SUBARU LEGACY 1996 Service Repair Manual

B2M0397A
4. CHECK HARNESS CONNECTOR BETWEEN SUB
FAN RELAY-2 AND SUB FAN MOTOR.
1) Disconnect connectors from sub fan relay-2 and sub fan
motor.
2) Measure resistance of harness connector between sub
fan relay-2 and sub fan motor.
Connector & terminal / Specified resistance:
(F29) No. 4—(F16) No. 3 / 10Ω, max.
B2M0398A
5. CHECK GROUND CIRCUIT OF SUB FAN MOTOR.
Measure resistance between sub fan motor connector and
body.
Connector & terminal / Specified resistance:
(F16) No. 1—Body / 10Ω, max.
B2M0368A
6. CHECK SUB FAN MOTOR.
1) Disconnect connector from sub fan motor.
2) Connect battery positive (+) terminal to terminals No. 2
and No.3, and connect terminal No. 1 to ground. Ensure
that fan rotates at HI speed.
35
2-5DIAGNOSTICS
3. Radiator Sub Fan (With A/C model only)

1. Intake Manifold
B2M0739A

1Intake manifold gasket LH
(2200 cc model)


2Intake manifold gasket RH
(2200 cc model)


3Intake manifold gasket LH
(2500 cc model)


4Intake manifold gasket RH
(2500 cc model)


5Fuel injector pipe insulator


6Fuel injector pipe


7O-ring A


8O-ring B


9Fuel injector


10Insulator


11Fuel injector cap


12Plate


13Sealing

14Gasket


15Engine coolant hose B


16Air by-pass hose


17Idle air control solenoid valve


18Engine coolant hose A


19Nipple (AT model)


20Plug


21PCV valve


22Purge control solenoid valve


23Nipple


24BPT


25BPT holder bracket


26Back pressure hose


27EGR vacuum hose A


28EGR vacuum pipe


29EGR vacuum hose C


30EGR valve

31Gasket


32EGR vacuum hose B


33EGR solenoid valve


34EGR pipe


35Collar


36Intake manifold
Tightening torque: N⋅m (kg-m, ft-lb)
T1: 3.4±0.5 (0.35±0.05, 2.5±0.4)
T2: 6.4±0.5 (0.65±0.05, 4.7±0.4)
T3: 16±1.5 (1.6±0.15, 11.6±1.1)
T4: 19±1 (1.9±0.1, 13.7±0.7)
T5: 19±1.5 (1.9±0.15, 13.7±1.1)
T6: 23±3 (2.3±0.3, 16.6±2.2)
T7: 25±2 (2.5±0.2, 18.1±1.4)
T8: 34±2 (3.5±0.2, 25.3±1.4)
2
2-7COMPONENT PARTS
1. Intake Manifold

2. Air Intake System
B2M0152A

1Gasket


2Throttle position sensor


3Throttle body


4Clamp


5Air intake duct


6By-pass hose
Tightening torque: N⋅m (kg-m, ft-lb)
T1: 2.2±0.2 (0.22±0.02, 1.6±0.1)
T2: 22±2 (2.2±0.2, 15.9±1.4)
3
2-7COMPONENT PARTS
2. Air Intake System

3. Air Cleaner
B2M0153A

1Mass air flow sensor bracket


2Mass air flow sensor ASSY


3Air cleaner upper cover


4Air cleaner element


5Spacer


6Bush


7Clip


8Air cleaner case


9Cushion rubber

10Air intake duct


11Resonator chamber ASSY


12Clip
Tightening torque: N⋅m (kg-m, ft-lb)
T1: 7.4±2.0 (0.75±0.2, 5.4±1.4)
T2: 33±10 (3.4±1.0, 25±7)
4
2-7COMPONENT PARTS
3. Air Cleaner

B2M0154
1. Air Cleaner and Air Intake Duct
A: REMOVAL AND INSTALLATION
1) Loosen clamp which connect air intake duct to throttle
body and mass air flow sensor.
2) Disconnect blow-by hoses from air intake duct.
3) Remove air intake duct.
G2M0305
4) Disconnect connector from mass air flow sensor.
G2M0390
5) Remove clips of air cleaner upper cover.
6) Remove air cleaner element.
G2M0391
7) Remove air cleaner lower case.
8) Installation is in the reverse order of removal.
5
2-7SERVICE PROCEDURE
1. Air Cleaner and Air Intake Duct

B2M0154
2. Mass Air Flow Sensor
A: REMOVAL AND INSTALLATION
1) Remove air intake duct.
G2M0305
2) Disconnect connector from mass air flow sensor.
G2M0390
3) Remove air cleaner upper cover.
G2M0393
4) Remove mass air flow sensor from air cleaner upper
cover.
5) Installation is in the reverse order of removal.
Tightening torque:
7.4±2.0 N⋅m (0.75±0.2 kg-m, 5.4±1.4 ft-lb)
6
2-7SERVICE PROCEDURE
2. Mass Air Flow Sensor

B2M0154
3. Throttle Body
A: REMOVAL AND INSTALLATION
1) Remove air intake duct.
G2M0280
2) Disconnect accelerator cable
1.
3) Disconnect cruise control cable

2. (With cruise control
model)
B2M0155
4) Disconnect connector from throttle position sensor.
B2M0156
5) Disconnect engine coolant hoses from throttle body.
B2M0157
6) Remove bolts which install throttle body to intake mani-
fold.
7) Installation is in the reverse order of removal.
CAUTION:
Always use a new gasket.
Tightening torque:
22±2 N⋅m (2.2±0.2 kg-m, 15.9±1.4 ft-lb)
7
2-7SERVICE PROCEDURE
3. Throttle Body

B2M0154
4. Intake Manifold
A: REMOVAL
1) Release fuel pressure. <Ref. to 2-8 [W1A0].>
2) Disconnect connector from mass air flow sensor.
3) Remove air intake duct, air cleaner upper cover and air
cleaner element.
G2M0280
4) Disconnect accelerator cable
1.
5) Disconnect cruise control cable

2. (With cruise control
model)
B2M0334
6) Disconnect hoses from pressure sources switching
solenoid valve.
G2M0286
7) Remove power steering pump from bracket.
(1) Loosen lock bolt and slider bolt, and remove front
side V-belt.
B2M0340
(2) Remove pipe with bracket from intake manifold.
8
2-7SERVICE PROCEDURE
4. Intake Manifold

B2M0334
(3) Remove bolts which install power steering pump
from bracket.
B2M0029
(4) Place power steering pump on the right side wheel
apron.
B6M0160
8) Disconnect spark plug cords from ignition coil.
H2M1246
9) Disconnect engine coolant hoses from throttle body.
H2M1259A
10) Disconnect engine coolant hose
1from idle air con-
trol solenoid valve.
11) Disconnect air by-pass hose

2from idle air control
solenoid valve.
9
2-7SERVICE PROCEDURE
4. Intake Manifold

B2M0342
12) Disconnect brake booster hose.
B2M0343
13) Remove EGR pipe.
G2M0370
14) Disconnect canister hose from pipe.
B2M0019
15) Disconnect engine harness connectors from bulkhead
harness connectors.
B2M0345A
16) Disconnect connectors from engine coolant tempera-
ture sensor

1and thermometer
2.
10
2-7SERVICE PROCEDURE
4. Intake Manifold