SUBARU LEGACY 1999 Service Repair Manual

2. Oil Pump
B3M0876A
(1) Oil pump rotor
(2) Oil pump cover
(3) Seal ring
(4) Thrust needle bearing
(5) Drive pinion shaft
(6) Roller bearing
(7) Shim
(8) Oil pump housing
(9) Nipple
(10) Air breather hose
(11) Gasket(12) O-ring
(13) Test plug
(14) Stud bolt
(15) O-ring
(16) O-ring
(17) Oil seal retainer
(18) Oil seal
(19) O-ring
(20) Drive pinion collar
(21) Lock nutTightening torque: N´m (kg-m, ft-lb)
T1:
7±1 (0.7±0.1, 5.1±0.7)
T2:13±1 (1.3±0.1, 9.4±0.7)
T3:18±5 (1.8±0.5, 13.0±3.6)
T4:25±2 (2.5±0.2, 18.1±1.4)
T5:39±3 (4.0±0.3, 28.9±2.2)
T6:41±3 (4.2±0.3, 30.4±2.2)
T7:121±5 (12.3±0.5, 89.0±3.6)
16
3-2[C200]COMPONENT PARTS
2. Oil Pump

MEMO:
17
[C200]3-2COMPONENT PARTS
2. Oil Pump

3. Transmission Case and Control Device
B3M0878A
18
3-2[C300]COMPONENT PARTS
3. Transmission Case and Control Device

(1) Oil level gauge
(2) Oil charger pipe
(3) O-ring
(4) Transfer valve plate
(5) Transfer valve ASSY
(6) Transfer clutch seal
(7) Duty solenoid C (Transfer)
(8) Straight pin
(9) Return spring
(10) Shaft
(11) Parking pawl
(12) Parking support
(13) Inlet filter
(14) Gasket
(15) Inlet pipe
(16) Union screw
(17) O-ring
(18) Test plug
(19) Oil filter(20) Oil filter stud bolt
(21) Drain plug
(22) Gasket
(23) Oil pan
(24) Magnet
(25) Stud bolt (Short)
(26) Stud bolt (Long)
(27) Parking rod
(28) Manual plate
(29) Spring pin
(30) Detention spring
(31) Ball
(32) Spring
(33) Gasket
(34) Outlet pipe
(35) Union screw
(36) Oil seal
(37) Select lever
(38) Inhibitor switch ASSY(39) Nipple
(40) Air breather hose
(41) Transmission case
(42) Plate ASSY
(43) Washer
Tightening torque: N´m (kg-m, ft-lb)
T1:
3.4±0.5 (0.35±0.05, 2.5±0.4)
T2:4.9±0.5 (0.50±0.05, 3.6±0.4)
T3:5.9±1.0 (0.60±0.10, 4.3±0.7)
T4:7.8±1.0 (0.80±0.10, 5.8±0.7)
T5:12.7±1.0 (1.30±0.10, 9.4±0.7)
T6:13.7±2.0 (1.4±0.2, 10.1±1.4)
T7:17.7±2.9 (1.80±0.30, 13.0±2.2)
T8:24.5±2.0 (2.50±0.20, 18.1±1.4)
T9:24.5±2.9 (2.5±0.3, 18.1±2.2)
T10:34.3±2.9 (3.50±0.30, 25.3±2.2)
19
[C300]3-2COMPONENT PARTS
3. Transmission Case and Control Device

4. Control Valve and Harness Routing
B3M0928A
(1) Stay
(2) Transmission harness
(3) O-ring
(4) O-ring
(5) Torque converter turbine speed
sensor
(6) O-ring
(7) Vehicle speed sensor 2 (Front)
(8) O-ring
(9) Vehicle speed sensor 1 (Rear)
(10) Upper valve body
(11) Accumulator piston(12) Accumulator spring
(13) Side plate
(14) Separate plate
(15) Middle valve body
(16) Separate plate
(17) Fluid filter
(18) Fluid filter
(19) Lower valve body
(20) Shift solenoid 2
(21) Shift solenoid 1
(22) 2-4 brake timing solenoid
(23) Duty solenoid D (2-4 brake)(24) ATF temperature sensor
(25) Duty solenoid A (Line pressure)
(26) Low clutch timing solenoid
(27) Duty solenoid B (Lock-up)
(28) Oil strainer
Tightening torque: N´m (kg-m, ft-lb)
T1:
7±1 (0.7±0.1, 5.1±0.7)
T2:8±1 (0.8±0.1, 5.8±0.7)
20
3-2[C400]COMPONENT PARTS
4. Control Valve and Harness Routing

5. High Clutch and Reverse Clutch
B3M1179A
(1) High clutch drum
(2) Lip seal
(3) Lathe cut seal ring
(4) Reverse clutch piston
(5) Lathe cut seal ring
(6) Lathe cut seal ring
(7) High clutch piston
(8) Spring retainer(9) Cover
(10) Snap ring
(11) Driven plate (Thicker)
(12) Driven plate (Thinner)
(13) Drive plate
(14) Retaining plate
(15) Snap ring
(16) Dish plate(17) Driven plate
(18) Drive plate
(19) Retaining plate
(20) Snap ring
(21) Thrust needle bearing
(22) High clutch hub
21
[C500]3-2COMPONENT PARTS
5. High Clutch and Reverse Clutch

6. Planetary Gear and 2-4 Brake
B3M1178A
(1) Thrust needle bearing
(2) Front sun gear
(3) Thrust needle bearing
(4) Snap ring
(5) Front planetary carrier
(6) Thrust needle bearing
(7) Rear sun gear
(8) Thrust needle bearing
(9) Rear planetary carrier(10) Washer
(11) Thrust needle bearing
(12) Rear internal gear
(13) Washer
(14) Snap ring
(15) Retaining plate
(16) Drive plate
(17) Driven plate
(18) Pressure rear plate(19) Snap ring
(20) Spring retainer
(21) 2-4 brake piston
(22) Lathe cut seal ring
(23) Lathe cut seal ring
(24) 2-4 brake piston retainer
(25) 2-4 brake seal
(26) Leaf spring
22
3-2[C600]COMPONENT PARTS
6. Planetary Gear and 2-4 Brake

7. Low Clutch and Low & Reverse Brake
B3M1017A
(1) Retaining plate
(2) Drive plate
(3) Driven plate
(4) Dish plate
(5) Snap ring
(6) Cover
(7) Spring retainer
(8) Lathe cut seal ring
(9) Low piston
(10) Lathe cut seal ring
(11) Low clutch drum(12) Needle bearing
(13) Snap ring
(14) One-way clutch
(15) Snap ring
(16) Thrust needle bearing
(17) Seal ring
(18) Needle bearing
(19) One-way clutch inner race
(20) Socket bolt
(21) Spring retainer
(22) Return spring(23) Snap ring
(24) Retaining plate
(25) Leaf spring
(26) Drive plate
(27) Driven plate
(28) Dish plate
(29) Low and reverse brake piston
Tightening torque: N´m (kg-m, ft-lb)
T:
25±2 (2.5±0.2, 18.1±1.4)
23
[C700]3-2COMPONENT PARTS
7. Low Clutch and Low & Reverse Brake

8. Reduction Gear
B3M0882A
(1) Seal ring
(2) Ball bearing
(3) Reduction drive gear
(4) Reduction drive shaft
(5) Plug(6) Drive pinion shaft
(7) Snap ring
(8) Ball bearing
(9) Reduction driven gear
(10) Washer(11) Lock nut
Tightening torque: N´m (kg-m, ft-lb)
T:
100±5 (10.2±0.5, 73.8±3.6)
24
3-2[C800]COMPONENT PARTS
8. Reduction Gear

9. Differential Case
B3M1019A
(1) Crown gear
(2) Pinion shaft
(3) Differential case (RH)
(4) Straight pin
(5) Differential case (LH)
(6) Taper roller bearing
(7) Oil seal(8) O-ring
(9) Differential side retainer
(10) Circlip
(11) Lock plate
(12) Axle shaft
(13) Washer
(14) Differential bevel pinion(15) Differential bevel gear
Tightening torque: N´m (kg-m, ft-lb)
T1:
25±2 (2.5±0.2, 18.1±1.4)
T2:62±5 (6.3±0.5, 45.6±3.6)
25
[C900]3-2COMPONENT PARTS
9. Differential Case