lights SUBARU OUTBACK 2003 3.G Owner's Manual

3
Instruments and controls3-29
–
CONTINUED –
Rear window defogger switch
CAUTION
Do not use sharp instruments or window cleaner containing
abrasives to clean the inner surface of the rear window. They may
damage the conductors printed on the window. To prevent the battery from being discharged, do not operate
the defogger continuously for any longer than necessary.
The rear window defogger operates only when the ignition switch is inthe “ON” position.
The rear window defogger switch is located on the climate control panel.
The defogger will automatically shut off after about 15 minutes. If the win-
dow clears before that time, push the switch to turn it off. It also turns off
when the ignition switch is turned to the “ACC” or “LOCK” position. If
defrosting or defogging is desired when you restart your vehicle, you
have to push the switch to turn it on again.
For vehicles with manual heating and air conditioning systems
HB5009BB
To turn on the defogger, push the switch. To turn it off, push the switch again.
The indicator light located on the switch lights up while the rear win-dow defogger is operating.

3-30
For vehicles with automatic climate control
HB3016BB
To turn on the defogger, push the switch. To turn it off, push the switch again.The indicator light “u ” lights up on the climate control display panel
while the rear window defogger is operating.
Windshield wiper deicer (if equipped)
CAUTION
To prevent the battery from being discharged, do not operate thewindshield wiper deicer continuously for any longer than neces-
sary.
HB2027BB

3
Instruments and controls3-31
–
CONTINUED –
The windshield wiper deicer operates only when the ignition switch is in the
“ON” position.
Before turning on the windshield wiper deicer, remove any snow from the
windshield. To turn on the windshield wiper deicer, push the switch. The
indicator light located on the switch lights up while the windshield wiper
deicer is operating.
The windshield wiper deicer will automatically shut off after about 15 min-
utes. If the wiper blades have been deiced completely before that time,
push the switch to turn it off. It also turns off when the ignition switch is
turned to the “ACC” or “LOCK” position. If deicing is not complete when
you restart your vehicle, you have to push the switch to turn the deiceron again. Mirrors
Always check that the inside and outside mirrors are properly adjusted
before you start driving. Inside mirror
HB4003BB
The inside mirror has a day and night position. Pull the tab at the bottom
of the mirror toward you for the night position. Push it away for the day
position. The night position reduces glare from headlights.

3-32
Auto-dimming mirror/compass (if equipped)
HB6019BB
The auto-dimming mirror/compass has an anti-glare feature which au-
tomatically reduces glare coming from headlights of vehicles behindyou. It also contains a built-in compass.By pressing and releasing the left button, the automatic dimming
function is toggled on or off. When the automatic dimming function is
on, the auto dimming indicator light (green) located to the right of the
button will illuminate. By pressing and releasing the right button, the compass display is
toggled on or off. When the compass is on, an illuminated compass
reading will appear in the lower part of the mirror.
Even with the mirror in anti-glare mode, the mirror surface turns bright
if the transmission is shifted into reverse. This is to ensure good rear-
ward visibility during reversing.

3
Instruments and controls3-33
–
CONTINUED –
n
Photosensors
HB6020BA
The mirror has a photosensor attached on both the front and back
sides. If the glare from the headlights of vehicles behind you strikes
the mirror, these sensors detect it and make the reflection surface of
the mirror dimmer to help prevent you from being blinded. For this
reason, use care not to cover the sensors with stickers, or other simi-
lar items. Periodically wipe the sensors clean using a piece of dry soft
cotton cloth or an applicator. nCompass calibration
1. For optimum calibration, switch off all nonessential electrical ac-
cessories (rear window defogger, heater/air conditioning system,
spotlight, etc.) and ensure all doors are shut.
2. Drive to an open, level area away from large metallic objects or
structures and make certain the ignition switch is in the “ON” position.
3. Press and hold the left button for 3 seconds then release, and thecompass will enter the calibration mode. “CAL” and direction will be
displayed.
4. Drive slowly in a circle until “CAL” disappears from the display
(about two or three circles).
5. The compass is now calibrated. Further calibration is not required.
The compass will automatically calibrate from this point forward.

4-14ECON (economy) mode:
When you press the
“AUTO” switch while the system is in the AUTO
mode, it selects the ECON (economy) mode, turning on the“
ECON ” indicator light. In the ECON mode, the compressor runs to
be thrifty with energy consumption. Interior windows tend to fog in this
energy-saving operation. It is therefore recommended that the AUTOmode be used only in high humidity conditions. Manual mode operation:
When the Automatic Climate Control system is operating in the AUTO
mode, pressing the “
”, “”, “MODE”, “A/C” or
“
” switch shifts the operation into the “MANUAL” mode and the
indicator light “AUTO” on the control panel will go out.
When the “
”, “”, “MODE”, “A/C” or “”
switch is pressed, the corresponding function can be controlled inde-
pendently, while automatic control of the other functions are main-tained.
To change the system back to the AUTO mode, press the “AUTO”
switch. n OFF switch
The Automatic Climate Control system turns off (the air conditioner
compressor and fan turn off) when the “OFF” switch is pressed.
When the “OFF” switch is pressed, the outside air introduction mode
(“
” position) is automatically selected.
NOTE Display illumination dimness cancellation (BRIGHT): Setting the light switch to the “p ” or “ a ” position causes the
illuminating icons on the display panel to dim. When travelingwith the lights on in gloomy daylight or in twilight, press the OFFswitch for 1 second or longer if you feel it is too hard to identify
the icons clearly. The brightness comes back to normal.If you wish to dim the icons again, hold down the OFF switchagain or if you can safely do so, turn the light switch OFF andthen place it in the “p ” or “a ” position.

5-22pear on display for a period of 15 seconds. Insert a disc during the period. The disc will be then automatically drawn in, and the playerwill begin to play back the first number of the disc.
To insert more discs in succession, repeat Steps 1 and 2. The
magazine will be loaded with discs in the ascending order of position
number.
If you do not insert any disc in 15 seconds after you have pressed the
“LOAD” button, the player will begin to play back the first number of
the last disc you have inserted. The disc indicator steadily lights up if a disc is already inserted in
the corresponding position of the magazine. While the player is in the loading mode, if you press the “FM/AM”
selection button 4, the player will enter the standby mode. Press the
“CD” button W to start playback.
n Inserting a disc in a desired position
1. Press the “LOAD” button. If the magazine in the player has an idle
position where you can insert a disc, the “DISC” indicator associated
with the idle position will blink.The positions in the magazine the indicator of which steadily lights up
are already loaded with discs.
2. Press the “DISC SELECT ” button
Y at the position where you want
to insert a disc. The associated “DISC” indicator will blink, and the
“IN” will be displayed.
3. If you insert a disc during the 15-second period while the “IN” is on
display, the disc will be automatically drawn in, and the player will
start playback of the disc, beginning with the first number. To insert more discs in succession, repeat Steps 1 and 2.
While the player is in the loading mode, if you press the “FM/AM”
selection button 4, the player will enter standby mode. Press the
“CD” button to start playback.
n Loading all the magazine (Full disc loading mode)
1. If you continue to press the “LOAD” button for more than 1.5 se-
conds, the player will produce beep sound and will enter the full disc
loading mode.
2. A “DISC” indicator will blink, and the “IN” will be on display for a

5
Audio5-23
–
CONTINUED –
period of 15 seconds. If a disc is successfully loaded during this peri- od, the
“DISC” indicator will stop blinking and will steadily light.
3. When the loading of a disc is complete, the next “DISC” indicator
will blink. Then repeat Step 2.
4. When the magazine is filled with discs by repeating Steps 2 and 3,
the player will start playback of the discs, beginning with the one in-
serted first.
If you fail to insert any disc during each 15-second interval, the full
disc loading mode will be canceled, and the player will start playback
of the disc inserted first. How to play back a CD or make a pause
n When there is no CD inserted:
Insert a CD by referring to “How to Insert a CD(s) ”.
When a CD is loaded, the player will start playback of the CD, begin-
ning with the first number. n When there are CDs loaded:
Press a desired one of the “DISC SELECT ” buttons
Y the “DISC” indi-
cator of which steadily lights up. The player will then start playback of
the selected CD, beginning with the first number. To select a song from its beginning
n Forward direction
Briefly press the “ ” button U to skip to the beginning of the next
track. Each time the button is pressed, the indicated track number will
increase. n Backward direction
Briefly press the “
 ” button U to skip to the beginning of the current
track. Each time the button is pressed, the indicated truck number will
decrease. Fast forwarding and fast reverse
n Fast forwarding
Press the “
 ” button U continuously for more than 0.5 second to fast
forward the disc.

5-32
How to insert a CD(s)
n Inserting a CD
1. Press “LOAD” button E. If the magazine in the player has an idle
position where you can insert a disc, the “DISC” indicator associated
with the idle position will blink.
If no indicator blinks, it means that there is no idle position in the mag-azine.
2. As soon as the “DISC” indicator begins to blink, the “CD-IN” will
appear on display for a period of 15 seconds. Insert a disc during theperiod. The disc will be then automatically drawn in, and the playerwill begin to play back the first number of the disc. To insert more discs in succession, repeat Steps 1 and 2. The
magazine will be loaded with discs in the ascending order of position
number.
If you do not insert any disc in 15 seconds after you have pressed the
“LOAD” button
E, the player will begin to play back the first number
of the last disc you have inserted. The disc indicator steadily lights up if a disc is already inserted in
the corresponding position of the magazine. While the player is in the loading mode, if you press “FM/AM”
selection button 1, the player will enter the standby mode. Press the
“Disc” button Y to start playback.
n Inserting a disc in a desired position
1. Press the “LOAD” button
E. If the magazine in the player has an
idle position where you can insert a disc, the “DISC” indicator
associated with the idle position will blink.The positions in the magazine the indicator of which steadily lights up
are already loaded with discs.
2. Press the “DISC SELECT ” button
U at the position where you want
to insert a disc. The associated “DISC” indicator will blink, and the
“CD-IN” will be displayed.
3. If you insert a disc during the 15-second period while the “IN” is on
display, the disc will be automatically drawn in, and the player will
start playback of the disc, beginning with the first number. To insert more discs in succession, repeat Steps 1 and 2.

5
Audio5-33
–
CONTINUED –

While the player is in the loading mode, if you press FM/AM selec-
tion button, the player will enter standby mode. Press the “DISC” but-
ton to start playback. n Loading all the magazine (Full disc loading mode)
1. If you continue to press the “LOAD” button
E for more than 1.5 se-
conds, the player will produce beep sound and will enter the full disc
loading mode.
2. A “DISC” indicator will blink, and the “CD-IN” will be on display for
a period of 15 seconds. If a disc is successfully loaded during thisperiod, the “DISC” indicator will stop blinking and will steadily light.
3. When the loading of a disc is complete, the next “DISC” indicator
will blink. Then repeat Step 2.
4. When the magazine is filled with discs by repeating Steps 2 and 3,
the player will start playback of the discs, beginning with the one in-
serted first.
If you fail to insert any disc during each 15-second interval, the full
disc loading mode will be canceled, and the player will start playback
of the disc inserted first. How to play back a CD or make a pause
n When there is no CD inserted:
Insert a CD by referring to “How to Insert a CD(s) ”.
When a CD is loaded, the player will start playback of the CD, begin-
ning with the first number. n When there are CDs loaded:
Press a desired one of the “DISC SELECT ” buttons
U the “DISC” indi-
cator of which steadily lights up. The player will then start playback of
the selected CD, beginning with the first number.