Rf 2.0 SUZUKI GRAND VITARA 2000 2.G Service Owner's Manual

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-55
Check resultPossible cause
Line pressure higher
than standard level in
each range
Malfunctioning regulator valve

Malfunctioning throttle valve

Maladjusted A / T throttle cable
Line pressure lower than
standard level in each
range
Defective O/D clutch

Defective oil pump

Malfunctioning throttle valve

Malfunctioning regulator value

Maladjusted A / T throttle cable
Line pressure lower than
standard level only in ªDº
range
Fluid leakage from forward clutch

Defective O/D clutch

Leakage from ªDº range fluid pressure cir-
cuit
Line pressure lower than
standard level only in ªRº
range
Fluid leakage from direct clutch

Defective O/D clutch

Fluid leakage from reverse brake

Fluid leakage from ªRº range fluid circuit
Tightening torque of transmission case plug:
17 N.m (1.7 kg-m, 12.0 lb-ft)
STALL TEST
This test is to check overall performance of automatic transmission
and engine by measuring stall speed at ªDº and ªRº ranges. Be sure
to perform this test only when transmission fluid is at normal operat-
ing temperature and its level is between FULL and LOW marks.
CAUTION:

Do not run engine at stall more than 5 seconds continu-
ously, for fluid temperature may rise excessively high.

After performing stall test, be sure to leave engine running
at idle for longer than 30 seconds before another stall test.
1) Apply parking brake and block wheels.
2) Install tachometer.
3) Start engine with select lever shifted to ªPº.
4) Depress brake pedal fully.
5) Shift select lever to ªDº and depress accelerator pedal fully while
watching tachometer. Read engine rpm quickly when it has be-
come constant (stall speed).
6) Release accelerator pedal immediately after stall speed is
checked.
7) In the same way, check stall speed in ªRº range.

YH4
GRAND
VITARA
DIFFERENTIAL (FRONT) 7E-11
1. Differential housing
2. Adjusting screw
3. To air compressor
Actuator
1) Disconnect air hose from pump assembly and install special tool
to air hose as shown in figure. Loosen adjusting screw of special
tool.
Special Tool
(A): 09918-18110
2) Connect compressor air hose to special tool.
Blow air and turn adjusting screw to obtain specified pressure.
Specified pressure: 30.0 kPa (0.3 kg / cm
2, 4.25 psi)
CAUTION:
Do not apply a pressure exceeding 200 kPa (2.0 kg / cm
2,
28.4 psi) which may cause damage to diaphragm.
3) With the vehicle lifted so that both of the front wheels are off the
ground, turn one of the front wheels by hand and check the other
wheel, which should act as described below.

When the pressure from compressor is applied to actuator:
The other front wheel should turn in the direction opposite to
the wheel being turned by hand.

When the pressure from compressor is not applied to actuator:
The other front wheel should remain stationary while the wheel
pushed by hand is turning.
If the result is not satisfactory, inspect differential assembly. Re-
fer to ªINSPECTIONº of SECTION 7E in UNIT REPAIR MANU-
AL.

YH4
GRAND
VITARA
INSTRUMENTATION / DRIVER INFORMATION 8C-9
1. Exhaust pipe
FUEL METER / FUEL GAUGE UNIT
FUEL METER
INSPECTION
1) Remove rear bumper facing.
2) Detach grommet (3) from vehicle.
3) Disconnect coupler (2) of fuel pump and gauge.
4) Turning switch ON, and check that fuel meter indicates E.
5) Turn ignition switch OFF.
6) Ground Bl / W lead through a 3.4 W test bulb (4) as illustrated.
7) Turn ignition switch ON and check that bulb light up and pointer
(5) moves to F side.
8) If fuel meter shows no operation, repair or replace defective
parts.
FUEL SENDER GAUGE
INSPECTION
1) Remove fuel pump assembly (1) referring to FUEL PUMP RE-
MOVAL in Section 6C.
2) Check resistance between terminals (A) and (B) under each
float position.
Float Position
FuelResistance (
)56
model66
modelMeterResistance (
)
ªaº88.3 mm
(3.48 in.)51.7 mm
(2.04 in.)F6 ± 8
ªbº157.2 mm
(6.20 in.)139.6 mm
(5.50 in.)1/229.5 ± 35.5
ªcº254.9 mm
(10.0 in.)254.9 mm
(10.0 in.)E94 ± 96
If measured valve is out of specification, replace fuel sender gauge.