ignition wiring SUZUKI GRAND VITARA 1998 2.G Service User Guide

YH4
GRAND
VITARA
5C
PARKING AND REAR BRAKE 5C-1
SECTION 5C
PARKING AND REAR BRAKE
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
NOTE:
All brake fasteners are important attaching parts in that they could affect the performance of vital parts
and systems, and / or could result in major repair expense. They must be replaced with one of same part
number or with an equivalent part if replacement becomes necessary. Do not use a replacement part of
lesser quality or substitute design. Torque values must be used as specified during reassembly to assure
proper retention of all parts. There is to be no welding as it may result in extensive damage and weakening
of the metal.
CONTENTS
GENERAL DESCRIPTION5C- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drum Brake Assembly5C- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS5C- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECK AND ADJUSTMENT5C- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE5C- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking Brake Lever5C- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking Brake Cable5C- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Drum5C- 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Shoe5C- 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel Cylinder5C-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Back Plate5C-14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS5C-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS5C-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS5C-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
5E1
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-1
GENERAL DESCRIPTION5E1- 2 . . . . . . . . . . . . . .
Brake Hose / Pipe Routing 5E1- 3. . . . . . . . . . . . . .
System Schematic 5E1- 4. . . . . . . . . . . . . . . . . . . .
ABS Component Parts Location 5E1- 5. . . . . . . .
ABS Hydraulic Unit/Control Module
Assembly 5E1- 6. . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS5E1- 7 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precaution in Diagnosing Troubles 5E1- 7. . . . . .
ABS Diagnostic Flow Table 5E1- 8. . . . . . . . . . . . EBD Warning Lamp (Brake Warning
Lamp) Check 5E1-11. . . . . . . . . . . . . . . . . . . . . . .
ªABSº Warning Lamp Check 5E1-11. . . . . . . . . . .
Diagnostic Trouble Code (DTC) Check
(Using ªABSº Warning Lamp) 5E1-11. . . . . . . . .
DTC Check (Using SUZUKI Scan
Tool) 5E1-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC)
Clearance 5E1-13. . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 5E1
ANTILOCK BRAKE SYSTEM (ABS)
(OPTIONAL)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
NOTE:
All brake fasteners are important attaching parts in that they could affect the performance of vital parts
and systems, and / or could result in major repair expense. They must be replaced with one of same part
number or with an equivalent part if replacement becomes necessary. Do not use a replacement part of
lesser quality or substitute design. Torque values must be used as specified during reassembly to assure
proper retention of all parts. There is to be no welding as it may result in extensive damage and weakening
of the metal.
CONTENTS

YH4
GRAND
VITARA
7A-6 MANUAL TRANSMISSION (TYPE 1)
3, (a)
1. Coupler
2. Clamp3. 4WD switch
4. Boot No. 2
1. Back up light switch
2. 4WD switch
1. Back up light switch coupler
2. Front propeller shaft
SWITCHES
TRANSFER 4WD SWITCH
1) Remove console box and lift transmission control lever boots
No. 2 and No. 3. (Refer to page 7A-4.)
2) Remove transfer control lever boot No. 2, unclamp wiring on
transfer case to free it and pull off coupler.
3) Replace switch and connect as it was.
Tightening Torque
(a): 20 N
.m (2.0 kg-m, 14.5 lb-ft)
4) Turn ON ignition switch, shift transfer shift control lever to 4WD
position and check that indicator lights. Turn OFF switch after
checking.
NOTE:

When removing and reinstalling switch, use care not to let
dust enter transfer box inside.

Make sure to reset clamp for wiring which is located
where invisible directly.

It is recommended to work on transfer shift control lever
boot No. 1 from underside of vehicle on lift.

Identify this switch by its leg part which is different for that
of back up light switch.
BACK UP LIGHT SWITCH
WARNING:
Refrain from work while exhaust center pipe is hot.
REMOVAL AND INSTALLATION
NOTE:
When replacing switch, use care not to let dust enter transmis-
sion through switch hole.
1) Lift up vehicle.
2) Remove coupler(s) for switch wiring.

YH4
GRAND
VITARA
1. Back up light switch
2. Exhaust center pipe
1. Ohmmeter
2. Back up light switch or 4WD switch1, (a)
[Type 1]
[Type 2]
MANUAL TRANSMISSION (TYPE 1) 7A-7
3) Replace switch, connect and clamp as they were.
Tightening Torque
(a): 20 N
.m (2.0 kg-m, 14.5 lb-ft) (Type 1)
(a): 45 N
.m (4.5 kg-m, 32.5 lb-ft) (Type 2)
4) When back up light switch has been replaced, check switch for
proper function with ignition switch turned ON and gear shifted
to reverse position. Turn OFF switch after checking its function.
INSPECTION OF 4WD SWITCH AND BACK UP LIGHT
SWITCH
1) Undo clamp and disconnect coupler of back up light switch
and / or 4WD switch.
2) Function of back up light switch can be checked as shown in fig-
ure.
There should be conduction at these terminals only when shift
lever is shifted to reverse position.
3) Function of transfer 4WD switch can be checked in the same
manner as back up light switch.
There should be conduction at these terminals when shift lever
is shifted to 4H, and 4L positions.
Upon completion of check, connect coupler and clamp wiring har-
ness as they were.
NOTE:
When replacing switch(es), use care not to let dust enter trans-
mission through switch hole(s).

YH4
GRAND
VITARA
7B1
AUTOMATIC TRANSMISSION (4 A / T) 7B1-1
GENERAL DESCRIPTION7B1- 3 . . . . . . . . . . . . . .
CLUTCH / BRAKE FUNCTIONS 7B1- 5. . . . . . . . .
TABLE OF COMPONENT OPERATION 7B1- 6. . .
ELECTRONIC SHIFT CONTROL
SYSTEM 7B1- 7. . . . . . . . . . . . . . . . . . . . . . . . . . .
AUTOMATIC TRANSMISSION
DIAGNOSIS7B1-17 . . . . . . . . . . . . . . . . . . . . . . . . . .
PRECAUTION IN DIAGNOSING
TROUBLE 7B1-20. . . . . . . . . . . . . . . . . . . . . . . . . .
AUTOMATIC TRANSMISSION
DIAGNOSTIC FLOW TABLE 7B1-21. . . . . . . . . .
Customer Problem Inspection Form 7B1-23. . .
Malfunction Indicator lamp (MIL)
Check 7B1-24. . . . . . . . . . . . . . . . . . . . . . . . . . .
ªO / D OFFº Lamp Check 7B1-24. . . . . . . . . . . . .
ªPOWERº Lamp Check 7B1-24. . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC)
Check 7B1-24. . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC)
Clearance 7B1-24. . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) Table7B1-24 . . .
Fail-Safe Table 7B1-25. . . . . . . . . . . . . . . . . . . . .
Visual Inspection 7B1-26. . . . . . . . . . . . . . . . . . .
A / T Basic Check 7B1-27. . . . . . . . . . . . . . . . . . .
Trouble Diagnosis Table 1 7B1-28. . . . . . . . . . .
Trouble Diagnosis Table 2 7B1-28. . . . . . . . . . . Trouble Diagnosis Table 3 7B1-29. . . . . . . . . . .
Scan Tool Data 7B1-30. . . . . . . . . . . . . . . . . . . . .
Inspection of PCM and Its Circuit 7B1-30. . . . .
Wire Harness and Connectors 7B1-30. . . . . . . .
Diagnostic Flow Table A-1 7B1-31. . . . . . . . . . .
Diagnostic Flow Table A-2 7B1-33. . . . . . . . . . .
Table B-1 ªO / D OFFº Light Circuit
Check 7B1-35. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-2 ªO / D OFFº Light Circuit
Check 7B1-36. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-3 ªPOWERº Light Circuit
Check 7B1-37. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-4 ªPOWERº Light Circuit
Check 7B1-38. . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0705 Transmission Range
Sensor (Switch) Circuit Malfunction 7B1-39. .
DTC P0715 Input / Turbine Speed
Sensor Circuit Malfunction 7B1-42. . . . . . . . . .
DTC P0720 Output Speed Sensor
Circuit Malfunction 7B1-44. . . . . . . . . . . . . . . . .
DTC P0741 TCC Solenoid Valve
Performance or Stuck Off 7B1-46. . . . . . . . . . .
DTC P0743 TCC Solenoid Electrical 7B1-47. .
DTC P0751 Shift Solenoid Valve-A (#1)
Performance or Stuck Off 7B1-49. . . . . . . . . . .
DTC P0756 Shift Solenoid Valve-B (#2)
Performance or Stuck Off 7B1-49. . . . . . . . . . .
SECTION 7B1
AUTOMATIC TRANSMISSION
(4 A
/
T)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS

YH4
GRAND
VITARA
G16 / J20 Engines
H25 Engine
1. PCM
2. J / B
3. O / D cut switch
4. P / N change switch
5. J / C
1. PCM
2. Fuse
3. O / D cut switch
4. P / N change switch
5. J / C
6. J / C
AUTOMATIC TRANSMISSION (4 A / T) 7B1-35
DIAGNOSTIC FLOW TABLE B-1 ªO / D OFFº LIGHT CIRCUIT CHECK
(ªO / D OFFº LIGHT DOESN'T LIGHT AT IGNITION SWITCH ON BUT
ENGINE STARTS UP)
WIRING DIAGRAM
TROUBLESHOOTING
STEPACTIONYESNO
1ªO / D OFFº light circuit check:
(1) With ignition switch OFF, disconnect
couplers from PCM.
(2) Using service wire, connect E61-20
(G16 / J20 engines) or E61-7 (H25 engine)
terminal of disconnected PCM coupler and
ground.
Does ªO / D OFFº light turn ON at ignition
switch ON?Poor E61-20 (G16 / J20
engines) or E61-7 (H25
engine) terminal
connection.
If OK, substitute a known-
good PCM and recheck.Bulb burned out or faulty
ªW / Bº, ªB / Wº wire.

YH4
GRAND
VITARA
7B1-36 AUTOMATIC TRANSMISSION (4 A / T)
Switch ON
positionSwitch OFF
positionSwitch ON
position
Switch OFF
position
DIAGNOSTIC FLOW TABLE B-2 ªO / D OFFº LIGHT CIRCUIT CHECK
(ªO / D OFFº LIGHT COMES ON STEADILY)
WIRING DIAGRAM ± Refer to Table B-1 in this section.
TROUBLESHOOTING
STEPACTIONYESNO
1Check O / D cut Switch Position.
Is O / D cut switch turned OFF (Is switch button at OFF
position)?Go to Step 2.Turn O / D cut switch
OFF.
2Check Lamp Circuit for Short.
1) Turn ignition switch OFF and disconnect PCM
connectors.
2) Turn ignition switch ON.
Does ªO / D OFFº lamp come ON steadily?ªW / Bº circuit shorted
to ground.Go to Step 3.
3Check O / D cut Switch Circuit.
1) Check resistance between terminal E61-33
(G16 / J20 engines) or E61-14 (H25 engine) of
disconnected PCM connector and body ground with
O / D cut switch OFF.
Is continuity indicated?Go to Step 4.Check PCM ground
circuit for open.
If ground circuit is
OK, substitute a
known-good PCM
and recheck.
4Check O / D cut Switch for Operation.
1) Remove console box.
2) Disconnect O / D cut switch connector.
3) Check continuity between switch terminals under
each condition below.
Switch OFF position: No continuity
Switch ON position: Continuity
Is check result satisfactory?ªY / Rº circuit shorted
to ground.Replace O / D cut
switch.
Fig. for Step 1. Fig. for Step 4.

YH4
GRAND
VITARA
G16 / J20 Engines
H25 Engine
1. PCM
2. J / B
3. O / D cut switch
4. P / N change switch
5. J / C
1. PCM
2. Fuse
3. O / D cut switch
4. P / N change switch
5. J / C
6. J / C
AUTOMATIC TRANSMISSION (4 A / T) 7B1-37
DIAGNOSTIC FLOW TABLE B-3 ªPOWERº LIGHT CIRCUIT CHECK
(ªPOWERº LIGHT DOESN'T LIGHT AT IGNITION SWITCH ON BUT
ENGINE STARTS UP)
WIRING DIAGRAM
TROUBLESHOOTING
STEPACTIONYESNO
1ªPOWERº light circuit check:
(1) With ignition switch OFF, disconnect
couplers from PCM.
(2) Using service wire, connect E61-21 (G16 /
J20 engines) or E61-10 (H25 engine)
terminal of disconnected PCM coupler and
ground.
Does ªPOWERº light turn ON at ignition switch
ON?Poor E61-21 (G16 / J20
engines) or E61-10 (H25
engine) terminal
connection.
If OK, substitute a known-
good PCM and recheck.Bulb burned out or faulty
ªGr / Blº, ªB / Wº wire.

YH4
GRAND
VITARA
7B1-38 AUTOMATIC TRANSMISSION (4 A / T)
ª5º
ª4º
DIAGNOSTIC FLOW TABLE B-4 ªPOWERº LIGHT CIRCUIT CHECK
(ªPOWERº LIGHT COMES ON STEADILY)
WIRING DIAGRAM ± Refer to Table B-3 in this section.
TROUBLESHOOTING
STEPACTIONYESNO
1Check Power / Normal Change Switch Position.
Is switch button at Normal position?Go to Step 2.Set Power / Normal
change switch at
Normal position.
2Check Lamp Circuit for Short.
1) Turn ignition switch OFF and disconnect PCM
connectors.
2) Turn ignition switch ON.
Does ªPOWERº lamp come ON steadily?ªGr / Blº circuit
shorted to ground.Go to Step 3.
3Check Power / Normal Change Switch Circuit.
1) Check resistance between terminal E61-31
(G16/J20 engines) or E61-9 (H25 engine) of
disconnected PCM connector and body ground with
P / N change switch OFF.
Is continuity indicated?Go to Step 4.Check PCM ground
circuit for open.
If ground circuit is
OK, substitute a
known-good PCM
and recheck.
4Check Power / Normal Change Switch for Operation.
1) Remove Power / Normal change switch.
2) Check continuity between switch terminals ª4º and
ª5º under each condition below.
Normal position: No continuity
Power position: Continuity.
Is check result satisfactory?ªOr / Blº circuit
shorted to ground.Replace Power /
Normal change
switch.
Fig. for Step 1. Fig. for Step 4.

YH4
GRAND
VITARA
G16/J20 Engines H25 Engine
G16/J20 Engines
H25 Engine
1. PCM
2. A / T input speed sensor 11 1 0
Bl / Y Bl / G16 8
Bl / Y Bl / G
7B1-42 AUTOMATIC TRANSMISSION (4 A / T)
DTC P0715 (DTC NO.76) INPUT / TURBINE SPEED SENSOR CIRCUIT MALFUNCTION
WIRING DIAGRAM
DTC DETECTING CONDITION AND TROUBLE AREA
DTC DETECTING CONDITIONTROUBLE AREA
Input speed sensor detected speed is lower than spec-
ification while vehicle running under all of the following
conditions:

at higher than 10 km / h (7 mph) with 1st gear in D
range for 1 sec. or more.

at higher than 20 km / h (13 mph) with 2nd gear in D
range for 2 sec. or more.

at higher than 30 km / h (20 mph) with 3rd gear in D
range for 2 sec. or more.
(2 driving cycles detection logic)
Input speed sensor and its circuit

PCM
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Connect scan tool to DLC with ignition switch OFF, if available.
2) Clear DTC.
3) Start engine and turn O / D cut switch ON.
4) Shift select lever to D range and start vehicle.
5) Keep vehicle speed at higher than 10 km / h (7 mph) with 1st gear in D range for 2 sec. or more.
6) Increase vehicle speed and keep it at higher than 20 km / h (13 mph) with 2nd gear in D range for 2 sec. or more.
7) Increase vehicle speed and keep it at higher than 30 km / h (20 mph) with 3rd gear in D range for 2 sec. or more.
8) Stop vehicle.
9) Check DTC and / or pending DTC.