SUBARU TRIBECA 2009 1.G Service Workshop Manual

COM-4
Horn
COMMUNICATION SYSTEM
3. Horn
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the left and right headlight assemblies.
<Ref. to LI-11, REMOVAL, Headlight Assembly.>
3) Remove the horn bracket mounting bolt (A).
4) Disconnect the harness connector and remove
the horn assembly (B).
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
With 12 V direct current supplied between horn ter-
minals, check that the horn sounds properly.
COM00041
(A)(A)
(B)(B)
COM00020

COM-5
Horn Switch
COMMUNICATION SYSTEM
4. Horn Switch
A: REMOVAL
CAUTION:
Before servicing, be sure to read the notes in
the AB section for proper handling of the driv-
er's airbag module. <Ref. to AB-4, CAUTION,
General Description.>
NOTE:
Horn switch is a unit with the driver's airbag mod-
ule.
1) Disconnect the ground cable from battery.
2) Remove the driver’s airbag module. <Ref. to AB-
15, REMOVAL, Driver’s Airbag Module.>
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
Measure the resistance between horn switch termi-
nal and airbag module bracket.
(1) Airbag module bracket
(2) Horn switch terminal
Switch position Terminal No. Resistance
When horn switch
is pushed.Horn switch ter-
minal and airbag
module bracket
Less than 1 Ω
When horn switch
is not pushed.1 MΩ or more
(2)
(1)
COM00037

COM-6
Horn Switch
COMMUNICATION SYSTEM

CC-2
General Description
CRUISE CONTROL SYSTEM
1. General Description
A: COMPONENT
(1) Engine control module (ECM) (4) Cruise indicator light and cruise
set indicator light
(5) Transmission control module
(TCM)(2) Cruise control command switch
(3) Stop light and brake switch
CC-00369
(1)(4)
(2)(3)(5)

CC-3
General Description
CRUISE CONTROL SYSTEM
B: CAUTION
•Before disassembling or reassembling parts, al-
ways disconnect the battery ground cable from bat-
tery. When repairing the audio, control module, etc.
which are provided with memory functions, record
the memory contents before disconnecting the
ground cable from battery. Otherwise, the memory
will be cleared.
•Reassemble the parts in the reverse order of dis-
assembly unless otherwise indicated.
•Adjust the parts to specifications specified in this
manual.
•Connect the connectors securely during reas-
sembly.
•After reassembly, ensure functional parts oper-
ate properly.
C: PREPARATION TOOL
TOOL NAME REMARKS
Circuit tester Used for measuring resis-
tance and voltage.

CC-4
Cruise Control Unit
CRUISE CONTROL SYSTEM
2. Cruise Control Unit
A: NOTE
The control of cruise control system is carried out in
Engine control module (ECM).
B: REMOVAL
<Ref. to FU(H6DO)-32, REMOVAL, Engine Control
Module (ECM).>
C: INSTALLATION
<Ref. to FU(H6DO)-32, INSTALLATION, Engine
Control Module (ECM).>

CC-5
Cruise Control Command Switch
CRUISE CONTROL SYSTEM
3. Cruise Control Command
Switch
A: REMOVAL
CAUTION:
Before servicing, be sure to read the notes in
the “AB” section for proper handling of the
driver’s airbag module. <Ref. to AB-4, CAU-
TION, General Description.>
1) Set the front wheels in straight ahead position.
2) Turn the ignition switch to OFF.
3) Disconnect the ground cable from battery and
wait for at least 20 seconds before starting work.
4) Using TORX® BIT T30 (1), loosen two TORX®
bolts which secure the driver’s airbag module.
5) Disconnect the airbag module connector on
back of the airbag module.
6) Remove the steering wheel. <Ref. to PS-12, RE-
MOVAL, Steering Wheel.>
7) Remove the four screws to remove the lower
cover from steering wheel.
8) Remove one screw to remove the cruise control
command switch from lower cover.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
Measure the cruise control command switch resis-
tance.
If NG, replace the cruise control command switch.
CC-00018
(1)
CC-00181
Switch Area Terminal No. Standard
CANCEL
SET/COAST
RESUME/
ACCEL
All OFF 2 and 3 Approx. 4 kΩ
CANCEL ON 2 and 3 Less than 1 Ω
SET/COAST ON 2 and 3Approximately
250 Ω
RESUME/
ACCELON 2 and 3Approximately
1500 Ω
MAINOFF 1 and 2 1 MΩ or more
ON 1 and 2 Less than 1 Ω
CC-00182
CC-00252
231

CC-6
Stop Light and Brake Switch
CRUISE CONTROL SYSTEM
4. Stop Light and Brake Switch
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Disconnect the connector from the stop light &
brake switch, and then remove the switch. <Ref. to
BR-37, REMOVAL, Stop Light Switch.>
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
Measure the resistance of brake switch (A) and
stop light switch (B).
If NG, replace the stop light & brake switch.
Switch Pedal Terminal No. Standard
BrakeReleased 1 and 4 Less than 1 Ω
Depressed 1 and 4 1 MΩ or more
Stop lightReleased 2 and 3 1 MΩ or more
Depressed 2 and 3 Less than 1 Ω
CC-00022
1234
(A)
(B)
3214

CC(ETC)(diag)-2
Basic Diagnostic Procedure
CRUISE CONTROL SYSTEM (DIAGNOSTICS)
1. Basic Diagnostic Procedure
A: PROCEDURE
Step Check Yes No
1CHECK MALFUNCTION INDICATOR LIGHT.
1) Start the engine.
2) Make sure the malfunction indicator light
illuminates.
Does the malfunction indicator
light illuminate?
Go to step 5.Go to step 2.
2CHECK CRUISE INDICATOR LIGHT.
Make sure the cruise indicator light blinks.
Does the cruise indicator light
blink?
Go to step 5.Go to step 3.
3CHECK CRUISE CONTROL MAIN SWITCH
OPERATION.
Check cruise control main switch operation.
(Ensure the cruise indicator light illuminates.)
Is the cruise control main
switch tur ned on? (Does the
cruise indicator light illumi-
nate?)
Go to step 4.Go to phenome-
non 1. <Ref. to
CC(ETC)(diag)-9,
DIAGNOSTIC
PROCEDURE
WITH PHENOME-
NON, Diagnostics
with Phenome-
non.>
4CHECK CRUISE CONTROL SET OPERA-
TION.
Check the cruise control setting operation.
Can the cruise control be set
while driving at more than 40
km/h (25 MPH)?
Go to step 6.Go to step 5.
5PERFORM CRUISE CONTROL CANCEL
CONDITIONS DIAGNOSIS.
Perfor m the cr uise control cancel conditions
diagnosis. <Ref. to CC(ETC)(diag)-7, CRUISE
CONTROL CANCEL CONDITIONS DIAGNO-
SIS, OPERATION, Subaru Select Monitor.>
Is DTC displayed? Go to “List of Diag-
nostic Trouble
Code (DTC)”.
<Ref. to
CC(ETC)(diag)-
11, List of Diag-
nostic Trouble
Code (DTC).>
Go to phenome-
non 2. <Ref. to
CC(ETC)(diag)-9,
DIAGNOSTIC
PROCEDURE
WITH PHENOME-
NON, Diagnostics
with Phenome-
non.>
6CHECK CRUISE SET INDICATOR LIGHT.
Make sure the cruise set indicator light illumi-
nates.
Does the cruise set indicator
light illuminate?
Go to step 7.Go to phenome-
non 3. <Ref. to
CC(ETC)(diag)-9,
DIAGNOSTIC
PROCEDURE
WITH PHENOME-
NON, Diagnostics
with Phenome-
non.>
7CHECK VEHICLE SPEED IS HELD WITHIN
SET SPEED.
Make sure the vehicle speed is held within set
speed.
Is the vehicle speed kept within
setting speed ±3 km/h (±2
MPH)? (Make sure that on a
level road.)
Go to step 8.Go to phenome-
non 4. <Ref. to
CC(ETC)(diag)-9,
DIAGNOSTIC
PROCEDURE
WITH PHENOME-
NON, Diagnostics
with Phenome-
non.>
8CHECK RESUME/ACCEL OPERATION.
Check the RESUME/ACCEL switch operation.
Does the vehicle speed
increase or return to set speed
after RESUME/ACCEL switch
has been pressed?
Go to step 9.Go to phenome-
non 5. <Ref. to
CC(ETC)(diag)-9,
DIAGNOSTIC
PROCEDURE
WITH PHENOME-
NON, Diagnostics
with Phenome-
non.>

CC(ETC)(diag)-3
Basic Diagnostic Procedure
CRUISE CONTROL SYSTEM (DIAGNOSTICS)
9CHECK SET/COAST OPERATION.
Check the SET/COAST switch operation.
Does the vehicle speed
decrease after SET/COAST
switch has been pressed?
Go to step 10.Go to phenome-
non 6. <Ref. to
CC(ETC)(diag)-9,
DIAGNOSTIC
PROCEDURE
WITH PHENOME-
NON, Diagnostics
with Phenome-
non.>
10 CHECK CANCEL OPERATION.
Check the CANCEL switch operation.
Is the cruise control released
after CANCEL switch has been
pressed?
Go to step 11.Go to phenome-
non 7. <Ref. to
CC(ETC)(diag)-9,
DIAGNOSTIC
PROCEDURE
WITH PHENOME-
NON, Diagnostics
with Phenome-
non.>
11 CHECK CRUISE CONTROL RELEASE OP-
ERATION.
Check the cruise control release operation.
Is the cruise control released
after brake pedal has been
depressed?
Go to step 12.Go to phenome-
non 8. <Ref. to
CC(ETC)(diag)-9,
DIAGNOSTIC
PROCEDURE
WITH PHENOME-
NON, Diagnostics
with Phenome-
non.>
12 CHECK CRUISE CONTROL RELEASE OP-
ERATION.
Check the cruise control release operation.
Is the cruise control released
after shifting to the neutral
position?
Finish the diagno-
sis.
Go to phenome-
non 9. <Ref. to
CC(ETC)(diag)-9,
DIAGNOSTIC
PROCEDURE
WITH PHENOME-
NON, Diagnostics
with Phenome-
non.>
Step Check Yes No