ad blue SUBARU OUTBACK 2016 6.G Navigation Manual

ROUTE GUIDANCE
232
No. Function
Select whether or not to use the expressway when
creating the route.
Select whether or not to use toll roads (Period Charge)
in the route.
Select whether or not to use toll roads (Per-use Toll) in
the route.
Select whether or not to use ferries when creating the
route. (However, ferries might not always be selected for
the route.) However, information on temporary service
ferries may not be displayed on the map. There may be
a fee for using the ferry.
Select whether or not to use Carpool/HOV lanes when
creating the route.
Select whether or not to use unpaved roads when
creating the route.
Select to search for the best green alternative route. If
this alternative route is much better than the selected
method, you can quickly switch to Green mode.

”The route is searched again, and the new
recommended route is indicated by a blue line.
SELECTING ROUTE TYPE
1. Display the “Route Settings (Route Settings)” screen.

:3
2. Select Route Planning Method (Route Planning
Method).
3. Select the desired route type.
No. Function
Select to search all roads for the quickest route following
the speed limits of the roads.
Select to search for the route that conserves the most
energy.
Select to search for a route that is easiest to drive, with
few right and left turns. Using this option, the program
allows you to avoid combinations of smaller roads and
to take the expressway.

ROUTE GUIDANCE
236
4. 6HDUFKIRUDGHVWLQDWLRQ
:3

”Select the route’s destination using the same method
as described previously.

”After selecting a new destination, you are returned to
the list.

”To add another destination, select
at the point
where you want to add a new route point to the list,
and repeat the steps above.
ROUTE ALTERNATIVES
Change the Route settings to perform a new search for the
route being navigated using a different method. You can
even search again by comparing different routes.
1. Display the “Change Route (Change Route)” screen.

:3
2. Select More (More).
3. Select Route Alternatives (Route Alternatives).
4. Select the desired route.

”Using the current search method, three routes are
displayed in order of recommendation.

”
More Results (More Results): Select to search
using a different method. Also, if only a short distance
is being navigated or only a few search candidates
are found, each search method displays only one
route.
5. Select to return to the previous screen.

”The route is searched again using the selected
method. The new recommended route is indicated by
a blue line.

SETUP
246
No. Function
Displays service area information while driving on the
expressway. Select to turn this function on and off.
Select to select the service area information display
items.
When information is available, lane information similar to
<0052005900480055004b004800440047000300550052004400470003005700550044004900bf004600030056004c004a005100560003004c005600030047004c00560053004f0044005c0048004700030044005700030057004b0048000300570052005300
030052004900030057004b00480003>
map. Select to turn this function on and off.
When approaching an expressway exit or a complicated
intersection, the map switches to a 3D display if the
necessary information can be displayed. Select to turn
this function on and off.
Select to turn on the route progress bar which is
displayed as a straight line to the left of the map. This
shows the progress made on the current route. When
a blue arrow is used to indicate position, the arrow
continues to rise as you drive towards your destination.
:D<005c00530052004c00510057005600030044005100470003005700550044004900bf004600030046005200510047004c0057004c005200510056000300440055004800030047004c00560053004f0044005c0048004700030052005100030057004b004800
03>
line.

Siri
252
Siri
Siri®
Siri is a function that allows your iPhone and iPod touch to
be used without any manual operation by connecting your
device to the unit.
To use Siri, connect your device via Bluetooth.
BEFORE USING Siri
This section describes the preparation required to use Siri.

”Register your iPhone or iPod touch in the unit.

:3

”Connect your iPhone or iPod touch to the unit.

:3
‡When using the hands-free system, turn Phone on
(Connected).
‡When listening to music, turn Phone and Audio
device on (Connected).

”Enable Siri in your iPhone or iPod touch settings.
(See Apple website for details.)
”An iPhone and iPod touch data plan: If the data plan
for your iPhone and iPod touch does not provide for
unlimited data usage, additional charges from your
carrier may apply for accessing app-based connected
content via 3G, 4G, Wi-Fi, or 4G LTE wireless
networks.

”Connection to the internet via 3G, 4G, Wi-Fi, or 4G
LTE networks.
NOTE
OAvailable operations will differ based on your iPhone and iPod
touch.
OBe careful not to exceed the data usage limits for your iPhone
and iPod touch. Doing so will result in additional data usage
charges from your phone carrier.

CERTIFICATION
284
Bluetooth

”The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by Fujitsu Ten Limited is under license. Other
trademarks and trade names are those of their respective
owners.
microSDHC

”microSDHC Logo is a trademark of SD-3C,LLC.

WHAT TO DO IF
289
APPENDIX/WHAT TO DO IF/INDEX
10
XWhen registering/connecting a cellular phone
Symptom Likely cause SolutionPage
Cellular
phoneThis
system
A cellular phone cannot be
registered.An incorrect passcode was entered
on the cellular phone.Enter the correct passcode on the
cellular phone.*-
The registration operation has not
been completed on the cellular phone
side.Complete the registration operation
on the cellular phone (approve
registration on the phone).*-
Old registration information remains
on either this system or the cellular
phone.Delete the existing registration
information from both this system and
the cellular phone, then register the
cellular phone you wish to connect to
this system.*181
A Bluetooth connection cannot be
made.Another Bluetooth device is already
connected.Manually connect the cellular phone
you wish to use to this system.-182
Bluetooth function is not enabled on
the cellular phone.Enable the Bluetooth function on the
cellular phone.*-
Automatic Bluetooth connection on
this system is set to off.Set automatic Bluetooth connection
on this system to on when the ignition
switch is turned to the “ACC” or “ON”
position.-187
*: For details, refer to the owner’s manual that came with the cellular phone.

WHAT TO DO IF
291
APPENDIX/WHAT TO DO IF/INDEX
10
XWhen using the Bluetooth message function
Symptom Likely cause SolutionPage
Cellular
phoneThis
system
Messages cannot be viewed.Message transfer is not enabled on
the cellular phone.Enable message transfer on the
cellular phone (approve message
transfer on the phone).*-
Automatic transfer function on this
system is set to off.Set automatic transfer function on
this system to on.- 142
1HZPHVVDJHQRWL¿FDWLRQVDUHQRW
displayed.1RWL¿FDWLRQRI606006(PDLO
reception on this system is set to off.6HWQRWL¿FDWLRQRI606006(PDLO
reception on this system to on.- 142
Automatic message transfer function
is not enabled on the cellular phone.Enable automatic transfer function on
the cellular phone.*-
*: For details, refer to the owner’s manual that came with the cellular phone.

WHAT TO DO IF
292 XIn other situations
Symptom Likely cause SolutionPage
Cellular
phoneThis
system
The Bluetooth connection status is
displayed at the top of the screen
each time the ignition switch is turned
to the “ACC” or “ON” position.&RQQHFWLRQFRQ¿UPDWLRQGLVSOD\RQ
this system is set to on.To turn off the display, set connection
FRQ¿UPDWLRQGLVSOD\RQWKLVV\VWHP
to off.-186
Even though all conceivable
measures have been taken, the
symptom status does not change.The cellular phone is not close
enough to this system.Bring the cellular phone closer to this
system.--
The cellular phone is the most likely
cause of the symptom.Turn the cellular phone off, remove
and reinstall the battery pack, and
then restart the cellular phone.*-
Enable the cellular phone’s Bluetooth
connection.*-
Stop the cellular phone’s security
software and close all applications.*-
Before using an application installed
on the cellular phone, carefully check
its source and how its operation
might affect this system.*-
*: For details, refer to the owner’s manual that came with the cellular phone.

ERROR MESSAGES
297
APPENDIX/WHAT TO DO IF/INDEX
10
Mode Message Cause Action
Bluetooth Audio“Music tracks not supported. Please
check your audio player. (Music
tracks not supported. Please check
your audio player.)”A device that is incompatible with
audio playback was connected.‡Check the device settings.
‡Connect a device that is compatible
with audio playback.
STARLINKPlease disconnect mobile device and
install the STARLINK application on
your mobile device and try again.

Bluetooth disconnected, please
reconnect and try again.

Smartphone data connection is poor,
please try to connect again.‡The STARLINK application has not
been installed on your smartphone.
‡Your smartphone power was turned
OFF.
‡The Bluetooth connection has been
lost.
‡The signal quality is weak.
‡Lines are congested.‡Install the STARLINK application.
‡Turn ON the your smartphone
power.
‡Check the Bluetooth connection.
‡Move the car and connect to
STARLINK again.
‡Wait a short while and connect to
STARLINK again.
‡Start the STARLINK application on
your smartphone, check the service
availability, and then reconnect.
aha“Information acquisition error.
(Information acquisition error.)”When not able to get the requested
information.Please try again (Refresh etc.) later
or reconnect it.
“Poor wireless reception. (Poor
wireless reception.)”When a communication error has
been detected.Please try again in a better
communications environment.
“Entry not recognized. (Entry not
recognized.)”When an invalid operation has been
executed.Please try again (Refresh etc.) later
or reconnect it.
“The station list cannot be acquired.
(The station list cannot be acquired.)”When not able to get the station
information.Please try again (Refresh etc.) later
or reconnect it.

ERROR MESSAGES
298
Mode Message Cause Action
aha“The content cannot be acquired.
(The content cannot be acquired.)”‡When not able to get the content
information.
‡When not able to switch to the Top
content when touching
.‡Please try again (Refresh etc.) later
or reconnect it.
‡Select the desired station again
when the station list appears.
“Action not available. (Action not
available.)”:KHQFRQWHQWVSHFL¿FRSHUDWLRQV
such as “fast forward” or “rewind” are
not available.Please try again (Refresh etc.) later
or reconnect it.
“Failed. (Failed.)”When data transmission failed when
touching
.Please try again later.
“aha communication error - Please
check Owner's Manual. (aha
communication error - Please check
Owner's Manual.)”‡When invalid data is received from
the aha application or there is no
response.
‡When the connection to the aha
application via Bluetooth is not
available.
‡When the data reception from this
unit is rejected.Please try again (Refresh etc.)
later or reconnect it. If it is still not
improved, restart the aha application.
“Please select the type of connection
in “aha Settings”. (Please select the
type of connection in “aha Settings”.)”When aha radio setting is set to
USB (USB) when the Android
device is going to be paired via
Bluetooth.When you want to connect to the aha
application with the Android device,
select Bluetooth (Bluetooth) in
the aha radio setting from the setting
screen.