display SUBARU IMPREZA 2016 5.G Multimedia System Manual

PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
132
NOTE
OThe pop up screen is separately available for incoming e-mail
and SMS/MMS messages under the following conditions:
‡ “Incoming E-mail Display (Incoming E-mail Display)” is set to

PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
133
PHONE
4
NOTE
OThe text of the message is not displayed while driving.
O Turn the “POWER/VOLUME” knob, or use the volume control
switch on the steering wheel to adjust the message readout
volume.
REPLYING TO A MESSAGE (QUICK REPLY)
15 messages have already been stored.
1.'LVSOD\WKHPHVVDJHLQER[VFUHHQ
:3
2.Select the desired message from the list.
3.SelectQuick Message (Quick Message).
4.Select the desired message.
5.SelectSend (Send).

” While the message is being sent, a sending message
screen is displayed.
EDITING QUICK REPLY MESSAGES
This operation cannot be performed while driving.
1.SelectQuick Message (Quick Message).
2.Select corresponding to the desired message to
edit.
3.SelectOK (OK) when editing is completed.
NOTE
O
To reset the editquick reply messages, select Default(Default).

PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
134
NOTE
O“Quick Message 1” (I'm driving right now. I will call you back later.
(I'm driving right now. I will call you back later.)*1 or
I am driving and will arrive in approximately [ETA] minutes. (I am
driving and will arrive in approximately [ETA] minutes.)*2)
cannot be edited. [ETA] will automatically be replaced with the
HVWLPDWHGWLPHRIDUULYDORQWKHFRQ¿UPPHVVDJHVFUHHQ
If there are waypoints set, [ETA] to the next waypoint will be
shown.
If there is no route currently set in the navigation system, “Quick
Message 1” cannot be selected.
*1: Without navigation function
*2: With navigation function
CALLING THE MESSAGE SENDER
Calls can be made to an e-mail/SMS/MMS message
sender’s phone number.
This operation can be performed while driving.
CALLING FROM E-MAIL/SMS/MMS MESSAGE
DISPLAY
1.'LVSOD\WKHPHVVDJHLQER[VFUHHQ
:3
2.Select the desired message.
3.Select.

” If there are 2 or more phone numbers, select the
desired number.
4.Check that the “Call (Call)” screen is displayed.
CALLING FROM A NUMBER WITHIN A MESSAGE
&DOOV FDQ EH PDGH WR D QXPEHU LGHQWL

SETUP
136
SETUP
PHONE/MESSAGE SETTINGS
1.Select.
2.SelectSETTINGS (SETTINGS).
3.SelectPhone (Phone).
4.Select the item to be set.
PHONE/MESSAGE SETTINGS SCREEN
No.
Information Page
Connect phone 181
Sound settings137
Contact/call history settings138
Messaging settings 145
Phone display settings146

SETUP
137
PHONE
4
DISPLAYING THE PHONE/MESSAGE SETTINGS
SCREEN IN A DIFFERENT WAY
1.'LVSOD\WKHSKRQHWRSVFUHHQ
:3
2.Select.
“Sound Settings (Sound Settings)” SCREEN
The call and ringtone volume can be adjusted. A ringtone
can be selected.
1.Display the “Phone/Message Settings (Phone/Message
6HWWLQJV

SETUP
138
No.Function
Select to set the desired incoming e-mail tone.
Select or to adjust the incoming e-mail tone
volume.
Select or to adjust the default volume of the
other party’s voice.
Select to reset all setup items.
“Contact/Call History Settings (Contact/Call
History Settings)” SCREEN
The contact can be transferred from a Bluetooth phone
to the system. The contact also can be added, edited and
deleted.
The call history can be deleted and contact and speed dial
can be changed.
1.Display the “Phone/Message Settings (Phone/Message
6HWWLQJV

SETUP
139
PHONE
4
No.Function Page
Select to add contacts to the speed dial list. 143
Select to delete contacts from the speed dial
list. 144
Select to set the transferred contact image
display on/off. -
*
Select to clear contacts from the call history. -
*Select to add new contacts to the contact list. 140
*Select to edit contacts in the contact list. 141
*Select to delete contacts from the contact list. 142
Select to reset all setup items. -
*: For PBAP compatible Bluetooth phones, this function is available when
“Automatic Contact/History Transfer (Automatic Contact/History Transfer)”
LVVHWWRRII
:3
NOTE
OContact data is managed independently for every registered
phone. When one phone is connected, another phone’s
registered data cannot be read.
UPDATE CONTACTS FROM PHONE
Operation methods differ between PBAP compatible and
OPP compatible Bluetooth phones.
If your cellular phone is neither PBAP nor OPP compatible,
the contacts cannot be transferred.
Q FOR PBAP COMPATIBLE Bluetooth PHONES
1.SelectUpdate Contacts from Phone (Update
Contacts from Phone).

” Contacts are transferred automatically.
2.&KHFN WKDW D FRQ

SETUP
142
3.SelectEdit Contact (Edit Contact).

”E-mail Addresses (E-mail Addresses): Select to
display all registered e-mail addresses for the contact.
4.Follow the steps in “EDITING THE CONTACT DATA”
IURP

SETUP
147
PHONE
4
3.Select the desired item to be set.
No.Function
Select to change the incoming call display.
Full Screen (Full Screen): When a call is received,
the hands-free screen is displayed and can be operated
on the screen.
Drop-Down (Drop-Down): A message is displayed
on the upper side of the screen.
Select to set display of the contact/history transfer
completion message on/off.
Select to reset all setup items.

BEFORE USING THE APPLICATION
150
BEFORE USING THE APPLICATION
BEFORE USING THE APPLICATION
Precautions to be aware of when using the application are
shown below.
In this chapter, iPhone or Android devices will be referred to
as a smartphone.
WARNING
ODo not connect or operate the smartphone while driving.
O Be sure to park the vehicle in a safe location before
connecting or operating the smartphone.
CAUTION
ODo not leave your smartphone in the car. In particular, high
temperatures inside the vehicle may damage the smartphone.
O Do not push down on or apply unnecessary pressure to the
smartphone while it is connected as this may damage the
smartphone or its terminal.
O If connecting your smartphone via USB, do not insert foreign
objects into the USB port as this may damage the smartphone
or its terminal.
NOTE
O Depending on the application, certain functions are not available
while driving for reasons of safety.
O In order to maximize signal reception, performance and precision
of the smartphone, please ensure the smartphone is placed as
close to the system as possible, while ensuring it is stowed and
secure while driving.
O When connecting your smartphone via USB, use the original
cables provided with your smartphone or equivalent third-party
FHUWL¿HGFDEOHV
O When the ignition switch is in the “ACC” or “ON” position, t\
he
battery of the connected smartphone is charged.
O If connecting your smartphone via USB, smartphone may not
be recognized when the ignition switch is in the “ACC” or “ON”\

position. In this case, remove the smartphone and reconnect it.
O The accuracy of the displayed information or the signal reception
performance depends on the smartphone or the connected
device, and its wireless connection.
O For operating the smartphone, see the instruction manual that
comes with it.
O )ROORZ WKH VSHFL