Led SUZUKI GRAND VITARA 2000 2.G Service Workshop Manual

YH4
GRAND
VITARA
ªAº
0A-8 GENERAL INFORMATION

When removing the battery, be sure to disconnect the nega-
tive cable first and then the positive cable. When reconnect-
ing the battery, connect the positive cable first and then the
negative cable, and replace the terminal cover.

When removing parts that are to be reused, be sure to keep
them arranged in an orderly manner so that they may be rein-
stalled in the proper order and position.

Whenever you use oil seals, gaskets, packing, O-rings, lock-
ing washers, split pins, self-locking nuts, and certain other
parts as specified, be sure to use new ones. Also, before
installing new gaskets, packing, etc., be sure to remove any
residual material from the mating surfaces.

Make sure that all parts used in reassembly are perfectly
clean.

When use of a certain type of lubricant, bond or sealant is
specified, be sure to use the specified type.
ªAº: Sealant 99000-31150

Be sure to use special tools when instructed.
Special Tool
(A): 09917-98221
(B): 09916-58210

YH4
GRAND
VITARA
GENERAL INFORMATION 0A-9

When disconnecting vacuum hoses, attach a tag describing
the correct installation positions so that the hoses can be re-
installed correctly.

After servicing fuel, oil, coolant, vacuum, exhaust or brake
systems, check all lines related to the system for leaks.

For vehicles equipped with fuel injection systems, never dis-
connect the fuel line between the fuel pump and injector
without first releasing the fuel pressure, or fuel can be
sprayed out under pressure.
PRECAUTIONS FOR CATALYTIC CONVERTER
For vehicles equipped with a catalytic converter, use only un-
leaded gasoline and be careful not to let a large amount of un-
burned gasoline enter the converter or it can be damaged.
± Conduct a spark jump test only when necessary, make it as
short as possible, and do not open the throttle.
± Conduct engine compression checks within the shortest
possible time.
± Avoid situations which can result in engine misfire (e.g.
starting the engine when the fuel tank is nearly empty).

YH4
GRAND
VITARA
0A-14 GENERAL INFORMATION
To other
parts
Other parts
To other
partsSHORT CIRCUIT CHECK (Wire harness to ground)
1) Disconnect negative cable from battery.
2) Disconnect connectors at both ends of the circuit to be checked.
NOTE:
If the circuit to be checked is connected to other parts, dis-
connect all connectors of those parts.
Otherwise, diagnosis will be misled.
3) Measure resistance between terminal at one end of circuit (A-1
terminal in figure) and body ground. If continuity is indicated, it
means that there is a short to ground between terminals A-1 and
C-1 of the circuit.
4) Disconnect the connector included in circuit (connector B) and
measure resistance between A-1 and body ground.
If continuity is indicated, it means that the circuit is shorted to the
ground between terminals A-1 and B-1.

YH4
GRAND
VITARA
0B-2 MAINTENANCE AND LUBRICATION
MAINTENANCE SCHEDULE
MAINTENANCE SCHEDULE UNDER NORMAL DRIVING CONDITIONS
Interval:
This interval should be judged by
This table includes services as scheduled up to 90,000 km
(54,000 miles) mileage. Beyond 90,000 km (54,000 miles), carry
out the same services at the same intervals respectively.
This interval should be judged by
odometer reading or months,Km (x 1,000)153045607590g
whichever comes first.Miles (x 1,000)91827364554
Months122436486072
ENGINE
1-1. Drive beltV-beltIRIRIR
V-rib belt (Flat type)±±I±±R
1-2. Camshaft timing belt (G16 engine only)Replace every 100,000 km or
60,000 miles
1-3. Valve lash (clearance)G16 engine only±I±I±I
1-4. Engine oil and
oil filterJ20 / H25 engines
G16 engine with HO2S (SG, SH, SJ)RRRRRR
G16 engine with HO2S (SE, SF),
G16 engine without HO2SReplace every 10,000 km (6,000 miles)
or 8 months
1-5. Engine coolant±±R±±R
1-6. Exhaust system±I±I±I
IGNITION SYSTEM
2-1. Spark plugs
Wh
Vehicle without
HO2S
Nickel plug±R±R±R
When
unleaded
HO2SIridium plug±±±R±±unleaded
fuel isVehicle with
HO2S
Nickel plug±±R±±Rfuel is
usedHO2SIridium plugReplace every 105,000 km or 63,000
miles
When leaded fuel is used, refer to ªSevere Driving Conditionº schedule
FUEL SYSTEM
3-1. Air cleaner filterIIRIIR
3-2. Fuel lines and connections±I±I±I
3-3. Fuel filterReplace every 105,000 km or 63,000
miles
3-4. Fuel tank±±I±±I
EMISSION CONTROL SYSTEM
4-1. Crankcase ventilation hoses and connections
(Vehicle without HO2S)±±I±±I
4-2. PCV valveVehicle without HO2S±±I±±I
Vehicle with HO2S±±±±±I
4-3. Fuel evaporative emission
tl t
Vehicle without HO2S±I±I±I
control systemVehicle with HO2S±±±±±I
NOTES:

ªRº : Replace or change

ªIº : Inspect and correct, replace or lubricate if necessary

For Item 1-2. Camshaft timing belt: This belt may be replaced every 90,000 km (54,000 miles) according
to customer's maintenance convenience.

For Sweden, item 2-1, 4-2 and 4-3 should be performed by odometer reading only.

For Item 2-1. Spark plugs, replace every 50,000 km if the local law requires.

Nickel spark plug: BKR6E-11 or K20PR-U11

Iridium spark plug: IFR6E11 or SK20PR-A11 for G16 engine, IFR5J11 or SK16PR11 for J20 / H25 engines

YH4
GRAND
VITARA
MAINTENANCE AND LUBRICATION 0B-3
Interval:
This interval should be
judged by
This table includes services as scheduled up to 90,000 km
(54,000 miles) mileage. Beyond 90,000 km (54,000 miles), carry
out the same services at the same intervals respectively.
This interval should be judged by
odometer reading or months,Km (x 1,000)153045607590g
whichever comes first.Miles (x 1,000)91827364554
Months122436486072
CHASSIS AND BODY
6-1. Clutch (pedal and fluid level)±I±I±I
6-2.Brake discs and pads (thickness, wear, damage)IIIIII
Brake drums and shoes (wear, damage) ±I±I±I
6-3. Brake hoses and pipes (leakage, damage, clamp)±I±I±I
6-4. Brake fluid±R±R±R
6-5. Brake lever and cable (damage, stroke, operation)Inspect at first 15,000 km (9,000 miles)
only
6-6. Tires (wear, damage, rotation)IIIIII
6-7. Wheel discs (damage)IIIIII
6-8. Suspension system (tighteness, damage, rattle, breakage)±I±I±I
6-9. Propeller shafts and drive shafts±±I±±I
6-10. Manual transmission oil (leakage, level)
(I: 1st 15,000 km only)I±R±±R
6-11. Automatic transmissionFluid level±I±I±I
Fluid changeReplace every 165,000 km
(99,000 miles)
Fluid hose±±±R±±
6-12. Transfer oil (leakage, level)I±I±I±
6-13. Differential oil (leakage, level) (R: 1st 15,000 km only)R or I±I±I±
6-14. Steering system (tighteness, damage, breakage, rattle)±I±I±I
6-15. Power steering (if equipped)IIIIII
6-16. All latches, hinges and locks±I±I±I
6-17. Air conditioning filter (if equipped)±IR±IR
NOTES:
ªRº : Replace or change
ªIº : Inspect and correct, replace or lubricate if necessary

YH4
GRAND
VITARA
1
1. Clutch pedal free travel
MAINTENANCE AND LUBRICATION 0B-15
CHASSIS AND BODY
ITEM 6-1
Clutch
Pedal inspection
Check clutch pedal for height and free travel referring to Section
7C1. Adjust or correct if necessary.
Fluid inspection
1) Check around master cylinder and reservoir for fluid leakage.
If found leaky, correct.
2) Check fluid level.
If fluid level is lower than the minimum level of reservoir, refilling
is necessary. Fill reservoir with specified brake fluid indicated on
clutch reservoir cap.
For the details, refer to On-vehicle service in Section 7C1.
CAUTION:
Since clutch system of this vehicle is factory-filled with
glycol-base brake fluid, do not use or mix different type
of fluid when refilling system; otherwise serious damage
will occur. Do not use old or used brake fluid, or one taken
from unsealed container.
ITEM 6-2
Brake Discs, Pads, Brake Drums and Shoes Inspection
[Brake discs and pads]
1) Remove wheel and caliper but don't disconnect brake hose from
caliper.
2) Check front disc brake pads and discs for excessive wear, dam-
age and deflection. Replace parts as necessary. For details, re-
fer to Section 5B.
Be sure to torque caliper pin bolts to specification.
[Brake drums and shoes]
1) Remove wheel and brake drum.
2) Check rear brake drums and brake linings for excessive wear
and damage, while wheels and drums are removed. At the same
time, check wheel cylinders for leaks. Replace these parts as
necessary.
For details, refer to Section 5C.

YH4
GRAND
VITARA
0B-18 MAINTENANCE AND LUBRICATION
ITEM 6-8
Suspension System Inspection
Check suspension bolts and nuts for tightness and retighten them
as necessary.
Repair or replace defective parts, if any.
NOTE:
For details of check points, refer to tables of Tightening Torque
Specification in Section 3D and 3E.
Front
1) Check stabilizer bar for damage or deformation.
2) Check bushing for damage, wear or deterioration.
3) Inspect strut for damage, deformation, oil leakage and opera-
tion. If strut is found faulty, replace it as an assembly unit, be-
cause it can not be disassembled.
Refer to strut check Section 3D for operation check.
4) Inspect strut boot for damage or crack.
5) Inspect for cracks or deformation in spring seat.
6) Inspect for deterioration of bump stopper.
7) Inspect strut mount for wear, cracks or deformation.
8) Check ball joint stud dust seal (boot) for leaks, detachment,
tear or other damage. Check suspension arm bushing for dam-
age, wear or deterioration.
Rear
9) Check shock absorber for damage, deformation, oil leakage
and operation.
10) Check bushings for wear and damage.

YH4
GRAND
VITARA
1. Drain plug (Apply sealant)
2. Reverse idle gear shaft bolt (DO NOT LOOSEN IT)
3. Filler / level plug (Apply sealant)
1. Drain plug
2. Filler / level plug
Type 1
Type 2
1. Level gauge
2. FULL HOT mark
3. LOW HOT mark
4. FULL COLD mark
5. LOW COLD mark
0B-20 MAINTENANCE AND LUBRICATION
ITEM 6-10
Manual Transmission Oil Inspection and Change
Inspection
1) Inspect transmission case for evidence of oil leakage.
Repair leaky point if any.
2) Make sure that vehicle is placed level for oil level check.
3) Remove level plug of transmission.
4) Check oil level.
Oil level can be checked roughly by means of level plug hole.
That is, if oil flows out of level plug hole or if oil level is found up
to hole when level plug is removed, oil is properly filled.
If oil is found insufficient, pour specified amount of specified oil.
5) Tighten level plug to specified torque.
Refer to Section 7A or 7A1 for installation and tightening torque.
Change
Change transmission oil with new specified oil referring to Section
7A or 7A1.
ITEM 6-11
Automatic Transmission Fluid Inspection and Change
Inspection
1) Inspect transmission case for evidence of fluid leakage.
Repair leaky point, if any.
2) Make sure that vehicle is placed level for fluid level check.
3) Check fluid level.
For fluid level checking procedure, refer to On-vehicle service in
Section 7B1 and be sure to perform it under specified conditions.
If fluid level is low, replenish specified fluid.

YH4
GRAND
VITARA
1. Drain plug
Transfer
Front differential
Rear differential
1
21
2
MAINTENANCE AND LUBRICATION 0B-21
Change
1) Inspect transmission case for evidence of fluid leakage.
Repair leaky point, if any.
2) Make sure that vehicle is placed level for fluid level check.
3) Change fluid. For its procedure, refer to On-vehicle service in
Section 7B1.
Fluid cooler hose change
Replace inlet and outlet hoses of cooler hose and their clamps.
For replacement procedure, refer to On-vehicle service in Section
7B1.
ITEM 6-12 and 6-13
Transfer and Differential Oil Inspection and Change
Inspection
1) Check transfer case and differential for evidence of oil leakage.
Repair leaky point if any.
2) Make sure that vehicle is placed level for oil level check.
3) Remove level plug of transfer or differentials (front and rear) and
check oil level.
Oil level can be checked roughly by means of level plug hole.
That is, if oil flows out of level plug hole or if oil level is found up
to hole when level plug is removed, oil is properly filled.
If oil is found insufficient, pour specified amount of specified oil
referring to Section 7D, 7B or 7F.
4) Tighten level plug to specified torque.
Refer to Section 7D, 7E or 7F for tightening torque.
Change
Change transfer oil or differentials oil with new specified oil referring
to Section 7D, 7E and 7F respectively.

YH4
GRAND
VITARA
0B-24 MAINTENANCE AND LUBRICATION
FINAL INSPECTION
Seats
Check that seat slides smoothly and locks securely at
any position. Also check that reclining mechanism of
front seat back allows it to be locked at any angle.
Seat Belt
Inspect belt system including webbing, buckles, latch
plates, retractors and anchors for damage or wear.
If ªREPLACE BELTº label on front seat belt is visible,
replace belt.
Check that seat belt is securely locked.
Battery Electrolyte Level Check
Check that the electrolyte level of all battery cells is
between the upper and lower level lines on the case.
If battery is equipped with built-in indicator, check bat-
tery condition by the indicator.
Accelerator Pedal Operation
Check that pedal operates smoothly without getting
caught or interfered by and other part.
Engine Start
Check engine start for readiness.
On automatic transmission vehicles, try to start the
engine in each select lever position. The starting mo-
tor should crank only in ªPº (Park) or ªNº (Neutral).
On manual transmission vehicles, place the shift le-
ver in ªNeutral,º depress clutch pedal fully and try to
start.
Exhaust System Check
Check for leakage, cracks or loose supports.
Clutch (For Manual transmission)
Check for the following:

Clutch is completely released when depressing
clutch pedal.

No slipping clutch occurs when releasing pedal and
accelerating.

Clutch itself is free from any abnormal condition.
Gearshift or Select Lever (Transmission)
Check gear shift or select lever for smooth shifting to
all positions and for good performance of transmis-
sion in any position.
With automatic transmission equipped vehicle, also
check that shift indicator indicates properly according
to which position select lever is shifted to.
With automatic transmission equipped vehicle, make
sure that vehicle is at complete stop when shifting se-
lect lever to ªPº range position and release all brakes.
Brake
[Foot brake]
Check the following:

that brake pedal has proper travel,

that brake works properly,

that it is free from noise,

that braking force is applied equally on all wheels,

and that brake do not drag.
[Parking brake]
Check that lever has proper travel.
WARNING:
With vehicle parked on a fairly steep slope,
make sure nothing is in the way downhill to
avoid any personal injury or property damage.
Be prepared to apply regular brake quickly
even if vehicle should start to move.
Check to ensure that parking brake is fully effective
when the vehicle is stopped on the safe slope and
brake lever is pulled all the way.
WARNING:
When carrying out road tests, select a safe
place where no man or no running vehicle is
seen so as to prevent any accident.
WARNING:
Before performing the following check, be
sure to have enough room around the vehicle.
Then, firmly apply both the parking brake and
the regular brakes. Do not use the accelerator
pedal. If the engine starts, be ready to turn off
the ignition promptly. Take these precautions
because the vehicle could move without warn-
ing and possibly cause personal injury or
property damage.