SUBARU LEGACY 1997 Service Repair Manual

I: TROUBLE CODE 44
—A COMBINATION OF AT CONTROL
ABNORMALS—
DIAGNOSIS:

Combination of AT control faults
TROUBLE SYMPTOM:

ABS does not operate.
8I1.Check specifications of the ABSCM.
8I2.Check ground short of harness.
8I3.Check battery short of harness.
8I4.Check AT control module.
8I5.Check open circuit of harness.
8I6.Check poor contact in connector between AT
control module and ABSCM.
8I7.Check ABSCM.






66
4-4cBRAKES [ABS 5.3 TYPE]
8. Diagnostics Chart with Trouble Code

WIRING DIAGRAM:
B4M1040
B4M0910A
8I1CHECK SPECIFICATIONS OF THE
ABSCM.
Check specifications of the plate attached to the ABSCM.
: Is an ABSCM for AT model installed on a MT
model?
: Replace ABSCM.
: Go to step8I2.
67
4-4cBRAKES [ABS 5.3 TYPE]
8. Diagnostics Chart with Trouble Code

B4M0846A
8I2
CHECK GROUND SHORT OF HARNESS.
1) Turn ignition switch to OFF.
2) Disconnect two connectors from AT control module.
3) Disconnect connector from ABSCM.
4) Measure resistance between ABSCM connector and
chassis ground.
: Connector & terminal
(F49) No. 12—Chassis ground
Is resistance more than 1 MΩ?
: Go to step8I3.
: Repair harness between AT control module and
ABSCM.
B4M0847A
8I3
CHECK BATTERY SHORT OF HARNESS.
1) Turn ignition switch to ON.
2) Measure voltage between ABSCM connector and chas-
sis ground.
: Connector & terminal
(F49) No. 12 (+)—Chassis ground ()
Is voltage 0 V?
: Go to next step.
: Repair harness between AT control module and
ABSCM.
3) Turn ignition switch to OFF.
4) Measure voltage between ABSCM connector and chas-
sis ground.
: Connector & terminal
(F49) No. 12 (+)—Chassis ground ()
Is voltage 0 V?
: Go to step8I4.
: Repair harness between AT control module and
ABSCM.
68
4-4cBRAKES [ABS 5.3 TYPE]
8. Diagnostics Chart with Trouble Code

B4M0848B
8I4
CHECK AT CONTROL MODULE.
1) Connect all connectors to AT control module.
2) Turn ignition switch to ON.
3) Measure voltage between AT control module connector
terminals.
: Connector & terminal
(B55) No. 1 (+)—(B56) No. 5 ()
Is voltage 10—13 V?
: Go to step8I5.
: Go to next step.
B4M0849B
4) Measure voltage between AT control module connector
and chassis ground.
: Connector & terminal
(B54) No. 6 (+)—Chassis ground ()
(B55) No. 1 (+)—Chassis ground ()
Is voltage 10—13 V?
: Replace AT control module.
: Repair harness connector between battery, igni-
tion switch and AT control module.
B4M0844A
8I5
CHECK OPEN CIRCUIT OF HARNESS.
Measure voltage between ABSCM connector and chassis
ground.
: Connector & terminal
(F49) No. 12 (+)—Chassis ground ()
(F49) No. 39 (+)—Chassis ground ()
Is voltage 10—13 V?
: Go to step8I6.
: Repair harness connector between AT control
module and ABSCM.
69
4-4cBRAKES [ABS 5.3 TYPE]
8. Diagnostics Chart with Trouble Code

8I6CHECK POOR CONTACT IN CONNEC-
TOR BETWEEN AT CONTROL MODULE
AND ABSCM.
: Is there poor contact in connectors between
AT control module and ABSCM?
: Repair connector.
: Go to step8I7.
8I7
CHECK ABSCM.
1) Connect all connectors.
2) Erase the memory.
3) Perform inspection mode.
4) Read out the trouble code.
: Is the same trouble code as in the current
diagnosis still being output?
: Replace ABSCM.
: Go to next.
: Are other trouble codes being output?
: Proceed with the diagnosis corresponding to the
trouble code.
: A temporary poor contact.
70
4-4cBRAKES [ABS 5.3 TYPE]
8. Diagnostics Chart with Trouble Code

J: TROUBLE CODE 46
—ABNORMAL G SENSOR POWER SUPPLY
VOLTAGE—
DIAGNOSIS:

Faulty G sensor power supply voltage
TROUBLE SYMPTOM:

ABS does not operate.
8J1.Check G sensor.
8J2.Check ground short of G sensor.
8J3.Check short of harness between ABSCM and
G sensor.
8J4.Check ground short of harness.
8J5.Check battery short of harness.
8J6.Check poor contact in connector between
ABSCM and G sensor.
8J7.Check ABSCM.






71
4-4cBRAKES [ABS 5.3 TYPE]
8. Diagnostics Chart with Trouble Code

WIRING DIAGRAM:
B4M1047
B4M0851B
8J1
CHECK G SENSOR.
1) Turn ignition switch to OFF.
2) Remove console box.
3) Disconnect connector from G sensor.
4) Measure resistance of G sensor.
: Connector & terminal
To (P11) No. 1—No. 3
Is resistance 50±8 kΩ?
: Go to step8J2.
: Replace G sensor.
72
4-4cBRAKES [ABS 5.3 TYPE]
8. Diagnostics Chart with Trouble Code

B4M0852B
8J2
CHECK GROUND SHORT OF G SENSOR.
Measure resistance between G sensor and bracket.
: Connector & terminal
To (P11) No. 3—Bracket
Is resistance more than 1 MΩ?
: Go to step8J3.
: Replace G sensor.
B4M0853A
8J3CHECK SHORT OF HARNESS BETWEEN
ABSCM AND G SENSOR.
1) Disconnect connector from ABSCM.
2) Measure resistance between ABSCM connector termi-
nals.
: Connector & terminal
(F49) No. 45—No. 8
Is resistance more than 1 MΩ?
: Go to step8J4.
: Repair harness between ABSCM and G sensor.
B4M0854A
8J4
CHECK GROUND SHORT OF HARNESS.
Measure resistance between ABSCM connector and chas-
sis ground.
: Connector & terminal
(F49) No. 8—Chassis ground
(F49) No. 45—Chassis ground
Is resistance more than 1 MΩ?
: Go to step8J5.
: Repair harness between ABSCM and G sensor.
73
4-4cBRAKES [ABS 5.3 TYPE]
8. Diagnostics Chart with Trouble Code

B4M0855A
8J5
CHECK BATTERY SHORT OF HARNESS.
1) Turn ignition switch to ON.
2) Measure voltage between ABSCM connector and chas-
sis ground.
: Connector & terminal
(F49) No. 8 (+)—Chassis ground ()
(F49) No. 45 (+)—Chassis ground ()
Is voltage 0 V?
: Go to next step.
: Repair harness between ABSCM and G sensor.
3) Turn ignition switch to OFF.
4) Measure voltage between ABSCM and chassis ground.
: Connector & terminal
(F49) No. 8 (+)—Chassis ground ()
(F49) No. 45 (+)—Chassis ground ()
Is voltage 0 V?
: Go to step8J6.
: Repair harness between ABSCM and chassis
ground.
8J6CHECK POOR CONTACT IN CONNEC-
TOR BETWEEN ABSCM AND G SENSOR.
: Is there poor contact in connectors between
ABSCM and G sensor?
: Repair connector.
: Go to step8J7.
8J7
CHECK ABSCM.
1) Connect all connectors.
2) Erase the memory.
3) Perform inspection mode.
4) Read out the trouble code.
: Is the same trouble code as in the current
diagnosis still being output?
: Replace ABSCM.
: Go to next.
: Are other trouble codes being output?
: Proceed with the diagnosis corresponding to the
trouble code.
: A temporary poor contact.
74
4-4cBRAKES [ABS 5.3 TYPE]
8. Diagnostics Chart with Trouble Code

K: TROUBLE CODE 51
—ABNORMAL VALVE RELAY—
DIAGNOSIS:

Faulty valve relay
TROUBLE SYMPTOM:

ABS does not operate.
8K1.Check resistance of valve relay.
8K2.Check contact point of valve relay.
8K3.Check short of valve relay.
8K4.Check power supply voltage at valve relay
contact point.
8K5.Check ground circuit of relay box.
8K6.Check broken wire and ground short in power
supply circuit of relay box.
8K7.Check broken wire in contact point circuit of
relay box.
8K8.Check ground short in contact point circuit of
relay box.
8K9.Check battery short in contact point circuit of
relay box.
8K10.Check diode of relay box.
8K11.Check broken wire in ground circuit of relay
box.
8K12.Check battery short in ground circuit of relay
box.
8K13.Check broken wire in control circuit of relay
box.
8K14.Check ground short in control circuit of relay
box.
8K15.Check battery short in control circuit of relay
box.
Continues to next page.















75
4-4cBRAKES [ABS 5.3 TYPE]
8. Diagnostics Chart with Trouble Code