Engine fuel SUZUKI GRAND VITARA 1999 2.G Service User Guide

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-49
DTC P0751 SHIFT SOLENOID VALVE-A (#1) PERFORMANCE OR STUCK OFF
DTC P0756 SHIFT SOLENOID VALVE-B (#2) PERFORMANCE OR STUCK OFF
DTC DETECTING CONDITION AND TROUBLE AREA
DTC DETECTING CONDITIONTROUBLE AREA
While running in D range, gear change control from
PCM to A / T does not agree with actual A / T gear posi-
tion even though solenoid valve is electrically in good
condition.
(A / T gear position is calculated based on engine
speed signal and vehicle speed sensor signal.)
(2 driving cycles detection logic)DTC P0751:

Shift solenoid valve-A stuck or leakage.

2-3 shift valve stuck.

Valve body fluid passage clogged.

Mechanical malfunction in transmission.
(Direct clutch malfunction)
DTC P0756:

Shift solenoid valve-B stuck or leakage.

1-2 shift valve stuck.

3-4 shift valve stuck.

Valve body fluid passage clogged.

Mechanical malfunction in transmission.
(2nd brake malfunction)
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Connect scan tool to DLC with ignition switch OFF.
2) Clear DTC, pending DTC and freeze frame data in PCM memory by using scan tool and check fuel level meter
indication is 1 / 4 or more.
3) Start engine, warm it up to normal operating temperature and shift transfer lever to ª2Hº or ª4Hº range.
4) Increase vehicle speed with D range, and check that gear position changes from 1st to 2nd, 3rd and 4th in that
order as vehicle speed increases, referring to ªGear Shift Diagramº in this section.
5) Stop vehicle and check pending DTC and DTC by using scan tool.
TROUBLESHOOTING
STEPACTIONYESNO
1Was ªA / T DIAG. FLOW TABLEº performed?Go to Step 2.Go to ªA / T DIAG.
FLOW TABLEº.
2Shift solenoid valve-A or -B operation check:
1) Check shift solenoid valve-A or -B for operation
referring to ªSolenoid Valves Operation Checkº
section.
Is it in good condition?Go to Step 3.Faulty shift solenoid
valve-A or -B.
3Valve body check:
1) Check valve body and its passage referring to
ªUnit Repairº section.
Are they in good condition?Overhaul and repair
automatic transmis-
sion.Faulty valve body.

YH4
GRAND
VITARA
8C
INSTRUMENTATION / DRIVER INFORMATION 8C-1
GENERAL DESCRIPTION8C- 2 . . . . . . . . . . . . . .
Cautions in Servicing 8C- 2. . . . . . . . . . . . . . . . .
Symbols and Marks 8C- 2. . . . . . . . . . . . . . . . . . .
Wiring Color Symbols 8C- 2. . . . . . . . . . . . . . . . .
Abbreviations 8C- 2. . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector 8C- 2. . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay 8C- 2. . . . . . . . . . . . . . . . . .
Power Supply Diagram 8C- 2. . . . . . . . . . . . . . . .
Combination Meter 8C- 2. . . . . . . . . . . . . . . . . . .
DIAGNOSIS8C- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speedometer and VSS 8C- 4. . . . . . . . . . . . . . . .
Fuel Meter / Fuel Gauge Unit 8C- 4. . . . . . . . . . . .
Engine Coolant Temp. (ECT) Meter and
Sensor 8C- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pressure Light 8C- 4. . . . . . . . . . . . . . . . . . . .
Brake and Parking Brake Warning
Light 8C- 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Light Remainder Warning Buzzer 8C- 5. . . . . . . Seat Belt Warning Light (If Equipped) 8C- 5. . .
Ignition Key Remainder Warning
Buzzer (If Equipped) 8C- 5. . . . . . . . . . . . . . . . .
Cigarette Lighter and Accessory Socket 8C- 5.
ON-VEHICLE SERVICE8C- 6 . . . . . . . . . . . . . . . .
Ignition (Main) Switch 8C- 6. . . . . . . . . . . . . . . . .
Combination Meter 8C- 7. . . . . . . . . . . . . . . . . . .
Speedometer and VSS 8C- 8. . . . . . . . . . . . . . . .
Fuel Meter / Fuel Gauge Unit 8C- 9. . . . . . . . . . . .
Engine Coolant Temp. (ECT) Meter and
Sensor 8C-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pressure Light 8C-11. . . . . . . . . . . . . . . . . . . .
Brake and Parking Brake Warning
Light 8C-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition Key Remainder (If Equipped) /
Light Remainder Warning Buzzer 8C-12. . . . . .
Door Switch 8C-13. . . . . . . . . . . . . . . . . . . . . . . . .
Seat Belt Warning Light (If Equipped) 8C-13. . .
SECTION 8C
INSTRUMENTATION/DRIVER INFORMATION
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS

YH4
GRAND
VITARA
1. Tachometer
2. Speedometer
3. Fuel level meter
4. Water temperature meter
5. Turn signal pilot light (LH)
6. 4WD indicator (if equipped)
7. ABS warning light (if equipped)
8. Immobilizer warning light (if equipped)
9. CHECK ENGINE light
10. Turn signal pilot light (RH)11. AIR BAG warning light (if equipped)
12. O / D OFF light (A / T vehicle only)
13. Fasten seat belt light (if equipped)
14. High beam light
15. Oil pressure warning light
16. Charge warning light
17. Brake and parking brake warning light
18. POWER indicator light (A / T vehicle only)
19. Shift position indicator (A / T vehicle, if equipped)or
CHECK
ENGINEor
ABS
8C-2 INSTRUMENTATION / DRIVER INFORMATION
GENERAL DESCRIPTION
CAUTIONS IN SERVICING
Refer to Section 8.
SYMBOLS AND MARKS
Refer to Section 8.
WIRING COLOR SYMBOLS
Refer to Section 8.
ABBREVIATIONS
Refer to Section 8.
JOINT CONNECTOR
Refer to Section 8.
FUSE BOX AND RELAY
Refer to Section 8.
POWER SUPPLY DIAGRAM
Refer to Section 8.
COMBINATION METER

YH4
GRAND
VITARA
1. To door switch (driver side) B / Bl
2. To transmission range switch G / Bl
(A / T vehicle only, if equipped) L
3. To transmission range switch G / O
(A / T vehicle only, if equipped) 2
4. To transmission range switch Y / G
(A / T vehicle only, if equipped) D
5. To transmission range switch O / Bl
(A / T vehicle only, if equipped) N
6. To transmission range switch O / G
(A / T vehicle only, if equipped) P
7. To transmission range switch R
(A / T vehicle only, if equipped) R
8. To ground B
9. To PCM (A / T vehicle only) W / B
10. To ECT sensor Y / W
11. To fuel level gauge Bl / W
12. To ground B / Y
13. To combination switch G / Y
NOTE:
Terminal arrangement of coupler viewed from harness side.
Coupler A Coupler B Coupler C
Coupler A Coupler B Coupler C
1. Blank ÐÐ
2. Blank ÐÐ
3. To ignition switch B / W
4. Blank ÐÐ
5. To ABS control module Bl / O
(if equipped)
6. To PCM (A / T vehicle only) Gr / Bl
7. To ABS control module Br
(if equipped)
8. To VSS Bl / Y
9. To combination switch G / R
10. To SDM (if equipped) Y / G or Bl
11. To main fuse W / Bl
12. To fuse box W
13. To combination switch R
14. To ECM (PCM for A / T vehicle) V
(if equipped)
15. To ECM (PCM for A / T vehicle) V / Y
16. To ECM (PCM for A / T vehicle) O / B
(if equipped)1. To ground B
2. To ECM (PCM for A / T vehicle) Br
3. To ignition switch (if equipped) V / R
4. To brake fluid level switch R / B
5. To parking brake switch V
6. To seat belt switch (if equipped) Gr / R
7. To generator W / R
8. To oil pressure switch Y / B
9. To combination switch R / Y
10. To ignition switch (if equipped) Bl / R or CHECK
or ENGINE
or ABSif equipped
if equippedif equipped
INSTRUMENTATION / DRIVER INFORMATION 8C-3

YH4
GRAND
VITARA
8C-4 INSTRUMENTATION / DRIVER INFORMATION
DIAGNOSIS
NOTE:
Fuse name (ª º) in the table below is shown on the fuse box cover (Hard Top Model) or the junction box
(Canvas Top Model).
SPEEDOMETER AND VSS
TroublePossible CauseCorrection
Speedometer shows no
operation
ªIG / METERº fuse blown (Hard Top
Model)
ªIGº fuse blown (Canvas Top Model)

VSS faulty

Printed plate in combination meter
faulty

Speedometer faulty

Wiring or grounding faultyReplace fuse to check for short
Replace VSS
Replace printed plate
Replace speedometer
Repair
FUEL METER / FUEL GAUGE UNIT
TroublePossible CauseCorrection
Fuel meter shows no
operation
ªIG / METERº fuse blown (Hard Top
Model)
ªIGº fuse blown (Canvas Top Model)

Fuel gauge unit faulty

Printed plate in combination meter
faulty

Fuel meter faulty

Wiring or grounding faultyReplace fuse to check for short
Replace fuel gauge unit
Replace printed plate
Replace fuel meter
Repair
ENGINE COOLANT TEMP. (ECT) METER AND SENSOR
TroublePossible CauseCorrection
Engine coolant temp.
meter shows no operation
ªIG / METERº fuse blown (Hard Top
Model)
ªIGº fuse blown (Canvas Top Model)

ECT meter faulty

Printed plate in combination meter
faulty

ECT sensor faulty

Wiring or grounding faultyReplace fuse to check for short
Replace ECT meter
Replace printed plate
Replace ECT sensor
Repair
OIL PRESSURE LIGHT
TroublePossible CauseCorrection
Oil pressure warning light
does not light up
Bulb in combination meter blown

ªIG / METERº fuse blown (Hard Top
Model)
ªIGº fuse blown (Canvas Top Model)

Printed plate in combination meter
faulty

Oil pressure switch faulty

Wiring or grounding faultyReplace bulb
Replace fuse to check for short
Replace printed plate
Replace oil pressure switch
Repair

YH4
GRAND
VITARA
0.5TIME (sec.) Ignition switch ON
High Immobilizer
control system
is normal
Immobilizer
control system
is abnormalLow
0.5 0.5 0.5 0.5
High
Low
0.5TIME (sec.) Ignition switch ON
High Immobilizer
control system
is normal
Immobilizer
control system
is abnormalLow
0.5 0.5 0.5 0.5
High
Low
IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED) 8G-5
<Vehicle equipped with monitor coupler>
With the diagnosis switch terminal of monitor coupler for
ECM / PCM not grounded, the ignition switch turned ON (but the en-
gine at stop) and regardless of the condition of the electronic fuel
injection system, ECM / PCM indicates whether a trouble has oc-
curred in the immobilizer control system or not by causing the mal-
function indicator lamp to flash or turn ON.
Malfunction indicator lamp is ON:
No trouble exists in the immobilizer control system.
Malfunction indicator lamp is flashing:
ECM / PCM or Immobilizer Control Module has detected some
trouble in the immobilizer control system.
NOTE:
As soon as the ignition switch is turned ON, ECM / PCM and Im-
mobilizer Control Module diagnose if a trouble has occurred
in the immobilizer control system. While the diagnosis is being
made, the malfunction indicator lamp stays ON and if the diag-
nosis result is ªabnormalº, it immediately changes to flashing
but if the result is ªnormalº, it remains ON. Diagnosis takes
about 3 seconds at maximum.
<Vehicle not equipped with monitor coupler>
With the ignition switch turned ON (but the engine at stop) regard-
less of the condition of the electronic fuel injection system,
ECM / PCM indicates whether a trouble has occurred in the immobi-
lizer control system or not by causing the immobilizer indicator lamp
to flash or turn ON.
Immobilizer indicator lamp is ON:
No trouble exists in the immobilizer control system.
Immobilizer indicator lamp is flashing:
ECM / PCM or Immobilizer Control Module has detected some
trouble in the immobilizer control system.
NOTE:
As soon as the ignition switch is turned ON, ECM / PCM and Im-
mobilizer Control Module diagnose if a trouble has occurred
in the immobilizer control system. While the diagnosis is being
made, the Immobilizer indicator lamp stays ON and if the diag-
nosis result is ªabnormalº, it immediately changes to flashing
but if the result is ªnormalº, it remains ON. Diagnosis takes
about 3 seconds at maximum.
When ECM / PCM and Immobilizer Control Module detects a
trouble which has occurred in the above areas, it stores DTC corre-
sponding to the exact trouble area in ECM / PCM and Immobilizer
Control Module memory.
DTCs stored in memory of each controller (Immobilizer Control
Module and ECM / PCM) can be read by using the procedure de-
scribed in ªDIAGNOSTIC TROUBLE CODE CHECK (IMMOBILIZ-
ER CONTROL MODULE)º and ªDIAGNOSTIC TROUBLE CODE
CHECK (ECM / PCM)º in this section.

YH4
GRAND
VITARA
8G-6 IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED)
1. Immobilizer diagnostic coupler
DIAGNOSIS
ECM / PCM and Immobilizer Control Module have on-board diag-
nostic system (a system self-diagnosis function) as described pre-
viously.
Investigate where the trouble is by referring to ªDiagnostic Flow
Tableº and ªDiagnostic Trouble Code Tableº on later pages.
PRECAUTIONS IN DIAGNOSING TROUBLES
[PRECAUTIONS IN IDENTIFYING DIAGNOSTIC TROUBLE CODE]
ECM / PCM
<Vehicle equipped with monitor coupler>

Before identifying diagnostic trouble code indicated by malfunc-
tion indicator lamp, don't disconnect couplers from ECM / PCM,
battery cable from battery, ECM / PCM ground wire harness from
engine.
Such disconnection will clear trouble codes for electronic fuel in-
jection system stored in memory of ECM / PCM.

If abnormality or malfunction lies in two or more areas, malfunc-
tion indicator lamp indicates applicable codes three times each.
And flashing of these codes is repeated as long as diagnosis ter-
minal is grounded and ignition switch is held at ON position.

When ECM / PCM detects a trouble in both electronic fuel injec-
tion system and immobilizer control system, malfunction indicator
lamp indicates trouble codes of both systems alternately while the
ignition switch is turned ON and the diagnosis terminal is
grounded.

Take a note of diagnostic trouble code indicated first.
<Vehicle not equipped with monitor coupler>

Before identifying diagnostic trouble code indicated through Su-
zuki scan tool, don't disconnect couplers from ECM / PCM, bat-
tery cable from battery, ECM / PCM ground wire harness from en-
gine.
Such disconnection will clear trouble codes for electronic fuel in-
jection system stored in memory of ECM / PCM.

Take a note of diagnostic trouble code indicated first.
Immobilizer Control Module

Take a note of diagnostic trouble code indicated first.