radio SUBARU OUTBACK 2000 3.G Owners Manual

1-70airbags)
Replacement of seat fabric or leather (only for vehicles with
SRS side airbags) Installation of additional fabric or leather on the front seat
(only for vehicles with SRS side airbags)
Installation of additional electrical/electronic equipment such
as a mobile two-way radio on or near the SRS airbag system
components and/or wiring is not advisable. This could interferewith proper operation of the SRS airbag system.
CAUTION
Do not perform any of the following modifications. Such modifi-cations can interfere with proper operation of the SRS airbag sys-tem. Attachment of any equipment (brush bar, winches, snow plow,
skid plate, etc.) other than SUBARU genuine accessory parts tothe front end. Modification of the suspension system or front end structure.
Installation of a tire of different size and construction from the
original tires listed on the tire placard attached to the door jamb. Attachment of any equipment (side steps or side sill protec-
tors, etc.) other than SUBARU genuine accessory parts to theside body (only for vehicles with side airbags).
Always c onsult your SUBARU d ealer if you want to in stall any ac c essory
p arts to your vehic le.

Audio5-7
–
CONTINUED –
Type P119 and P120 audio set (if equipped)
* The aud io typ e c od e numb er is found on the lid of
the c assette slot.
Typ e P119: Without weather b and
Typ e P120: With weather b and
The aud io set will op erate only when the ig nition s witc h is in the “ACC ” or
“ ON ” p osition.
Radio operation
HB5041BB
1 Power switc h/Volume, Tone,
Balanc e, Fad er c ontrol d ial
2 AUDIO b utton
3 BAND b utton 4
Tuning b uttons
5 Preset b uttons
6 SCAN b utton
Power switch and volume/bass/treble/fader/balance control
n Power switch and volume control (PWR/VOL)
The d ial 1 is used for b oth p ower (ON/OFF) and volume c ontrol . The
rad io is turned ON and OFF b y p ushing the d ial and the volume is
c ontrolled b y turning the d ial.

5-10Press the
“SCAN ” b utton ag ain to c anc el the SCAN mod e and to stop
on any d isp layed freq uenc y.
When the “SCAN ” b utton is p ressed for automatic tuning , stations a re
sc anned in the d irec tion of low freq uenc ies to hig h freq uenc ies only.
Automatic tuning may not func tion p rop erly if the s tation rec ep tion is
weakened b y d istanc e from the station or p roximity to tall b uild ing s
and hills. Selecting preset stations
Presetting a station with a “p reset b utton ”
5 allows you to selec t that
station in a sing le op eration. Up to six WB (if eq u ip p ed ), AM, FM1 and
FM2 stations eac h may b e p reset. How to preset stations
1. Press the “BAND ” b utton 3 to selec t FM1, FM2, AM or WB (if
eq uip p ed ) rec ep tion.
2. Press the “SCAN ” b utton or tune the rad io manually until the
d esired station freq uenc y is d isp layed .
3. Press one of the p reset b uttons for more than 2 s ec ond s to store
the freq uenc y. At this time, there will momentarily b e no sound from
the rad io. If the b utton is p ressed for less than 2 sec ond s, the p rec ed -
ing selec tion will remain in memory.
NOTE If the connection between the radio and battery is broken for any
reason such as vehicle maintenance or radio removal, all stationsstored in the preset buttons are cleared. If this occurs, it is neces-sary to reset the preset buttons.

5-14After insertion, the CD p layer mod e ind ic ator
“CD ” will c ome on and
p layb ac k will start. n When CD is in the CD player
Press the “CD ” b utton
U. The “CD ” ind ic ator will c ome on, and the
trac k numb er will ap p ear on the d isp lay and the CD p layer will start
p layb ac k. NOTE If the “CD” button is pressed during a radio broadcast, the
disc will interrupt the broadcast. After playback on the last song finishes, the player will auto-
matically return to track 1 (the first song on the disc). To select a song from its beginning
Briefly p ress the “ ❚” b utton
P to skip to the b eg inning of the next
trac k and b riefly p ress the “❚ ” b utton to skip to the b eg inning of
the c urrent trac k. Fast-forwarding and fast-reverse
Press the “ ❚” b utton
P c ontinuously for more than a half sec ond
to fast-forward the d isc .
Press the “❚ ” b utton c ontinuously for more than a half sec ond to
fast reverse the d isc .
Release the b utton to stop fast forward ing or fast reverse.
Repeat
Press the “RPT ” b utton
O while a song is p laying to p lay the song
rep eated ly. The “RPT ” ind ic ator will c ome on and the song will b e
p layed c ontinuously. To c anc el the rep eat mod e, p re ss the b utton
ag ain. Then the “RPT ” ind ic ator g oes out, and normal p layb ac k mod e
is restored . Random playback
Press the “RAND ” b utton
I while a d isc is b eing p layed b ac k to p lay
all song s on the d isc in a rand om ord er. The “RAND ” ind ic ator will
c ome on and all song s on the d isc will b e p layed in a rand om ord er.
To c anc el the rand om mod e, p ress the b utton ag ain. Then the
“ RAND ” ind ic ator g oes out, and normal p layb ac k mod e is re stored .

5-16CD changer control (If optional in dash CD changer is connected)
An op tional CD c hang er c an b e c onnec ted to this aud
io unit. See your
SUBARU d ealer for more information. For p roc ed ures for load ing and un-
load ing CDs, refer to “In-d ash 6 CD auto c hang er ” in this c hap ter.
HB5041EB
S CD b utton
D Disc up /d own b uttons
F RAND (Rand om) b utton G
RPT (Rep eat) b utton
H Trac k selec tion b uttons
J SCAN b utton
To start playback
Press the “CD ” b utton S. The “CD ” ind ic ator will c ome on and the
d isc numb er will ap p ear on the d isp lay and the CD c hang er will start
p layb ac k. NOTE If the “CD” button is pressed during a radio broadcast, the CD
changer will interrupt the broadcast. At the end of the disc, playback automatically continues with
the next disc. After playback on the last disc finishes, the player will auto-
matically return to the first disc.

Audio5-19
–
CONTINUED –
Type P121 audio set (if equipped)
* The aud io typ e c od e numb er is found on the lid of
the c assette slot.
The rad io will op erate only when the ig nition switc h is in the “ACC ” or
“ ON ” p osition.
Radio operation
HB5042BB
1 FM/AM selec tion b utton
2 SCAN b utton
3 WB (weather b and ) b utton
4 Tuning b uttons
5 Preset b uttons 6
Fad er/Balanc e selec tion
b utton
7 Power switc h, Volume c ontrol,
Bass/Mid d le/Treb le c ontrol and
Fad er/Balanc e c ontrol d ial
8 AUDIO (aud io mod e) b utton
Power switch and volume/bass/treble/fader/balance control (PWR/VOL)
The d ial 7 is used for b oth p ower (ON/OFF) and volume c ontrol . The
rad io is turned ON and OFF b y p ushing the d ial and the volume is
c ontrolled b y turning the d ial.

Audio5-23
–
CONTINUED –
Automatic tuning may not func tion p rop erly if the s
tation rec ep tion is
weakened b y d istanc e from the station or p roximity to tall b uild ing s and
hills. Selecting preset stations
Presetting a station with a p reset b utton 5 allows you to selec t that
station in a sing le op eration. Up to six AM, FM1, F M2 and WB stations
eac h may b e p reset. How to preset stations
1. Press the “FM/AM ” selec tion b utton to selec t AM, FM1 or FM2 re-
c ep tion.
OR
Press the “WB ” b utton
3 to selec t the weather b and .
2. Press the “SCAN ” b utton 2 or tune the rad io manually until the d e-
sired station freq uenc y is d isp layed .
3. Press one of the p reset b uttons 5 for at least 1.5 seconds to store
the freq uenc y. The freq uenc y of the station will fl ash onc e on the d is-
p lay at this time. If the b utton is p ressed for les s than 1.5 sec ond s, the
p rec ed ing selec tion will remain in memory. NOTE If the connection between the radio and battery is broken for any
reason such as vehicle maintenance or radio removal, all stationsstored in the preset buttons are cleared. If this occurs, it is neces-sary to reset the preset buttons.

Audio5-33
–
CONTINUED –
Type C117 audio set (if equipped)
* The aud io typ e c od e numb er is found on the lid of
the c assette slot.
The aud io set will op erate only when the ig nition s witc h is in the “ACC ” or
“ ON ” p ositions.
Radio operation
HB5043BB
1 Tuning b uttons
2 SCAN b utton
3 FM/AM selec tion b utton
4 Preset b uttons 5
AUDIO b utton
6 Power switc h and volume
c ontrol
Power switch and volume/bass/treble/fader/balance control
n Power switch and volume control (PWR/VOL)
The d ial 6 is used for b oth p ower (on/off) and volume c ontrol . The
rad io is turned on and off b y p ushing the d ial and the volume is c on-
trolled b y turning the d ial. Tone and balance control
The volume c ontrol d ial 6 normally func tions as a volume c ontrol.
This d ial b ec omes a c ontrol for Bass, Treb le, Fad er or Balanc e when
you selec t the ap p rop riate tone and b alanc e c ontrol mod e.

5-36
Selecting preset stations
Presetting a station with a p reset b utton 4 allows you to selec t that
station in a sing le op eration. Up to six AM, FM1 an d FM2 stations
eac h may b e p reset. How to preset stations
1. Press the “FM/AM ” selec tion b utton
3 to selec t FM1, FM2 or AM
rec ep tion.
2. Press the “SCAN ” b utton 2 or tune the rad io manually until the d e-
sired station freq uenc y is d isp layed .
3. Press one of the p reset b uttons 4 for at least two seconds to
store the freq uenc y. The freq uenc y of the station w ill flash onc e on the
d isp lay at this time. If the b utton is p ressed for less than two sec ond s,
the p rec ed ing selec tion will remain in memory.
NOTE If the connection between the radio and battery is broken for any
reason such as vehicle maintenance or radio removal, all stationsstored in the preset buttons are cleared. If this occurs, it is neces-sary to reset the preset buttons.