stop start SUBARU OUTBACK 2000 3.G Owner's Manual

Starting and operating7-15
–
CONTINUED –

Selector lever for automatic transmission
HB7021BB
HB7010AA
The selec tor lever has seven p ositions.
P (Park)
This p osition is for p arking the vehic le and starti ng the eng ine.
In this p osition, the transmission is mec hanic ally loc ked to p revent the
vehic le from rolling freely.
When you p ark the vehic le, first set the p arking b r ake fully, then shift
into the “P ” p osition. Do not hold the vehic le with only the tr ansmis-
sion.
A shift interloc k func tion is emp loyed in the autom atic transmission
system to ensure safe starting of the vehic le.
To shift the selec tor lever from the “P ” to the any other p osition, you
have to d ep ress the b rake p ed al fully when the ig ni tion switc h is in the
“ ON ” p osition. This p revents the vehic le from lurc hing when it is
started .
If the shift lever d oes not move from the “P ” p osition with the b rake
p ed al d ep ressed , refer to the “Shift loc k release ” sec tion in this c hap -
ter. R (Reverse)
This p osition is for b ac king the vehic le.
To shift from the “N ” to “R ” p osition, first stop the vehic le c omp letely
then move the lever to the “R ” p osition.

Starting and operating7-19
–
CONTINUED –

Similarly, in order to prevent over-revving during deceleration
of the vehicle, the transmission will remain in the current gear if the speed of the vehicle is in excess of the Maximum AllowableSpeed for the gear to which the selector lever has been moved. Driving tips
Always ap p ly the foot or p arking b rake when the veh ic le is
stop p ed in the “D ”, “3 ”, “2 ”, “1 ” or “R ” p osition.
Always set the p arking b rake when p arking your vehi c le. Do not
hold the vehic le with only the transmission. Do not keep the vehic le in a stationary p osition on an up hill g rad e
b y using the “D ”, “3 ”, “2 ”, or “1 ” p osition. Use the b rake instead .
Shift lock release
If the selec tor lever d oes not move from the “P ” p osition with the b rake
p ed al d ep ressed and the ig nition switc h in the “ON ” p osition, p erform
the following step s:
To overrid e the shift loc k:
1. Set the p arking b rake and stop the eng ine.
2. Take out the sc rewd river from the tool b ag .
3. Remove the c over b y p rying on the ed g e with the r eg ular sc rewd river.
HB7020BA
HB7010CA
4. Insert the sc rewd river into the hole.
5. Push d own on the sc rewd river and move the selec to r lever from the
“ P ” to the “N ” p osition.
6. Remove the sc rewd river from the hole. Dep ress the b rake p ed al and

7-20start the eng ine.
Take your vehic le to the nearest SUBARU d ealer imme
d iately to have the
system rep aired . Rear viscous limited slip differential (LSD)
(GT, GT-LTD, OUTBACK-CW and OUTBACK-LTD)
CAUTION
Never start the engine while a tire on one side is jacked up, as
the vehicle may move. If one rear tire is spinning in mud, avoid continued spinning at
high speed as this could adversely affect the LSD. If a different size rear tire is temporarily used (as in an emer-
gency), it will adversely affect the LSD. Always replace it with aregular size tire as soon as possible.
The LSD p rovid es op timum d istrib ution of p ower ac c o rd ing to the d iffer-
enc e in revolutions b etween the rig ht and left rear wheels that may b e
c aused b y c ertain d riving c ond itions, thereb y imp ro ving d riving stab ility
on snow-c overed , mud d y or other slip p ery road s. Power steering
CAUTION
Do not hold the steering wheel at the fully locked position left or right for more than five seconds. This may damage the powersteering pump.
The p ower steering system op erates only when the en g ine is running .
If you lose p ower steering assist b ec ause the eng in e stop s or the system
fails to func tion, you c an steer b ut it will take m uc h more effort.

Starting and operating7-21
–
CONTINUED –
Braking
Braking tips
WARNING
Never rest your foot on the brake pedal while driving. This can
cause dangerous overheating of the brakes and needless wearon the brake pads and linings.
When the brakes get wet
When d riving in rain or after washing the vehic le, the b rakes may g et
wet. As a result, b rake stop p ing d istanc e will b e l ong er. To d ry the
b rakes, d rive the vehic le at a safe sp eed while lig htly d ep ressing the
b rake p ed al to heat up the b rakes. Use of engine braking
Rememb er to make use of eng ine b raking in ad d ition to foot b raking .
When d esc end ing a g rad e, if only the foot b rake is used , the b rakes
may start working imp rop erly b ec ause of b rake fluid overheating ,
c aused b y overheated b rake p ad s. To help p revent th is, shift into a
lower g ear to g et strong er eng ine b raking . Braking when a tire is punctured
Do not d ep ress the b rake p ed al sud d enly when a tire is p unc tured .
This c ould c ause a loss of c ontrol of the vehic le. Keep d riving straig ht
ahead while g rad ually red uc ing sp eed . Then slowly p ull off the road
to a safe p lac e.
Brake system Two separate circuits
Your vehic le has two sep arate c irc uit b rake systems . Eac h c irc uit
works d iag onally ac ross the vehic le. If one c irc uit of the b rake system
should fail, the other half of the system still wor ks. If one c irc uit fails,
the b rake p ed al will g o d own muc h c loser to the flo or than usual and
you will need to p ress it d own muc h hard er. And a m uc h long er d is-
tanc e will b e need ed to stop the vehic le.

Starting and operating7-23
–
CONTINUED –
ABS (Anti-lock Brake System)
WARNING
Always use the utmost care in driving – overconfidence because
you are driving with an ABS equipped vehicle could easily lead to a serious accident.
CAUTION
The ABS system does not always decrease stopping distance.
You should always maintain a safe following distance from othervehicles. When driving on badly surfaced roads, gravel roads, icy road,
or over deep newly fallen snow, stopping distances may be long-er for a vehicle with the ABS system than one without. When driv-ing under these conditions, therefore, reduce your speed and
leave ample distance from other vehicles. When you feel the ABS system operating, you should maintain
constant brake pedal pressure. Do not pump the brake pedal
since doing so may defeat the operation of the ABS system.
The ABS system p revents the loc k-up of wheels whic h may oc c ur d uring
sud d en b raking or b raking on slip p ery road surfac es . This help s p revent
the loss of steering c ontrol and d irec tional stab il ity c aused b y wheel
loc k-up .
When the ABS system is op erating , you may hear a c h attering noise or
feel a slig ht vib ration in the b rake p ed al. This is normal when the ABS
op erates.
The ABS system will not op erate when the vehic le sp eed is b elow
ap p roximately 6 mp h (10 km/h).
ABS system self-check
You may feel a slig ht shoc k in the b rake p ed al and hear the op erating
sound of ABS from the eng ine c omp artment just after the vehic le is

Starting and operating7-25
–
CONTINUED –
but goes out immediately, remaining off.
The warning light remains on after the engine has been
started, but it goes out when the vehicle speed reaches about 8mph (12 km/h). The warning light comes on during driving, but it goes out
immediately and remains off.
When d riving with an insuffic ient b attery voltag e s uc h as when the en-
g ine is jump started , the ABS warning lig ht may c om e on. This is d ue
to the low b attery voltag e and d oes not ind ic ate a malfunc tion. When
the b attery b ec omes fully c harg ed , the lig ht will g o out.
Parking your vehicle
WARNING
Never leave unattended children or pets in the vehicle. They
could accidentally injure themselves or others through inadver- tent operation of the vehicle. Also, on hot or sunny days, the tem-perature in a closed vehicle could quickly become high enoughto cause severe or possibly fatal injuries to them. Do not park the vehicle over flammable materials such as dry
grass, waste paper or rags, as they may burn easily if they comenear hot engine or exhaust system parts. Be sure to stop the engine if you take a nap in the vehicle. If
engine exhaust gas enters the passenger compartment, occu-pants in the vehicle could die from carbon monoxide (CO) con-tained in the exhaust gas.
CAUTION
Never drive while the parking brake is set because this will cause
unnecessary wear on the brake linings. Before starting to drive,always make sure that the parking brake has been fully released.
To set the p arking b rake, p ress the b rake p ed al fir mly and hold it d own

Driving tips8-13
–
CONTINUED –
n
Wiper operation when snowing
Before d riving in c old weather, make sure the wip er b lad es are not
frozen to the wind shield or rear wind ow. If the wip er b lad es are frozen
to the wind shield or rear wind ow, use the d efroster with the airflow
c ontrol d ial in the “
” p osition and the temp erature c ontrol d ial set
for maximum warmth until the wip er b lad es are c omp l etely thawed
out. If your vehic le is eq uip p ed with a wip er d eic e r, it is help ful to thaw
the wind shield wip er b lad es. To thaw out the rear w ip er b lad e, use the
rear wind ow d efog g er.
When d riving in snow, if frozen snow starts to stic k on the surfac e of
the wind shield d esp ite wip er op eration, use the d ef roster with the air-
flow c ontrol d ial in “
” and the temp erature c ontrol d ial set for max-
imum warmth. After the wind shield g ets warmed enoug h to melt the
frozen snow on it, wash it away using the wind shiel d washer.
Snow stuc k on the wip er arm p revents the wip er from working effec -
tively. If snow is stuc k on the wip er arm, p ull off the road to a safe
p lac e, then remove it. If you stop the c ar at road sid e, use the hazard
warning flasher to alert other d rivers.
We rec ommend use of non-freezing typ e wip er b lad es d uring the sea-
sons you c ould have snow and sub -zero temp eratures. Corrosion protection
Refer to the “Corrosion p rotec tion ” sec tion (c hap ter 10).
Snow tires
WARNING
When replacing a tire, make sure you use only the same size,
circumferences, construction, brand, and load range as the origi- nal tires listed on the tire placard. Using other sizes, circumfer-
ences or construction may result in severe mechanical damageto the drive train of your vehicle and may affect ride, handling,braking, speedometer/odometer calibration, and clearancebetween the body and tires. It also may be dangerous and lead toloss of vehicle control.

Driving tips8-15
–
CONTINUED –

Rocking the vehicle
If you must roc k the vehic le to free it from snow, sand , or mud , d ep ress
the ac c elerator p ed al slig htly and move the selec to r lever b ac k and forth
b etween “D ” and “R ” rep eated ly. Do not rac e the eng ine. For the b est
p ossib le trac tion, avoid sp inning the wheels when t rying to free the ve-
hic le.
When the road surfac e is extremely slip p ery, you c a n ob tain b etter trac -
tion b y starting the vehic le with the transmission in 2nd than 1st (b oth for
MT and AT).
Refer to the “Automatic transmission ” sec tion in c hap ter 7 for information
on hold ing the transmission in 2nd p osition.
Loading your vehicle
WARNING
Never allow passengers to ride on the folded rear seatback, in
the trunk or in the cargo area. Doing so may result in serious in-
jury. Never stack luggage or other cargo higher than the top of the
seatback because it could tumble forward and injure passengersin the event of a sudden stop or accident. Keep luggage or cargo
low, as close to the floor as possible. When you carry something inside the vehicle, secure it when-
ever you can to prevent it from being thrown around inside the
vehicle during sudden stops, sharp turns or in an accident. Do not pile heavy loads on the roof. These loads raise the
vehicle’ s center of gravity and make it more prone to tip over.
Secure skis and other lengthy items properly to prevent them
from shooting forward and causing serious injury during a sud-den stop. Never exceed the maximum load limit. If you do, some parts on
your vehicle can break, or it can change the way your vehicle
handles. This could result in loss of control and cause personal

Driving tips8-19
–
CONTINUED –
ing attac hment, never exc eed the maximum load limit
exp lained b elow.
You should also b e c areful that your vehic le d oes n ot exc eed the Gross
Vehic le Weig ht Rating (GVWR) and front and rear Gro ss Axle Weig ht Rat-
ing (GAWR). See the “Load ing your vehic le ” sec tion in this c hap ter for
information on load ing c arg o into or onto your vehi c le. The maximum
load limit of the c arg o, c rossb ars and c arrying att ac hment must not ex-
c eed 100 lb . (45 kg ). Plac e the heaviest load at th e b ottom, nearest the
roof, and evenly d istrib ute the c arg o. Always p rop e rly sec ure all c arg o.
Installing carrying attachments on the crossbars
When installing any c arrying attac hment suc h as a b ike c arrier, ski
c arrier, kayak c arrier, c arg o b asket, etc . on the c rossb ars, follow the
manufac turer ’s instruc tions and make sure that the attac hment is se-
c urely fixed to the c rossb ars. Use only attac hments d esig ned sp ec ifi-
c ally for the c rossb ars. A set of the c rossb ars is d esig ned to c arry
load s (c arg o and attac hment) of not more than 100 lb. (45 kg). Before
op erating the vehic le, make sure that the c arg o is p rop erly sec ured
on the attac hment. NOTE Remember that the vehicle ’s center of gravity is altered with the
weight of the load on the roof, thus affecting the driving charac- teristics.
Drive carefully. Avoid rapid starts, hard cornering and abruptstops. Crosswind effects will be increased. Removal and installation of the crossbars CAUTION
Do not carry cargo on the roof when the crossbars are removed. Luggage on the roof will be thrown forward or backward in sud-den stops or rapid accelerations, resulting in a dangerous roadhazard.
The c rossb ars c an b e removed when you d o not use th e roof to c arry
c arg o.

Driving tips8-35
–
CONTINUED –

Trailer towing tips CAUTION
Never exceed 45 mph (72 km/h) when towing a trailer in hilly
country on hot days. When towing a trailer, steering, stability, stopping distance and
braking performance will be different from normal operation. For
safety’ s sake, you should employ extra caution when towing a
trailer and you should never speed. You should also keep the fol-lowing tips in mind:
n Before starting out on a trip
Chec k that the vehic le and vehic le-to-hitc h mountin g are in g ood
c ond ition. If any p rob lems are ap p arent, d o not tow the trailer.
Chec k that the vehic le sits horizontally with the t railer attac hed . If
the vehic le is tip p ed sharp ly up at the front and d own at the rear,
c hec k the total trailer weig ht, GVW, GAWs and tong u e load ag ain,
then c onfirm that the load and its d istrib ution are ac c ep tab le.
Chec k that the tire p ressures are c orrec t.
Chec k that the vehic le and trailer are c onnec ted p r op erly. Confirm
that. –the trailer tong ue is c onnec ted p rop erly to the hit c h b all.
– the trailer lig hts c onnec tor is c onnec ted p rop erly and trailer’s
b rake lig hts illuminate when the vehic le ’s b rake p ed al is p ressed ,
and that the trailer ’s turn sig nal lig hts flash when the vehic le ’s turn
sig nal lever is op erated .
– the safety c hains are c onnec ted p rop erly.
– all c arg o in the trailer is sec ured safety in p osit ion.
– the sid e mirrors p rovid e a g ood rearward field of v iew without a
sig nific ant b lind sp ot.
Suffic ient time should b e taken to learn the “feel ” of the vehic le/
trailer c omb ination b efore starting out on a trip . In an area free of traf-
fic , p rac tic e turning , stop p ing and b ac king up .