ESP SUBARU OUTBACK 2000 3.G Owner's Manual

Page 279 of 413

Driving tips8-13

CONTINUED –
n
Wiper operation when snowing
Before d riving in c old weather, make sure the wip er b lad es are not
frozen to the wind shield or rear wind ow. If the wip er b lad es are frozen
to the wind shield or rear wind ow, use the d efroster with the airflow
c ontrol d ial in the “
” p osition and the temp erature c ontrol d ial set
for maximum warmth until the wip er b lad es are c omp l etely thawed
out. If your vehic le is eq uip p ed with a wip er d eic e r, it is help ful to thaw
the wind shield wip er b lad es. To thaw out the rear w ip er b lad e, use the
rear wind ow d efog g er.
When d riving in snow, if frozen snow starts to stic k on the surfac e of
the wind shield d esp ite wip er op eration, use the d ef roster with the air-
flow c ontrol d ial in “
” and the temp erature c ontrol d ial set for max-
imum warmth. After the wind shield g ets warmed enoug h to melt the
frozen snow on it, wash it away using the wind shiel d washer.
Snow stuc k on the wip er arm p revents the wip er from working effec -
tively. If snow is stuc k on the wip er arm, p ull off the road to a safe
p lac e, then remove it. If you stop the c ar at road sid e, use the hazard
warning flasher to alert other d rivers.
We rec ommend use of non-freezing typ e wip er b lad es d uring the sea-
sons you c ould have snow and sub -zero temp eratures. Corrosion protection
Refer to the “Corrosion p rotec tion ” sec tion (c hap ter 10).
Snow tires
WARNING
When replacing a tire, make sure you use only the same size,
circumferences, construction, brand, and load range as the origi- nal tires listed on the tire placard. Using other sizes, circumfer-
ences or construction may result in severe mechanical damageto the drive train of your vehicle and may affect ride, handling,braking, speedometer/odometer calibration, and clearancebetween the body and tires. It also may be dangerous and lead toloss of vehicle control.

Page 292 of 413

8-26Trailer towing
Your c ar is d esig ned and intend ed to b e used p rimar
ily as a p asseng er-
c arrying vehic le. Towing a trailer p uts ad d itional load s on your c ar’s en-
g ine, d rivetrain, b rakes, tires and susp ension and has an ad verse effec t
on fuel ec onomy.
If you d o d ec id e to tow a trailer, your safety and satisfac tion d ep end
up on p rop er use of c orrec t eq uip ment and c autious o p eration of your ve-
hic le. Seek the ad vic e of your SUBARU d ealer to ass ist you in p urc has-
ing a hitc h and other nec essary towing eq uip ment ap p rop riate for your
vehic le. In ad d ition, b e sure to follow the instruc tions on c orrec t installa-
tion and use p rovid ed b y the trailer and other towi ng eq uip ment
manufac turers.
SUBARU assumes no resp onsib ility for injuries or ve hic le d amag e that
result from trailer towing eq uip ment, or from any e rrors or omissions in
the instruc tions ac c omp anying suc h eq uip ment or for your failure to fol-
low the p rop er instruc tions.
Warranties and maintenance
SUBARU warranties d o not ap p ly to vehic le d amag e or malfunc tion
c aused b y trailer towing . If you use your vehic le t o tow a trailer, more
freq uent maintenanc e will b e req uired d ue to the ad d itional load .
(Refer to “Maintenanc e sc hed ule und er severe d riving c ond ition s” in
the “Warranty and Maintenanc e Booklet ”.)
Und er no c irc umstanc es should a trailer b e towed wi th a new vehic le
or a vehic le with any new p owertrain c omp onent (eng ine, transmis-
sion, d ifferential, wheel b earing s, etc .) for the f irst 1,000 miles (1,600
km) of d riving . Maximum load limits
WARNING
Never exceed the maximum load limits explained below. Exceed- ing the maximum load limits could cause personal injury and/or
vehicle damage.

Page 295 of 413

Driving tips8-29

CONTINUED –
HBF019BB
Gross Axle Weight
OM-H2784
To c hec k b oth GVWR and GAWR and to c onfirm that the total weig ht
and weig ht d istrib ution are within safe d riving lim its, you should have
your vehic le and trailer weig hed at a c ommerc ial we ig hing station.
Be sure that all c arg o is firmly sec ured to p revent a c hang e in weig ht
d istrib ution while d riving . n Tongue load
WARNING
If the trailer is loaded with more weight in the back of trailer ’s
axle than in the front, the load is taken off the rear axle of the tow- ing vehicle. This may cause the rear wheels to skid, especiallyduring braking or when vehicle speed is reduced during corner-
ing, resulting in over-steer, spin out and/or jackknifing.
Ensure that the trailer tong ue load is from 8 to 11 p erc ent of the total
trailer weig ht and d oes not exc eed the maximum valu e of 200 lb s (90
kg ).
The tong ue load c an b e weig hed with a b athroom sc al e as shown in
the illustration b elow. When weig hing the tong ue lo ad , b e sure to p osi-
tion the towing c oup ler at the heig ht at whic h it w ould b e d uring
ac tual towing , using a jac k as shown.

Page 333 of 413

10-2Exterior care
Washing
CAUTION
When washing the vehicle, the brakes may get wet. As a result,
the brake stopping distance will be longer. To dry the brakes, drive the vehicle at a safe speed while lightly pressing the brakepedal to heat up the brakes. Do not wash the engine compartment and areas adjacent to it.
If water enters the engine air intake, electrical parts or the power
steering fluid reservoir, it will cause engine trouble or faulty
power steering respectively.
The b est way to p reserve your vehic le ’s b eauty is freq uent washing .
Wash the vehic le at least onc e a month to avoid c on tamination b y road
g rime.
Wash d irt off with a wet sp ong e and p lenty of lukew arm or c old water. Do
not wash the vehic le with hot water and in d irec t s unlig ht.
Salt, c hemic als, insec ts, tar, soot and b ird d rop p i ng s should b e washed
off b y using a lig ht d eterg ent, as req uired . If you use a lig ht d eterg ent,
make c ertain that it is a neutral d eterg ent. Do not use strong soap or
c hemic al d eterg ents. All c leaning ag ents should b e p romp tly flushed
from the surfac e and not allowed to d ry there. Rins e the vehic le thor-
oug hly with p lenty of lukewarm water. Wip e the rema ining water off with a
c hamois or soft c loth. NOTE When having your vehicle washed in an automatic car wash, make
sure beforehand that the car wash is of suitable type. If the vehicle
is equipped with a rear/roof spoiler, it may be damaged by car washbrushes or other equipment.

Page 337 of 413

10-62. It is d riven in areas of hig h humid ity, esp ec iall
y when temp eratures
rang e just ab ove freezing .
3. Damp ness in c ertain p arts of the vehic le remains for a long time,
even thoug h other p arts of the vehic le may b e d ry.
4. Hig h temp eratures will c ause c orrosion to p arts o f the vehic le
whic h c annot d ry q uic kly d ue to lac k of p rop er vent ilation.
To help prevent corrosion
Wash the vehic le freq uently. If you d rive on salted road s in the winter
or if you live in a c oastal area, you should flush the und erb od y with
fresh water freq uently.
After the winter has end ed , it is rec ommend ed that the und erb od y b e
g iven a very thoroug h washing .
Before the b eg inning of winter, c hec k the c ond ition of und erb od y
c omp onents, suc h as the exhaust system, fuel and b r ake lines, b rake
c ab les, susp ension, steering system, floor p an, and fend ers. If any of
them are found to b e rusted , they should b e g iven a n ap p rop riate rust
p revention treatment or should b e rep lac ed . Contac t your SUBARU
d ealer to p erform this kind of maintenanc e and trea tment if you need
assistanc e.
Rep air c hip s and sc ratc hes in the p aint as soon as you find them.
Chec k the interior of the vehic le for water and d ir t ac c umulation und er
the floor mats b ec ause that c ould c ause c orrosion. Oc c asionally
c hec k und er the mats to make sure the area is d ry.
Keep your g arag e d ry. Do not p ark your vehic le in a d amp , p oorly
ventilated g arag e. In suc h a g arag e, c orrosion c an b e c aused b y
d amp ness. If you wash the vehic le in the g arag e or p ut the vehic le
into the g arag e when wet or c overed with snow, that c an c ause
d amp ness.
If your vehic le is op erated in c old weather and /or in areas where road
salts and other c orrosive materials are used , the d oor hing es and
loc ks, trunk lid loc k, and hood latc h should b e ins p ec ted and lub ri-
c ated p eriod ic ally.

Page 352 of 413

Maintenance and service11-13

CONTINUED –
Cooling system
WARNING
Never attempt to remove the radiator cap until the engine has
been shut off and has cooled down completely. Since the coolantis under pressure, you may suffer serious burns from a spray ofboiling hot coolant when the cap is removed.
CAUTION
The cooling system has been filled at the factory with a high
quality, corrosion-inhibiting, year-around coolant which providesprotection against freezing down to –33F ( –36 C). For adding,
use genuine SUBARU coolant or an equivalent: a mixture of 50%
soft water and 50% ethylene-glycol basis coolant. Use of improp-er coolants may result in corrosion in the cooling system. It is im-portant to maintain protection against freezing and corrosion,
even if freezing temperatures are not expected. Never mix differ-ent kinds of coolant. Do not splash the engine coolant over painted parts. The alco-
hol contained in the engine coolant may damage the paint sur-face.
Hose and connections
Your vehic le emp loys an elec tric c ooling fan whic h is thermostatic ally
c ontrolled to op erate when the eng ine c oolant reac h es a sp ec ific tem-
p erature.
If the rad iator c ooling fan d oes not op erate even w hen the eng ine
c oolant temp erature g aug e exc eed s the normal op erat ing rang e, the
c ooling fan c irc uit may b e d efec tive. Chec k the fus e and rep lac e it if
nec essary. If the fuse is not b lown, have the c ooli ng system c hec ked
b y your SUBARU d ealer.
If freq uent ad d ition of c oolant is nec essary, there may b e a leak in the
eng ine c ooling system. It is rec ommend ed that the c ooling system
and c onnec tions b e c hec ked for leaks, d amag e, or lo oseness.

Page 372 of 413

Maintenance and service11-33

CONTINUED –
Replacement of brake pad and lining
CAUTION
If you continue to drive despite the scraping noise from the audi-
ble brake pad wear indicator, it will result in the need for costlybrake rotor repair or replacement.
OM-H0163
The front d isc b rakes and the rig ht rear d isc b rake have an aud ib le wear
ind ic ators on the b rake p ad s. If the b rake p ad s wea r c lose to their ser-
vic e limit, the wear ind ic ator makes a very aud ib le sc rap ing noise when
the b rake p ed al is ap p lied .
If you hear this sc rap ing noise eac h time you ap p ly the b rake p ed al,
have the b rake p ad s servic ed b y your SUBARU d ealer as soon as p os-
sib le.
Breaking-in of new brake pads and linings
When rep lac ing the b rake p ad or lining , use only g e nuine SUBARU
p arts. After rep lac ement, the new p arts must b e b ro ken in as follows:
n Brake pad and lining
While maintaining a sp eed of 30 to 40 mp h (50 to 65 km/h), step on
the b rake p ed al lig htly. Rep eat this five or more t imes.

Page 383 of 413

11-44two fuse b oxes. The one is loc ated und er the instru
ment p anel b ehind
the c oin tray on the d river ’s seat sid e. The other one is housed in the
eng ine c omp artment. The fuse p uller and sp are fuses are stored in the
main fuse b ox c over in the eng ine c omp artment.
If any lig hts, ac c essories or other elec tric al c ont rols d o not op erate, in-
sp ec t the c orresp ond ing fuse. If a fuse has b lown, rep lac e it.
HS0208
HS0204
Good
BlownFuse puller
Spare fuses
1. Turn the ig nition switc h to the “LOCK ” p osition and turn off all elec tri-
c al ac c essories.
2. Remove the c over.
(For b ehind the c oin tray: op en the c oin tray and p ull it horizontally to
remove it.)
3. Determine whic h fuse may b e b lown. The b ac k sid e of eac h fuse b ox
c over and the “Fuse and c irc uits ” sec tion in c hap ter 12 in this manual
show the c irc uit for eac h fuse.
HS0207
Fuse puller

Page 412 of 413

Consumer information and Reporting safety defects13-3

CONTINUED –
p halt and c onc rete. A tire marked C may have p oor t
rac tion p erfor-
manc e.
WARNING
The traction grade assigned to this tire is based on straight-
ahead braking traction tests, and does not include acceleration,cornering, hydroplaning, or peak traction characteristics.
Temperature A, B, C
The temp erature g rad es are A (the hig hest), B, and C, rep resenting the
tire ’s resistanc e to the g eneration of heat and its ab il ity to d issip ate heat
when tested und er c ontrolled c ond itions on a sp ec if ied ind oor lab oratory
test wheel. Sustained hig h temp erature c an c ause th e material of the tire
to d eg enerate and red uc e tire life, and exc essive t emp erature c an lead
to sud d en tire failure. The g rad e C c orresp ond s to a level of p erfor-
manc e whic h all p asseng er c ar tires must meet und er the Fed eral Motor
Vehic le Safety Stand ard s No. 109. Grad es B and A re p resent hig her lev-
els of p erformanc e on the lab oratory test wheel tha n the minimum re-
q uired b y law.
WARNING
The temperature grade for this tire is established for a tire that isproperly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, either separately or in combina-tion, can cause heat buildup and possible tire failure.

Page:   < prev 1-10 11-20 21-30