clock SUBARU OUTBACK 2003 3.G User Guide

5-34
Selecting a desired track (TRACK)
HB5065BA
nSkipping forward
Turn the FF ·FB dial T clockwise and release it immediately to skip to
the beginning of the next track. Each time the knob is turned and re-
leased, the indicated track number will increase. n Skipping backward
Turn the FF ·FB dial
T counterclockwise and release it immediately to
skip to the beginning of the current track. If you continue to turn and
release the knob, the indicated truck number will decrease. n Fast forwarding
Turn the FF ·FB dial T clockwise and hold it continuously for more than
0.5 second to fast forward the disc.
Release the knob to stop fast forwarding. n Fast reversing
Turn the FF ·FB dial T counterclockwise and hold it continuously for
more than 0.5 second to fast reverse the disc.
Release the knob to stop fast reverse. Repeat playback
Press the “RPT” button R while a song is playing to play the song
repeatedly. The “RPT” indicator will come on and the song will be
played continuously. To cancel the repeat mode, press the button
again. Then the “RPT” indicator goes out, and normal playback mode
is restored.
❚: Skipping forward
❚ : Skipping backward
: Fast forwarding
: Fast reversing

6-6

Glove box
HS0090
Unlock
Lock
To open the glove box, pull the handle. To close it, push the lid firmly
upward.
To lock the glove box, insert the key and turn it clockwise. Center console
HB6022BA
To open the lid, pull up the lock release.
If the console lid is fully opened when a large cup is put in the rear pas-
senger’ s cup holder, the lid may hit the cup and beverage may be
spilled.

7-6
HB7030BB
2. Remove the fuel filler cap by turning it slowly counterclockwise.
3. Stop filling the tank after the fuel filler pump automatically clicks off.
Do not add any more fuel.
4. Put the cap back on, turn it clockwise until you hear a clicking
noise. Be certain not to catch the tether under the cap while tighten-ing.
5. Close the fuel filler lid completely.
If you spill any fuel on the painted surface, rinse it off immediately.
Otherwise, the painted surface could be damaged. NOTE
HG3016AA
You will see the “FUEL DOOR p” sign in the combination
meter. This indicates that the fuel filler door (lid) is located on the right side of the vehicle.

9-6
5. Take out the spare tire, jack, and wheel nut wrench.
HB6008BCHB9003BB
HS0252
Temporary spare tire
HBF015CB
Jack handle
Jack
Spare tireHB8004BD
The spare tire is stored under the floor of the trunk or cargo area.
To remove the spare tire, proceed as follows:Sedan: Remove the floor cover from the trunk. Remove the storage tray.
Turn the attaching bolt counterclockwise, then take the spare tire out.Station wagon: Open the lid and hang the hook provided on the under-

9
In case of emergency9-7
–
CONTINUED –
side of the lid on the rear edge of the roof to keep the lid open.
Remove the storage tray. Turn the attaching bolt counterclockwise, then
take spare tire out.
If the spare tire provided in your vehicle is a temporary spare tire, care-
fully read the section
“Temporary spare tire ” in this chapter and strictly
follow the instructions.
HB7008CD
HB9001BB
The jack is stored on the left side of the trunk or cargo area.
To take out the jack:
Remove the cover, turn the jackscrew counterclockwise to loosen it, then
remove the jack.
HB9041BA
HB9040BA
If the jackscrew is too tight to be loosened by hand, loosen it using a
screwdriver or the jack handle.

9-10
HG0104
OM-H0172
12. Put on the spare tire. Replace the wheel nuts. Tighten them by hand.
13. Turn the jack handle counterclockwise to lower the vehicle.
14. Use the wheel nut wrench to securely tighten the wheel nuts to the
specified torque, following the tightening order in the illustration.
OM-H0377
The torque for tightening the nuts is 58 to 72 ft-lb (78 to 98 N-m, 8 to 10
kg-m). This torque is equivalent to applying about 88 to 110 lbs (40 to 50
kg) at the top of the wheel nut wrench. Never use your foot on the wheel
nut wrench or a pipe extension on the wrench because you may exceed
the specified torque. Have the wheel nut torque checked at the nearest
automotive service facility.
15. Store the flat tire in the spare tire compartment.

9
In case of emergency9-11
–
CONTINUED –
HS0153
Flat tire Attaching bolt
Spacer
When storing a conventional tire, put the spacer upside down and tight-
en the attaching bolt firmly.
Also store the jack and wheel nut wrench in their storage locations.
HB9041CA
HB9040CA
After placing the jack in its storage location, turn the jackscrew clock-
wise by hand until it becomes too hard to turn. Then, tighten it by an
additional 1/4 – 1/3 of a turn using a screwdriver or the jack handle. Un-
less the jack is properly secured, it may rattle while the vehicle is mov-ing.

9
In case of emergency9-15
–
CONTINUED –
Engine overheating
WARNING
Never attempt to remove the radiator cap until the engine has been shut off and has fully cooled down. When the engine is hot,the coolant is under pressure. Removing the cap while the engineis still hot could release a spray of boiling hot coolant, which
could burn you very seriously.
If the engine overheats, safely pull off the road and stop the vehicle in asafe place. If steam is coming from the engine compartment
Turn the engine off and get everyone away from the vehicle until itcools down. If no steam is coming from the engine compartment
1. Keep the engine running at idling speed.
2. Open the hood to ventilate the engine compartment.
Confirm that the cooling fan is turning. If the fan is not turning, im-
mediately turn the engine off and contact your authorized dealer for
repair.
3. After the engine coolant temperature has dropped, turn off the en-gine.
If the temperature gauge stays at the overheated zone, turn the en-
gine off.
4. After the engine has fully cooled down, check the coolant level in
the reserve tank.If the coolant level is below the “MIN” mark, add coolant up to the
“MAX” mark.
5. If there is no coolant in the reserve tank, add coolant to the reserve
tank. Then remove the radiator cap and fill the radiator with coolant.
If you remove the radiator cap from a hot radiator, first wrap a thick
cloth around the radiator cap, then turn the cap counterclockwise
slowly without pressing down until it stops. Release the pressure from

9-20
HB9044AA
3. Turn the towing hook cover clockwise, pivoting it about the side
that is next to the fog lamp. Pull out the towing hook cover to removeit. nTowing hook cover installation procedure
For except OUTBACK models:
HB9052BA
Align the towing hook cover with its original installation position and
press all parts of it into place.

9-24Moonroof —
if the moonroof cannot be closed
If the moonroof cannot be closed with the moonroof switch, you can
close the moonroof manually. Sedan
1. Take out the hex-headed wrench from the glove box and screw-
driver from the tool bag.
HB9007BB
HB9006BA
2. Remove the map light lens by prying the edge of the lens with a
regular screwdriver, then remove the switch body retaining screws
and take off the moonroof switch.
HB9008BA
3. Insert the wrench in the end of the motor shaft.
To lower the moonroof, turn the wrench clockwise.
To close the moonroof, turn the wrench counterclockwise.
Have your vehicle checked by an authorized SUBARU dealer.