washer fluid SUBARU IMPREZA WRX 2003 2.G Owners Manual

Instruments and controls
3-21
– CONTINUED –
Wiper and washer
WARNING
In freezing weather, do not use the windshield
washer until the windshield is sufficiently
warmed by the defroster.Otherwise the washer fluid can freeze on the
windshield, blocking your view.
CAUTION
Do not operate the washer continuously for
more than ten seconds, or when the washer
fluid tank is empty. This may cause overheat-
ing of the washer motor. Check the washer
fluid level frequently, such as at fuel stops. Do not operate the wipers when the wind-
shield or rear window is dry. This may scratchthe glass, damage the wiper blades and causethe wiper motor to burn out. Before operating
the wiper on a dry windshield or rear window,
always use the windshield washer. In freezing weather, be sure that the wiper
blades are not frozen to the windshield or rear window before switching on the wipers.Attempting to operate the wiper with the
blades frozen to the window glass could
cause not only the wiper blades to be dam-aged but also the wiper motor to burn out. Ifthe wiper blade is frozen to the window glass,
be sure to operate the defroster, windshield wiper deicer (if equipped) or rear window
defogger before turning on the wiper.
If the wipers stop during operation because
of ice or some other obstruction on the win-
dow, the wiper motor could burn out even if the wiper switch is turned off. If this occurs, promptly stop the vehicle in a safe place, turnthe ignition switch to the “LOCK” position and
clean the window glass to allow proper wiperoperation. Use clean water if windshield washer fluid is
unavailable. In areas where water freezes in
winter, use SUBARU Windshield Washer Fluidor the equivalent. (See the “Windshield wash-
er fluid ” section in chapter 11.)
Also, when driving the vehicle when there are
freezing temperatures, use non-freezing type wiper blades. Do not clean the wiper blades with gasoline
or a solvent, such as paint thinner or benzene.

Instruments and controls
3-24
Washer
To wash the windshield, push the washer button at
the end of the wiper control lever. The washer fluid
sprays until you release the washer button. The wip-ers operate while you push the button.
Rear window wiper and washer
switch – Wagon
1) Rear wiper 2) Washer
Rear wiper
The rear wiper offers intermittent operation only.
To turn the rear wiper on, turn the knob on the end of
the wiper control lever to the “ON” position.
To turn the wiper off, return the knob on the end of the lever to the “OFF” position.
Washer
To wash the rear window while the rear wiper is op-
erating, turn the knob on the end of the wiper control

Instruments and controls
3-25
– CONTINUED –
lever counterclockwise to the “” position. The
washer fluid sprays until you release the knob.
To wash the rear window when the rear wiper is not
in use, turn the knob on the end of the wiper controllever clockwise to the “
” position. The washer
fluid sprays and the wiper operates until you release the knob. Rear window defogger switch
The rear window defogger operates only when the
ignition switch is in the
“ON” position.
The rear window defogger switch is located on the
climate control panel.
The defogger will automatically shut off after about
15 minutes. If the window clears before that time,
push the switch to turn it off. It also turns off when
the ignition switch is turned to the “ACC” or “LOCK”
position. If defrosting or defogging is desired when
you restart your vehicle, you have to push the switch
to turn it on again.

Starting and operating
7-8
mination is observed, there is no stored diagnostic
trouble codes, and the OBD system readiness moni-
tors are complete. A vehicle fails
the OBD inspection if the “CHECK
ENGINE ” warning light/MIL is not properly operating
or there is one or more diagnostic trouble codes
stored in vehicle ’s computer with the “CHECK
ENGINE ” warning light/MIL illuminated.
A state emission inspection may reject (not pass
or fail) a vehicle if the number of OBD system readi- ness monitors “Not Ready ” is greater than three.
Under this condition, the vehicle operator should be instructed to drive his/her vehicle for a few days to
set the monitors and return for an emission re-in-spection. Owners of rejected or failing vehicles should con-
tact their Subaru Dealer for service. Preparing to drive
You should perform the following checks and adjust-
ments every day before you start driving.
1. Check that all windows, mirrors, and lights are
clean and unobstructed.
2. Check the appearance and condition of the tires.
Also check tires for proper inflation.
3. Look under the vehicle for any sign of leaks.
4. Check that the hood, trunk and rear gate are fullyclosed.
5. Check the adjustment of the seat.
6. Check the adjustment of the inside and outside
mirrors.
7. Fasten your seatbelt. Check that your passen-gers have fastened their seatbelts.
8. Check the operation of the warning and indicator
lights when the ignition switch is turned to the
“ON”
position.
9. Check the gauges, indicator and warning lights
after starting the engine. NOTE Engine oil, engine coolant, brake fluid, washer
fluid and other fluid levels should be checked
daily, weekly or at fuel stops.

Driving tips
8-11
– CONTINUED –
cold weather. Heavy summer oil will cause harder
starting.
Keep the door locks from freezing by squirting themwith deicer or glycerin.
Forcing a frozen door open may damage or sepa-
rate the rubber weather strips around the door. If the
door is frozen, use hot water to melt the ice, and af-
terwards thoroughly wipe the water away. Use a windshield washer fluid that contains an anti-
freeze solution. Do not use engine antifreeze or oth-
er substitutes because they may damage the paint of the vehicle.
Before driving your vehicle
Before entering the vehicle, remove any snow or ice
from your shoes because that could make the ped-
als slippery and dangerous.
While warming up the vehicle before driving, check that the accelerator pedal, brake pedal, and all oth-
er controls operate smoothly. Clear away ice and snow that has accumulated un-
der the fenders to avoid making steering difficult.
During severe winter driving, stop when and where it is safe to do so and check under the fenders peri-
odically.
Parking in cold weather
Do not use the parking brake when parking for long
periods in cold weather since it could freeze in that
position. Instead, observe the following:
1. Place the shift lever in “1” or “R” for manual trans-
mission vehicles, and in “P” for automatic transmis-
sion vehicles.
2. Use tire stops under the tires to prevent the ve-
hicle from moving.
When the vehicle is parked in snow or when it
snows, raise the wiper blades off the glass to pre-vent damage to them.
When the vehicle has been left parked after use on
roads heavily covered with snow, or has been left
parked during a snowstorm, icing may develop onthe brake system, which could cause poor braking
action. Check for snow or ice buildup on the sus-
pension, disc brakes and brake hoses underneath the vehicle.
If there is caked snow or ice, remove it, being care-ful not to damage the disc brakes and brake hoses
and ABS harness.

Appearance care
10-2
Exterior care Washing
The best way to preserve your vehicle ’s beauty is
frequent washing. Wash the vehicle at least once a
month to avoid contamination by road grime.
Wash dirt off with a wet sponge and plenty of luke-
warm or cold water. Do not wash the vehicle with hot
water and in direct sunlight.
Salt, chemicals, insects, tar, soot and bird droppings
should be washed off by using a light detergent, as
required. If you use a light detergent, make certain
that it is a neutral detergent. Do not use strong soap or chemical detergents. All cleaning agents should
be promptly flushed from the surface and not al-
lowed to dry there. Rinse the vehicle thoroughly with
plenty of lukewarm water. Wipe the remaining water
off with a chamois or soft cloth. NOTE When having your vehicle washed in an auto- matic car wash, make sure beforehand that thecar wash is of suitable type. If the vehicle is
equipped with a rear/roof spoiler or rear wiper, itmay be damaged by car wash brushes or otherequipment.
CAUTION
When washing the vehicle, the brakes may
get wet. As a result, the brake stopping dis-
tance will be longer. To dry the brakes, drivethe vehicle at a safe speed while lightly press- ing the brake pedal to heat up the brakes. Do not wash the engine compartment and
area adjacent to it. If water enters the engineair intake, electrical parts or the power steer-
ing fluid reservoir, it will cause engine trouble
or faulty power steering respectively.
Washing the underbody
Chemicals, salts and gravel used for deicing road
surfaces are extremely corrosive, accelerating the
corrosion of underbody components, such as theexhaust system, fuel and brake lines, brake cables,floor pan and fenders, and suspension.
Thoroughly flush the underbody and inside of the
fenders with lukewarm or cold water at frequent in-
tervals to reduce the harmful effects of such agents.
Using a warm water washer
Keep a good distance of 12 in (30 cm) or more
between the washer nozzle and the vehicle.

Maintenance and service
11-2
Tire inspection 11-41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tire pressures and wear 11-42 . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel balance 11-45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wear indicators 11-45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tire rotation 11-46
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tire replacement 11-47 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel replacement 11-48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel covers 11-49 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Aluminum wheels (If equipped) 11-50 . . . . . . . . . . . . . . . .
Windshield washer fluid 11-50 . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement of windshield wiper blades 11-51 . .
Battery 11-54
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuses 11-56
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main fuse 11-59
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation of accessories 11-60 . . . . . . . . . . . . . . . . . . . . . . .
Replacing bulbs 11-61 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlight 11-62
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front turn signal light and parking light 11-64 . . . . . .
Front fog light (if equipped) 11-68 . . . . . . . . . . . . . . . . . . . . .
Front side marker light 11-69 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear combination lights 11-70 . . . . . . . . . . . . . . . . . . . . . . . . . .
License plate light 11-72 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dome light, map light and cargo area light 11-73 . . .
Trunk light 11-74
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High mount stop light 11-74 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance and service
11-8
Engine compartment overview 2.5 liter model
1) Manual transmission oil level gauge
(MT) (page 11-25) or Differential
gear oil level gauge (AT) (page 11-29)
2) Air cleaner element (page 11-20)
3) Clutch fluid reservoir (page 11-35)
4) Automatic transmission fluid level gauge (page 11-27)
5) Brake fluid reservoir (page 11-34)
6) Windshield washer tank (page
11-50)
7) Fuse box (page 11-56)
8) Battery (page 11-54)
9) Engine oil filler cap (page 11-10)
10) Engine coolant reservoir (page 11-16)
11) Radiator cap (page 11-16)
12) Engine oil level gauge (page 11-10)
13) Power steering fluid reservoir (page 11-32)

Maintenance and service
11-9
– CONTINUED –
2.0 liter (Turbo) model
1) Manual transmission oil level
gauge (MT) (page 11-25) or
Differential gear oil level gauge
(AT) (page 11-29)
2) Air cleaner element (page 11-20)
3) Clutch fluid reservoir (page
11-35)
4) Automatic transmission fluid level gauge (page 11-27)
5) Brake fluid reservoir (page
11-34)
6) Windshield washer tank (page
11-50)
7) Fuse box (page 11-56)
8) Battery (page 11-54)
9) Engine oil filler cap (page 11-10)
10) Engine coolant reservoir (page
11-16)
11) Engine oil level gauge (page 11-10)
12) Radiator cap (page 11-16)
13) Power steering fluid reservoir (page 11-32)

Maintenance and service
11-50
Aluminum wheels (If equipped)
Aluminum wheels can be scratched and damaged
easily. Handle them carefully to maintain their ap-
pearance, performance, and safety. When any of the wheels is removed and replaced
for tire rotation or to change a flat, always check the
tightness of the wheel nuts after driving approxi-mately 600 miles (1,000 km). If any nut is loose,
tighten it to the specified torque. Never apply oil to the threaded parts, wheel nuts,
or tapered surface of the wheel. Never let the wheel rub against sharp protrusions
or curbs. Be sure to fit tire chains on uniformly and com-
pletely around the tire, otherwise the chains mayscratch the wheel. When wheel nuts, balance weights, or the center
cap is replaced, be sure to replace them with genu-
ine SUBARU parts designed for aluminum wheels. Windshield washer fluid
Check the level of the washer fluid at each fuel stop.
If the level is low, fill the fluid up to the neck of the
reservoir. Use windshield washer fluid. If windshield washer
fluid is unavailable use clean water.
In areas where water freezes in winter, use an anti-
freeze type windshield washer fluid. SUBARU Wind-
shield Washer Fluid contains 58.5% methyl alcohol
and 41.5% surfactant, by volume. Its freezing tem-
perature varies according to how much it is diluted,
as indicated below.