig ht assemb ly and turn it
c loc kwise until it loc ks.
5. Reinstall the sid e turn sig nal lig ht assemb ly on the sid e of the front
fend er.