system SUZUKI GRAND VITARA 2000 2.G Service Workshop Manual

YH4
GRAND
VITARA
1. Inner end of interlock cable
2. Key release cam
1. Key release cam
2. Cable outer(a)
Type-2
Type-2
AUTOMATIC TRANSMISSION (4 A / T) 7B1-73
TYPE-2
5) With key release cam set as shown at the left figure, connect
inner end of interlock cable to key release cam. (Select lever
side.)
6) Move key release cam so that it is set at such angle as shown
at the left figure and with special tool inserted in hole A , fix key
release cam.
Special Tool
(A): 09925-78210 (6 mm)
7) With key release cam fixed with special tool, install cable outer
to bracket and after making sure that cable outer is pushed in
arrow direction B by leaf spring, tighten mounting nut to speci-
fied torque. Remove special tool.
Tightening Torque
(a): 13 N
.m (1.3 kg-m, 9.5 lb-ft)
8) Turn ignition key to ªACCº position and shift select lever to ªNº
range, and check for the followings.
a. When select lever is shifted at ªPº range with knob button
depressed, ignition key can not be turned from ªACCº to
ªLOCKº position.
b. When knob button is released, ignition key can be turned to
ªLOCKº position.
c. When ignition key is at ªLOCKº position, select lever can not
be shifted from ªPº to any other range.
9) Install console box.
10) Install steering column cover.
11) Adjust steering column or tighten steering column bolts.
12) Install steering column hole cover.
13) If equipped with air bag system, enable air bag system.
Refer to ªEnabling Air bag Systemº in Section 10B.

YH4
GRAND
VITARA
1. Pipe
2. Hose
3. Flare nut
1. Pipe
2. Hose
3. Flare nut
4. E-ring
1. Master cylinder
assembly
2. Clutch pipe
3. Attaching nut
4. Attaching bolt
5. Clevis pin
6. Clip
7. Flare nut
CLUTCH 7C1-5
INSPECTION
Check pipe and hose for dent, kink, crack, dirt and dust. Replace
if check result is not satisfactory.
INSTALLATION
Reverse removal sequence noting following points.
Tighten flare nuts to specified torque.
Tightening Torque
(a): 16 N
.m (1.6 kg-m, 11.5 lb-ft)
NOTE:

For air bleeding of master cylinder alone, it must be removed
from vehicle.
(For procedures of removal and installation of master cylin-
der assembly and air bleeding, refer to CLUTCH MASTER
CYLINDER section.)

Do not allow fluid to get on painted surface.

Do not allow pipe and hose to contact hard against vehicle
or other parts.

Install each clamp securely.

Install E-ring securely as shown.

After installation, check clutch pedal free travel and bleed air
from system.

Check fluid leakage.

Add fluid close to MAX level of reservoir.
CLUTCH MASTER CYLINDER
REMOVAL
1) Clean around reservoir cap and take out fluid with syringe or
such.
2) Remove push rod clevis pin.
3) Disconnect fluid pipe from master cylinder.
NOTE:
Do not allow fluid to get on painted surfaces.
4) Remove master cylinder attaching nut and bolt.
5) Remove master cylinder assembly and gasket.

YH4
GRAND
VITARA
1. Master cylinder
1. Attaching bolt
2. Attaching nut
3. Clevis pin
ªAº
7C1-6 CLUTCH
INSTALLATION
1) To bleed air from master cylinder itself, tilt it as shown in figure
and add fluid into it.
NOTE:
After bleeding air from master cylinder, plug pipe hole in it
to prevent fluid from spilling out of it till pipe is connected.
2) Install master cylinder assembly and new gasket to body, attach-
ing bolt, nuts and push rod clevis pin.
NOTE:
Do not reuse gasket.
3) Torque attaching bolt and nut to specification.
4) Connect fluid pipe and torque flare nut to specification.
Tightening Torque
(a): 13 N
.m (1.3 kg-m, 9.5 lb-ft)
(b): 16 N
.m (1.6 kg-m, 11.5 lb-ft)
5) Apply grease to clevis pin and install it.
ªAº: Grease 99000-25010
6) Fill reservoir with specified brake fluid and check fluid leakage.
7) After installation, bleed air from system and check clutch pedal
free travel. Refer to BRAKE section for air bleeding procedure.
FLUID INSPECTION
Fluid level should be always between MIN and MAX lines on reser-
voir. If fluid decreases quickly, check for leakage, repair leaky point,
if any, and add fluid up to MAX level.
NOTE:

Brake fluid damages painted surface badly. Should it get on
painted surface, remove it immediately and clean surface
thoroughly.

Do not use shock absorber fluid or any other fluid which con-
tains mineral oil. Do not use container which has been used
for mineral oil or which is wet from water. Mineral oil will
cause swelling and distortion of rubber parts in hydraulic
clutch system and water will mix with brake fluid, lowering
fluid boiling point. Keep all fluid containers capped to pre-
vent contamination.

Make sure not to use fluid whose container cap was first
opened more than a year ago.

YH4
GRAND
VITARA
CLUTCH 7C1-9
5) Fill reservoir with specified brake fluid and check for fluid leak-
age.
6) Bleed air from system and check clutch pedal free travel. Refer
to BRAKE section for air bleeding procedure.

YH4
GRAND
VITARA
TRANSFER 7D-7
09940-53111
Bearing installer
UNIT REPAIR
Refer to the same section of UNIT REPAIR MANUAL mentioned in FOREWORD of this manual.
TIGHTENING TORQUE SPECIFICATIONS
FasteningportionTightening torqueFastening ortionN.mkg-mlb-ft
Oil filler / level and drain plugs232.317.0
Engine rear mounting bolts505.036.5
Universal joint flange bolts505.036.5
Speed sensor bolt60.64.5
REQUIRED SERVICE MATERIALS
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
Lithium greaseSUZUKI SUPER GREASE A
(99000-25010)

Oil seal lips and O-rings.

Splines of propeller shaft.

Select return system.

Shift control lever.
SPECIAL TOOL

YH4
GRAND
VITARA
7E
DIFFERENTIAL (FRONT) 7E-1
The differential assembly using a hypoid bevel pinion
and gear is installed to the front axle.
4WD control system controls drive force to be trans-
mitted to front axles or not. The reduction ratio varies
depending on transmission or engine type.The differential assembly is decisive in that the drive
power is concentrated there. Therefore, use of genu-
ine parts and specified torque is compulsory. Further,
because of sliding tooth meshing with high pressure
between bevel pinion and gear, it is mandatory to lu-
bricate them by hypoid gear oil.
SECTION 7E
DIFFERENTIAL (FRONT)
CONTENTS
GENERAL DESCRIPTION7E- 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4WD CONTROL SYSTEM7E- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS7E- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS TABLE7E- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential Assembly7E- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4WD Control System Diagnostic Flow Table 7E- 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4WD CONTROL CIRCUIT INSPECTION 7E- 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7E- 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE SERVICE7E- 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gear Oil Change7E- 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSPECTION7E-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4WD Control System7E-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Actuator7E-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air Pump Assembly7E-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION 7E-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential Mountings7E-13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DISMOUNTING7E-15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOUNTING7E-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7E-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS7E-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIAL7E-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS7E-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION

YH4
GRAND
VITARA
1. 4WD switch
2. Transfer
3. Blank
4. Blank
5. ECM or PCM
6. Glove box7. Air pump assembly
8. Actuator
9. Axle lock clutch
10. Free axle hub
11. 4WD indicator lamp
7E-2 DIFFERENTIAL (FRONT)
4WD CONTROL SYSTEM
When the 4WD switch is turned ON by shifting the transfer shift lever, ECM (PCM) (G16 and J20 engine models)
or 4WD controller (H25 engine model) actuates (energizes) the air pump assembly. Then positive pressure is sent
from the air pump assembly to the actuator installed to the differential case and causes the axle lock clutch and
the free axle hub in the differential case to be engaged, resulting in the 4WD mode. Only when running in the 4WD
mode, front axles are joined to differential case, and they become free when 2WD mode is used (or when transfer
shift lever is shifted to N position), thereby reducing the power loss.

YH4
GRAND
VITARA
1. 4WD switch
2. Air pump assembly
3. Pump motor
4. Release valve
5. Pressure switch6. Transfer
7. Front differential
8. Air hose and pipe
9. 4WD indicator lamp
10. To ignition switch
11. ECM or PCM
Operation
(refer to ªComponents and Functionsº)
Power supply
(from ECM or PCM)
DIFFERENTIAL (FRONT) 7E-3
System Circuit and Operation

YH4
GRAND
VITARA
7E-4 DIFFERENTIAL (FRONT)
Components and Functions
ComponentFunction
4WD switch
When the transfer shift lever is shifted to 4L or 4H position, this switch turns ON
and causes the 4WD control system to turn ON, unless it is shifted to N or 2H
within 1 second.
ECM or PCM
When the 4WD switch turns ON [unless it turns OFF within 1 second], this com-
ponent actuates the pump assembly. If the pressure in the air pump assembly
fails to increase higher than the set level even after the pump motor has run more
than 10 seconds, this component stops the motor to protect it.
Air pump assembly

Pump motor

Release valve

Pressure switchThe air pump assembly consists of a pump motor, release valve and a pressure
switch.
Pump motor:
Produces positive pressure which actuates the actuator.
Release valve:
Closes when transfer shift lever is shifted to 4H or 4L so that the positive pressure
is applied to the actuator, and opens when N or 2H to release the pressure to the
atmosphere.
Pressure switch:
Turns ON and OFF depending on the pressure level in the pump assembly
(whether higher or lower than the set pressure level). ECM or PCM detects the
pressure level through this switch.
Differential case assembly

Free axle hub

Axle lock clutch

ActuatorThe free axle hub, axle lock clutch and actuator are installed in the differential
left case. The positive pressure produced in the air pump assembly is applied
to the actuator which then pushes the axle lock clutch to be engaged with the free
axle hub. In this state, the drive force is transmitted to the front axle, resulting in
the 4WD mode.
When the actuator is free from the positive pressure [when it is under the atmo-
spheric pressure], the axle lock clutch is pushed back by the return spring force
and cannot be engaged with the free axle hub, resulting in the 2WD mode.
ª4WDº indicator lampIt lights up when 4WD control system is in the 4WD mode.

YH4
GRAND
VITARA
DIFFERENTIAL (FRONT) 7E-5
DIAGNOSIS
DIAGNOSIS TABLE
Differential Assembly
ConditionPossible CauseCorrection
Gear noise
Deteriorated or water mixed lubricant

Inadequate or insufficient lubricant

Maladjusted backlash between bevel
pinion and gear

Improper tooth contact in the mesh between
bevel pinion and gear

Loose bevel gear securing bolts

Damaged side gear(s) or side pinion(s)Repair and replenish
Repair and replenish
Adjust
Adjust or replace
Replace or retighten
Replace
Bearing noise
(Constant noise) Deteriorated or water
mixed lubricant

(Constant noise) Inadequate or insufficient
lubricant

(Noise while coasting) Damaged bearing(s)
of bevel pinion

(Noise while turning) Damaged diff. side
bearing(s) or axle bearing(s)Repair and replenish
Repair and replenish
Replace
Replace
Oil leakage
Worn or damaged oil seal

Excessive oil

Loose differential carrier boltsReplace
Adjust oil level
Replace or retighten
2WD / 4WD
switching error
Defective actuator

Abnormality in 4WD control systemReplace
Inspect referring to ª4WD
CONTROL SYSTEM DIAG-
NOSTIC FLOW TABLEº.
4WD Control System Diagnostic Flow Table
Before performing the trouble diagnosis, check that the transfer and front differential are in good condition and
there is no air leakage from air hoses and the actuator. Refer to ªON-VEHICLE SERVICEº in this section for air
leakage.
[NOTES ON SYSTEM CIRCUIT INSPECTION]

Be sure to read ªPrecautions for Electrical Circuit Serviceº in Section 0A before circuit inspection and observe
what is written there.

For system circuit, refer to the figure of ªGENERAL DESCRIPTIONº in this section.

For terminal arrangement, refer to ª4WD Control Circuit Inspectionº in this section.