sensor SUBARU OUTBACK 2001 3.G User Guide

Instruments and controls3-33
–
CONTINUED –
n
Photosensors
HB6020BA
The mirror has a p hotosensor attac hed on b oth the f ront and b ac k
sid es. If the g lare from the head lig hts of vehic les b ehind you strikes
the mirror, these sensors d etec t it and make the re flec tion surfac e of
the mirror d immer to help p revent you from b eing b l ind ed . For this
reason, use c are not to c over the sensors with stic kers, or other simi-
lar items. Period ic ally wip e the sensors c lean usin g a p iec e of d ry soft
c otton c loth or an ap p lic ator. n Compass calibration
1. For op timum c alib ration, switc h off all nonessent ial elec tric al ac -
c essories (rear wind ow d efog g er, heater/air c ond iti oning system,
sp otlig ht, etc .) and ensure all d oors are shut.
2. Drive to an op en, level area away from larg e meta llic ob jec ts or
struc tures and make c ertain the ig nition switc h is in the “ON ” p osition.
3. Press and hold the left b utton for 3 sec ond s then release, and the
c omp ass will enter the c alib ration mod e. “CAL ” and d irec tion will b e
d isp layed .
4. Drive slowly in a c irc le until “CAL ” d isap p ears from the d isp lay
(ab out two or three c irc les).
5. The c omp ass is now c alib rated . Further c alib ratio n is not req uired .
The c omp ass will automatic ally c alib rate from this p oint forward .

4-12
Control panel
HB5017BC
1. AUTO switc h
2. OFF switc h
3. Outsid e air temp erature switc h
4. Defroster switc h
5. Rear wind ow d efog g er switc h (Refer to the “Rear wind ow d efog -
g er ” in c hap ter 3.)
6. Fan sp eed c ontrol switc h
7. Air c ond itioner switc h
8. Air flow c ontrol switc h
9. Air inlet selec tion switc h
10. Temp erature c ontrol d ial
11. In-vehic le temp erature sensor. n AUTO switch
AUTO mode operation:
The Automatic Climate Control system automatic ally c ontrols the air
temp erature of the p asseng er c omp artment in the AUT O mod e. When
the “AUTO ” switc h is p ressed , the ind ic ator lig ht “AUTO ” on the c on-
trol p anel c omes on. In this state, outlet air temp erature, fan sp eed , air
flow d istrib ution, air-inlet c ontrol, and air c ond i tioner c omp ressor op -
eration are automatic ally c ontrolled . ECON (economy) mode:
When you p ress the “AUTO ” switc h while the system is in the AUTO
mod e, it selec ts the ECON (ec onomy) mod e, turning o n the

4-18
Temperature sensors
This Automatic Climate Control system emp loys the s everal sensors.
These are very d elic ate p arts. Therefore, if these sensors are d am-
ag ed , it is p ossib le that the Automatic Climate Con trol system will not
p rop erly c ontrol the air temp erature in the p asseng er c omp artment.
To p revent p ossib le d amag e to the sensors, p lease o b serve the fol-
lowing :
–Do not allow anything to imp ac t the sensors.
– Be c areful not to let water c ontac t the sensors.
– Do not c over the sensors.
The sensors are found at the following loc ations: – Sun-load sensor (b esid e the wind shield d efroster g r ille)
– In-vehic le temp erature sensor (b esid e the temp eratu re c ontrol
d ial.)
– Amb ient sensor (at the b ac ksid e of the front g rille )
HB5025BB
HB5024BB

Audio5-25
–
CONTINUED –
n
When cassette tape is in the player
When the “TAPE ” b utton 9 is p ressed , the d isp lay will show “PLAY ”
and the p layer will start p layb ac k. Tape travel indicators
These ind ic ate the d irec tion the c assette tap e is m oving .
: ind ic ates that the top sid e of the c assette is b eing p layed b ac k.
: ind ic ates that the b ottom sid e of the c assette i s b eing p layed
b ac k. Program switching button (PROG)
When the p rog ram switc hing b utton “PROG ”
I is p ressed d uring
p layb ac k, the tap e travel ind ic ators will switc h an d the p layer will b e-
g in p laying b ac k the op p osite sid e of the tap e. The same mec hanism
is automatic ally ac tivated when the end of the tap e is reac hed . This
allows the op p osite sid e of the tap e to p lay, p rovi d ing c ontinuous
p layb ac k. Fast-forward button (FF)
To fast-forward the tap e, p ress the “FF ” b utton
T. The d isp lay will
show “FF ”. To stop fast-forward ing , p ress the “FF ” or “TAPE ” 9 b utton.
Rewind button (REW)
To rewind the tap e, p ress the “REW ” b utton Y. The d isp lay will ind i-
c ate “REW ”. To stop rewind ing , p ress the “REW ” or “TAPE ” 9 b utton.
Eject button (
)
When “
” b utton W is p ressed , p lay b ac k stop s and the c assette
tap e is ejec ted .
The ejec tion func tion also op erates when the ig niti on switc h is in the
“ LOCK ” p osition. Always make c ertain that you remove the c assette
tap e. Tape program sensor button (TPS)
n Blank skip
When the “TPS ” b utton
E is p ressed , the “TPS ” ind ic ator will c ome on
and the p layer will automatic ally skip any b lank p o rtion of 15 sec ond
or more and p lay the next p rog ram, even if it is on the other sid e. To
c anc el b lank skip mod e, p ress the “TPS ” b utton ag ain.

Audio5-27
–
CONTINUED –
* Noise red uc tion system manufac tured und er lic ense
from Dolb y Lab oratories
Lic ensing Corp oration. “Dolb y ” and the d oub le-D Symb ol are trad e marks of
Dolb y Lab oratories Lic ensing Corp oration.
Auto metal sensor
The c assette p layer automatic ally ad justs for metal or CrO
2 tap e.
Compact disc player operation
HB5042DB
O SCAN b utton
P Disc slot
A Ejec t b utton
S Rand om b utton D
Rep eat b utton
F Trac k selec tion b uttons
G CD (CD p layer selec tion)
b utton
To play back a compact disc
n When CD is not in the player
Hold a d isc with a fing er in the c enter hole while g rip p ing the ed g e of
the d isc , then insert it in to the slot (with the l ab el sid e up ) and the
p layer will automatic ally p ull the d isc into p ositi on.
A sing le CD (8 c m/3 inc h CD) may also b e used witho ut any ad ap ter.