Stall SUZUKI GRAND VITARA 1999 2.G Service Workshop Manual

YH4
GRAND
VITARA
0A
GENERAL INFORMATION 0A-1
SECTION 0A
GENERAL INFORMATION
CONTENTS
HOW TO USE THIS MANUAL0A- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PRECAUTIONS0A- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precautions for Vehicle Equipped with a Supplemental Restraint (Air Bag) System 0A- 3. . . . . . . . . . . . . . . .
Diagnosis0A- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Servicing and Handling0A- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Precautions0A- 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precautions for Catalytic Converter 0A- 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precautions for Electrical Circuit Service 0A-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Circuit Inspection Procedure 0A-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intermittent and Poor Connection 0A-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precaution for Installing Mobile Communication Equipment 0A-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IDENTIFICATION INFORMATION0A-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Body Number0A-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Identification Number0A-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmission Identification Number 0A-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARNING, CAUTION AND INFORMATION LABELS0A-18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VEHICLE LIFTING POINTS0A-19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ABBREVIATIONS MAY BE USED IN THIS MANUAL0A-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
METRIC INFORMATION0A-23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Metric Fasteners0A-23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fasteners Strength Identification 0A-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard Tightening Torque0A-24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
6) Install oil pump. Refer to ªOil pumpº.
7) Install flywheel (for M/T vehicle) or drive plate (for A/T vehicle).
Using special tool, lock flywheel or drive plate, and tighten
flywheel or drive plate bolts to specified torque.
Special Tool
(A): 09924-17810
Tightening Torque
(c): 78 N
.m (7.8 kg-m, 56.0 lb-ft)1. Flywheel bolts or drive plate bolts for A/T vehicle1, (c)
0A-2 GENERAL INFORMATION
HOW TO USE THIS MANUAL
1) There is a TABLE OF CONTENTS FOR THE WHOLE MANUAL
on the third page of this manual, whereby you can easily find the
section that offers the information you need. Also, there is a
CONTENTS on the first page of EACH SECTION, where the
main items in that section are listed.
2) Each section of this manual has its own pagination. It is indicated
at the top of each page along with the Section name.
3) The SPECIAL TOOL usage and TORQUE SPECIFICATION are
given as shown in figure below.
4) A number of abbreviations are used in the text.
For their full explanations, refer to ªABBREVIATIONS MAY BE
USED IN THIS MANUALº of this section.
5) The SI, metric and foot-pound systems are used as units in this
manual.
6) DIAGNOSIS are included in each section as necessary.
7) At the end of each section, there are descriptions of SPECIAL
TOOLS, REQUIRED SERVICE MATERIALS and TIGHT-
ENING TORQUE SPECIFICATIONS that should be used for the
servicing work described in that section.

YH4
GRAND
VITARA
1. Air bag wire harness
2. Passenger air bag
(inflator) module
3. SDM
4. DLC5. Contact coil
6. Driver air bag (inflator)
module
7. Seat belt pretensioner
(if equipped)
GENERAL INFORMATION 0A-3
PRECAUTIONS
PRECAUTION FOR VEHICLES EQUIPPED
WITH A SUPPLEMENTAL RESTRAINT
(AIR BAG) SYSTEM
WARNING:

The configuration of air bag system parts are as shown in
the figure. When it is necessary to service (remove, rein-
stall and inspect) these parts, be sure to follow proce-
dures described in SECTION 10B. Failure to follow proper
procedures could result in possible air bag system activa-
tion, personal injury, damage to parts or air bag system
being unable to activate when necessary.

If the air bag system and another vehicle system both
need repair, SUZUKI recommends that the air bag system
be repaired first, to help avoid unintended air bag system
activation.

Do not modify the steering wheel, dashboard, or any other
air bag system components. Modifications can adversely
affect air bag system performance and lead to injury.

If the vehicle will be exposed to temperatures over 93
C
(200
F) (for example, during a paint baking process), re-
move the air bag system components beforehand to avoid
component damage or unintended air bag system activa-
tion.
DIAGNOSIS

When troubleshooting air bag system, be sure to follow
ªDIAGNOSISº in SECTION 10B. Bypassing these proce-
dures may result in extended diagnostic time, incorrect diag-
nosis, and incorrect parts replacement.

Never use electrical test equipment other than that specified
in this manual.
WARNING:
Never attempt to measure the resistance of the air bag (in-
flator) modules (driver and passenger) and seat belt preten-
tioners (driver and passenger). It is very dangerous as the
electric current from the tester may deploy the air bag or ac-
tivate the pretensioner.

YH4
GRAND
VITARA
ªAº
0A-8 GENERAL INFORMATION

When removing the battery, be sure to disconnect the nega-
tive cable first and then the positive cable. When reconnect-
ing the battery, connect the positive cable first and then the
negative cable, and replace the terminal cover.

When removing parts that are to be reused, be sure to keep
them arranged in an orderly manner so that they may be rein-
stalled in the proper order and position.

Whenever you use oil seals, gaskets, packing, O-rings, lock-
ing washers, split pins, self-locking nuts, and certain other
parts as specified, be sure to use new ones. Also, before
installing new gaskets, packing, etc., be sure to remove any
residual material from the mating surfaces.

Make sure that all parts used in reassembly are perfectly
clean.

When use of a certain type of lubricant, bond or sealant is
specified, be sure to use the specified type.
ªAº: Sealant 99000-31150

Be sure to use special tools when instructed.
Special Tool
(A): 09917-98221
(B): 09916-58210

YH4
GRAND
VITARA
GENERAL INFORMATION 0A-9

When disconnecting vacuum hoses, attach a tag describing
the correct installation positions so that the hoses can be re-
installed correctly.

After servicing fuel, oil, coolant, vacuum, exhaust or brake
systems, check all lines related to the system for leaks.

For vehicles equipped with fuel injection systems, never dis-
connect the fuel line between the fuel pump and injector
without first releasing the fuel pressure, or fuel can be
sprayed out under pressure.
PRECAUTIONS FOR CATALYTIC CONVERTER
For vehicles equipped with a catalytic converter, use only un-
leaded gasoline and be careful not to let a large amount of un-
burned gasoline enter the converter or it can be damaged.
± Conduct a spark jump test only when necessary, make it as
short as possible, and do not open the throttle.
± Conduct engine compression checks within the shortest
possible time.
± Avoid situations which can result in engine misfire (e.g.
starting the engine when the fuel tank is nearly empty).

YH4
GRAND
VITARA
0A-16 GENERAL INFORMATION

Poor terminal-to-wire connection.
Check each wire harness in problem circuits for poor connection
by shaking it by hand lightly. If any abnormal condition is found,
repair or replace.

Wire insulation which is rubbed through, causing an intermittent
short as the bare area touches other wiring or parts of the vehicle.

Wiring broken inside the insulation. This condition could cause
continuity check to show a good circuit, but if only 1 or 2 strands
of a multi-strand-type wire are intact, resistance could be far too
high.
If any abnormality is found, repair or replace.
PRECAUTION FOR INSTALLING MOBILE
COMMUNICATION EQUIPMENT
When installing mobile communication equipment such as CB (Citi-
zens-Band)-radio or cellular-telephone, be sure to observe the fol-
lowing precautions.
Failure to follow cautions may adversely affect electronic control
system.

Keep the antenna as far away as possible from the vehicle's elec-
tronic control unit.

Keep the antenna feeder more than 20 cm (7.9 in.) away from
electronic control unit and its wire harnesses.

Do not run the antenna feeder parallel with other wire harnesses.

Confirm that the antenna and feeder are correctly adjusted.

YH4
GRAND
VITARA
0B-8 MAINTENANCE AND LUBRICATION
ITEM 1-2
Camshaft Timing Belt Replacement (G16 engine only)
Replace timing belt referring to Section 6A1.
ITEM 1-3
Valve Lash Inspection (G16 engine only)
1) Remove cylinder head cover.
2) Inspect intake and exhaust valve lash and adjust as necessary.
Refer to Section 6A1 for valve lash inspection and adjustment
procedure.
Valve
lash
(ªº)
When cold
(Coolant tempera-
ture is 15 ± 25
C
or 59 ± 77
F)When hot
(Coolant tempera-
ture is 60 ± 68
C
or 140 ± 154
F)
(gap ªaº)
specifica-
tion
Intake0.13 ± 0.17 mm
(0.005 ± 0.007 in.)0.17 ± 0.21 mm
(0.007 ± 0.008 in.)
tion
Exhaust0.23 ± 0.27 mm
(0.009 ± 0.011 in.)0.28 ± 0.32 mm
(0.011 ± 0.013 in.)
3) Install cylinder head cover and tighten bolts to specification.
ITEM 1-4
Engine Oil and Filter Change
WARNING:
New and used engine oil can be hazardous.
Be sure to read ªWARNINGº in General Precaution in Sec-
tion 0A and observe what in written there.
Before draining engine oil, check engine for oil leakage. If any evi-
dence of leakage is found, make sure to correct defective part be-
fore proceeding to the following work.
1) Drain engine oil by removing drain plug.
2) After draining oil, wipe drain plug clean. Reinstall drain plug, and
tighten it securely as specified below.
Tightening Torque
(a): 35 N
.m (3.5 kg-m, 25.5 lb-ft)

YH4
GRAND
VITARA
1. Full level mark (hole)
2. Low level mark (hole)
0B-10 MAINTENANCE AND LUBRICATION
NOTE:
Engine oil capacity is specified. However, note that the
amount of oil required when actually changing oil may
somewhat differ from the data in the table depending on
various conditions (temperature, viscosity, etc.).
7) Check oil filter and drain plug for oil leakage.
8) Start engine and run it for three minutes. Stop it and wait five min-
utes before checking oil level. Add oil, as necessary, to bring oil
level to FULL level mark on dipstick.
NOTE:
Step 1) ± 7) outlined above must be performed with ENGINE
NOT RUNNING. For step 8), be sure to have adequate ven-
tilation while engine is running.
ITEM 1-5
Engine Coolant Change
WARNING:
To help avoid danger of being burned, do not remove radia-
tor cap while engine and radiator are still hot. Scalding fluid
and steam can be blown out under pressure if cap is taken
off too soon.
1) Remove radiator cap when engine is cool.
2) Loosen radiator drain plug to drain coolant.
3) Remove reservoir, which is on the side of radiator, and drain.
4) Tighten plug securely. Also reinstall reservoir.
5) Fill radiator with specified amount of coolant, and run engine for
2 or 3 minutes at idle. This drives out any air which may still be
trapped within cooling system. STOP ENGINE. Add coolant as
necessary until coolant level reaches the filler throat of radiator.
Reinstall radiator cap.

YH4
GRAND
VITARA
MAINTENANCE AND LUBRICATION 0B-11
1. Reservoir
2. FULL level mark
3. LOW level mark
4. Arrow mark
5. Reservoir cap
546) Add coolant to reservoir so that its level aligns with Full mark.
Then, reinstall cap aligning arrow marks on reservoir and cap.
NOTE:
When installing reservoir cap, align arrow marks on reser-
voir and cap.
CAUTION:
When changing engine coolant, use mixture of 50% wa-
ter and 50% ANTIFREEZE / ANTICORROSION COOLANT
for the market where ambient temperature falls lower
than ±16C (3F) in winter, and mixture of 70% water and
30% ANTIFREEZE / ANTICORROSION COOLANT for the
market where ambient temperature doesn't fall lower
than ±16C (3F).
Even in a market where no freezing temperature is antici-
pated, mixture of 70% water and 30% ANTIFREEZE / AN-
TICORROSION COOLANT should be used for the pur-
pose of corrosion protection and lubrication.
ITEM 1-6
Exhaust System Inspection
WARING:
To avoid danger of being burned, do not touch exhaust sys-
tem when it is still hot. Any service on exhaust system
should be performed when it is cool.
When carrying out periodic maintenance, or the vehicle is raised for
other service, check exhaust system as follows:

Check rubber mountings for damage, deterioration, and out of
position.

Check exhaust system for leakage, loose connections, dents and
damages.
If bolts or nuts are loose, tighten them to specification.

Check nearby body areas for damaged, missing, or misposi-
tioned parts, open seams, holes, loose connections or other de-
fects which could permit exhaust fumes to seep into the vehicle.

Make sure that exhaust system components have enough clear-
ance from the underbody to avoid overheating and possible dam-
age to the floor carpet.

Any defects should be fixed at once.

YH4
GRAND
VITARA
0B-12 MAINTENANCE AND LUBRICATION
IGNITION SYSTEM
ITEM 2-1
Spark Plugs Replacement
Replace spark plugs with new ones referring to Section 6F1 or 6F2.
FUEL SYSTEM
ITEM 3-1
Air Cleaner Filter
Inspection
1) Remove air cleaner case clamps.
2) Take cleaner filter out of air cleaner case.
3) Check air cleaner filter for dirt. Replace excessively dirty filter.
4) Blow off dust by compressed air from air outlet side of filter.
5) Install air cleaner filter into case.
6) Install air cleaner case cap and clamp it securely.
Replacement
Replace air cleaner filter with new one according to above steps 1),
2) and 5), 6).
ITEM 3-2
Fuel Lines and Connections Inspection
1) Visually inspect fuel lines and connections for evidence of fuel
leakage, hose cracking and damage. Make sure all clamps are
secure.
Repair leaky joints, if any.
Replace hoses that are suspected of being cracked.