load SUZUKI GRAND VITARA 2000 2.G Service Workshop Manual

YH4
GRAND
VITARA
L
LH : Left Hand
LSPV : Load Sensing Proportioning
Valve
M
MAF Sensor : Mass Air Flow Sensor
(Air Flow Sensor, AFS, Air
Flow Meter, AFM)
MAP Sensor : Manifold Absolute Pressure
Sensor (Pressure Sensor, PS)
Max : Maximum
MFI : Multiport Fuel Injection
(Multipoint Fuel Injection)
Min : Minimum
MIL : Malfunction Indicator Lamp
(ªCHECK ENGINEº Light)
M / T : Manual Transmission
N
NOx : Nitrogen Oxides
O
OBD : On-Board Diagnostic System
(Self-Diagnosis Function)
O / D : Overdrive
OHC : Over Head Camshaft
P
PNP : Park / Neutral Position
P / S : Power Steering
PSP Switch : Power Steering Pressure
Switch (P / S Pressure Switch)
PCM : Powertrain Control Module
PCV : Positive Crankcase Ventilation
R
RH : Right Hand
S
SAE : Society of Automotive
Engineers
SDM : Sensing and Diagnostic
Module (Air bag controller,
Air bag control module)
SFI : Sequential Multiport Fuel
Injection
SOHC : Single Over Head Camshaft
T
TBI : Throttle Body Fuel Injection
(Single-Point Fuel Injection,
SPI)
TCC : Torque Converter Clutch
TCM : Transmission Control Module
(A / T Controller, A / T Control
Module)
TP Sensor : Throttle Position Sensor
TVV : Thermal Vacuum Valve
(Thermal Vacuum Switching
Valve, TVSV, Bimetal Vacuum
Switching Valve, BVSV)
TWC : Three Way Catalytic
Converter (Three Way
Catalyst)
2WD : 2 Wheel Drive
V
VIN : Vehicle Identification
Number
VSS : Vehicle Speed Sensor
W
WU-OC : Warm Up Oxidation
Catalytic Converter
WU-TWC : Warm Up Three Way
Catalytic Converter
0A-22 GENERAL INFORMATION

YH4
GRAND
VITARA
3-2 STEERING, SUSPENSION, WHEELS AND TIRES
ConditionPossible CauseCorrection
Abnormal or
Excessive Tire Wear
Sagging or broken springs.

Tire out of balance.

Disturbed front end alignment.

Faulty shock absorber.

Hard driving.

Overloaded vehicle.

Tires not rotating.

Worn or loose road wheel bearings.

Wobbly wheel or tires.

Tires not adequately inflated.Replace spring.
Adjust balance or replace tire.
Check front end alignment.
Replace shock absorber.
Replace tire.
Replace tire.
Replace or rotate tire.
Replace wheel bearing.
Replace wheel or tire.
Adjust the pressure.
Wheel Tramp
Blister or bump on tire.

Improper shock absorber action.Replace tire.
Replace shock absorber.
Shimmy, Shake or
Vibration
Tire or wheel out of balance.

Loose wheel bearings.

Worn tie rod ends.

Worn lower ball joints.

Excessive wheel runout.

Blister or bump on tire.

Excessively loaded radial runout of
tire / wheel assembly.

Disturbed front end alignment.

Loose or worn tie-rod end.

Loose steering gear case bolts.Balance wheels or replace tire and /
or wheel.
Replace wheel bearing.
Replace tie rod end.
Replace front suspension control
arm.
Repair or replace wheel and / or tire.
Replace tire.
Replace tire or wheel.
Check front end alignment.
Tighten or replace tie-rod end.
Tighten case bolts.
Hard Steering
Bind in tie rod end ball studs or
lower ball joints.

Disturbed front end alignment.

Rack and pinion not properly adjusted.
(if equipped with manual steering gear
case)

Tire not adequately inflated.

Bind in steering column.

Low fluid level, loose drive belt or
malfunction of power steering system.
(if equipped with P / S)Replace tie rod end or front
suspension control arm.
Check front end alignment.
Check and adjust steering gear box.
Inflate tires to proper pressure.
Repair or replace.
Check and correct.

YH4
GRAND
VITARA
3-4 STEERING, SUSPENSION, WHEELS AND TIRES
ConditionPossible CauseCorrection
Wander or Poor
Steering Stability
Mismatched or uneven tires.

Loose ball joints and tie rod
ends.

Faulty shock absorbers / struts or
mounting.

Loose stabilizer bar.

Broken or sagging springs.

Rack and pinion not properly adjusted.
(if equipped with manual steering
gear case)

Disturbed front end alignment.Replace tire or inflate tires to
proper pressure.
Replace suspension control arm or
tie rod end.
Replace absorber / strut or repair
mounting.
Tighten or replace stabilizer bar or
bushes.
Replace spring.
Check or adjust rack and pinion
torque.
Check and adjust front end alignment.
Erratic Steering when
Braking
Worn wheel bearings.

Broken or sagging springs.

Leaking wheel cylinder or caliper.

Warped discs.

Badly worn brake linings.

Drum is out of round in some brakes.

Wheel tires are inflated unequally.

Defective wheel cylinders.

Disturbed front end alignment.Replace wheel bearing.
Replace spring.
Repair or replace wheel cylinder or
caliper.
Replace brake disc.
Replace brake shoe lining.
Replace brake drum.
Inflate tires to proper pressure.
Replace or repair wheel cylinder.
Check front end alignment.
Low or Uneven Trim
Height
Right-to-left trim height
(H) difference should be
within 15 mm (0.6 in.)
with curb weight.
*Same with rear side.
Broken or sagging springs.

Overloaded.

Incorrect springs.Replace spring.
Check loading.
Replace spring.
Ride Too Soft
Faulty shock absorber or struts.Replace shock absorber or strut.
Suspension Bottoms
Overloaded.

Faulty shocks or struts.

Incorrect broken or sagging springs.Check loading.
Replace shock absorber or strut.
Replace spring.

YH4
GRAND
VITARA
STEERING, SUSPENSION, WHEELS AND TIRES 3-5
ConditionPossible CauseCorrection
Body Leans or Sways
in Corners
Loose stabilizer bar.

Faulty shock absorbers, struts
or mounting.

Broken or sagging springs.

Overloaded.Tighten stabilizer bar bolts or
replace bushes.
Replace shock absorber, strut or
tighten mounting.
Replace spring.
Check loading.
Cupped Tires
Front struts defective.

Worn wheel bearings.

Excessive tire or wheel run-out.

Worn ball joints.

Tire out of balance.Replace strut.
Replace wheel bearing.
Replace tire or wheel disc.
Replace front suspension control
arm.
Adjust tire balance.

YH4
GRAND
VITARA
3-8 STEERING, SUSPENSION, WHEELS AND TIRES
RADIAL TIRE LEAD
ªLeadº is the deviation of the vehicle from a straight path on a level
road with no pressure on the steering wheel.
Lead is usually caused by:
1) Incorrect alignment.
2) Uneven brake adjustment.
3) Tire construction.
The way in which a tire is built can produce lead in a vehicle. An ex-
ample of this is placement of the belt. Off center belts on radial tires
can cause the tire to develop a side force while rolling straight down
the road. If one side of the tire is a little larger diameter than the oth-
er, the tire will tend to roll to one side. This will develop a side force
which can produce vehicle lead.
The procedure on previous page should be used to make sure that
front alignment is not mistaken for tire lead.
1) Part of the lead diagnosis procedure is different from the tire
rotation pattern currently in the owner's and service manuals. If
a medium to high mileage tire is moved to the other side of the
vehicle, be sure to check that ride roughness has not developed.
2) Rear tires will not cause lead.
VIBRATION DIAGNOSIS
Wheel unbalance causes most of the highway speed vibration
problems. If a vibration remains after dynamic balancing, it can be
caused by three things.
1) Tire runout.
2) Wheel runout.
3) Tire stiffness variation.
Measuring tire and / or wheel free runout will uncover only part of the
problem. All three causes, known as loaded radial runout, must be
checked by using a Tire Problem Detector (TPD). If a TPD is not
available, the more time consuming method of substituting known
good tire and wheel assemblies on the problem vehicle can be
used.

YH4
GRAND
VITARA
STEERING, SUSPENSION, WHEELS AND TIRES 3-9
Caused bySMOOTH ROADSUSPENSION MOVEMENT
(Loaded Runout)
TIRE OUT
OF
ROUNDTIRE
STIFFNESS
VARIATIONRIM BENT
OR
OUT OF ROUND

YH4
GRAND
VITARA
3A
Alignment service data (without load)
Toe-in (Toe-in gauge measurement)
ªBº ± ªAº: 0
2 mm (0
0.08 in.)
Camber angle ªCº: 0'
1

Caster: 2
40'
1

*1. Forward
*2. Body center[A] : Top view
[B] : Front view
1. Center line of wheel
FRONT END ALIGNMENT 3A-1
SECTION 3A
FRONT END ALIGNMENT
CONTENTS
DIAGNOSIS3-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL INFORMATION3A-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Toe-Setting3A-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Camber3A-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preliminary Checks Prior to Adjusting Front Alignment 3A-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Toe Adjustment3A-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Camber and Caster Adjustment 3A-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering Angle3A-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL INFORMATION
Front alignment refers to the angular relationship between the front wheels, the front suspension attaching parts
and the ground. Generally, the only adjustment required for front alignment is toe setting.
Camber and caster can't be adjusted. Therefore, should camber or caster be out of specification due to the damage
caused by hazardous road conditions or collision, whether the damage is in body or in suspension should be deter-
mined. If the body is damaged, it should be repaired and if suspension is damaged, it should replaced.
TOE SETTING
Toe is the turning in or out of the front wheels. The purpose of a toe specification is to ensure parallel rolling of the
front wheels (Excessive toe-in or toe-out may increase tire wear).
Amount of toe can be obtained by subtracting ªAº front ªBº as shown in above figure and therefore is given in mm
(in.).

YH4
GRAND
VITARA
3A-2 FRONT END ALIGNMENT
CAMBER
Camber is the tilting of the front wheels from the vertical, as viewed from the front of the vehicle. When the wheels
tilt outward at the top, the camber is positive. When the wheels tilt inward at the top, the camber is negative. The
amount of tilt is measured in degrees.
PRELIMINARY CHECKS PRIOR TO ADJUSTING FRONT ALIGNMENT
Steering and vibration complaints are not always the result of improper alignment. An additional item to be checked
is the possibility of tire lead due to worn or improperly manufactured tires. ªLeadº is the deviation of the vehicle from
a straight path on a level road without hand pressure on the steering wheel.
Section 3 of this manual contains a procedure for determining the presence of a tire lead problem.
Before making any adjustment affecting toe setting, the following checks and inspections should be made to en-
sure correctness of alignment readings and alignment adjustments:
1) Check all tires for proper inflation pressures and approximately the same tread wear.
2) Check for loose ball joints. Check tie rod ends; if excessive looseness is noted, it must be corrected before ad-
justing.
3) Check for run-out of wheels and tires.
4) Check vehicle trim heights; if out of limits and a correction is to be made, it must be made before adjusting toe.
5) Check for loose control arms.
6) Check for loose or missing stabilizer bar attachments.
7) Consideration must be given to excess loads, such as tool boxes. If this excess load is normally carried in ve-
hicle, it should remain in vehicle during alignment checks.
8) Consider condition of equipment being used to check alignment and follow manufacturer's instructions.
9) Regardless of equipment used to check alignment, vehicle must be on a level surface both fore and aft and
transversely.
TOE ADJUSTMENT
Toe is adjusted by changing tie rod length. Loosen right and left tie
rod end lock nuts first and then rotate right and left tie rods by the
same amount to align toe-in to specification.
In this adjustment, right and left tie rods should become equal in
length.
After adjustment, tighten lock nuts to specified torque.
Tightening Torque
(a): 65 N
.m (6.5 kg-m, 47.0 lb-ft)
CAMBER AND CASTER ADJUSTMENT
Should camber or caster be found out of specifications upon in-
spection, locate its cause first. If it is in damaged, loose, bent,
dented or worn suspension parts, they should be replaced. If it is
in body, repair it so as to attain specifications.
To prevent possible incorrect reading of camber or caster, vehicle
front end must be moved up and down a few times before inspec-
tion.

YH4
GRAND
VITARA
3D-22 FRONT SUSPENSION
1. Hydraulic press
2. Front bushing
A: Bushing flange
contacts housing edge
1. Hydraulic press
2. Rear bushing
A: Bushing flange
contacts housing edge
INSTALLATION
1) Front bushing
Press-fit front bushing until its flange contacts housing edge of
control arm, use special tools as shown.
Special Tool
(C): 09951-16060
(F): 09913-85210
NOTE:
When press-fitting bushing, compounding oil or soap water
applied to inside of control arm housing will facilitate work.
2) Rear bushing
Press-fit rear bushing until its flange contacts housing edge of
control arm, use special tools as shown.
Special Tool
(E): 09925-58210
(F): 09913-85210
NOTE:
When press-fitting bushing, compounding oil or soap water
applied to inside of control arm housing will facilitate work.
3) Install control arm to chassis.
Tighten suspension arm nut to specified torque after lowering
hoist and vehicle in non-loaded condition.
Tightening Torque
(a): 85 N
.m (8.5 kg-m, 61.5 lb-ft)
(b): 127 N.m (12.7 kg-m, 92.0 lb-ft)
4) As installation procedure hereafter is the same as that for coil
spring. Refer to ªCOIL SPRINGº in this section.
NOTE:
For any tightening torque other than those specified in text,
refer to ªTORQUE SPECIFICATION TABLEº at the end of
this section.

YH4
GRAND
VITARA
1. Rear axle housing
2. Floor jack
1. Lock nut (if equipped)
2. Absorber nut
3. Upper support
4. Rubber bush
5. Lower support
6. Shock absorber
7. Bolt
Upper side
Lower side
1. Lock nut (if equipped)
2. Absorber nut
3. Body outside
REAR SUSPENSION 3E-5
ON-VEHICLE SERVICE
SHOCK ABSORBER
The shock absorber is non-adjustable, non-refillable, and cannot
be disassembled. The only service the shock absorber requires is
replacement when it has lost its resistance, is damaged, or leaking
fluid.
REMOVAL
1) Hoist vehicle and remove rear wheel.
2) Support rear axle housing by using floor jack to prevent it from
lowering.
3) Remove lock nut (if equipped) and absorber nut.
4) Remove lower mounting bolt.
5) Remove shock absorber.
INSTALLATION
1) Install shock absorber. Refer to figure for proper installing direc-
tion of lower mounting bolt.
2) Remove floor jack.
3) Lower hoist.
4) Tighten nuts to specified torque.
NOTE:

Tighten lower nut with vehicle off hoist and in non-loaded
condition.
Tightening Torque
(a): 29 N
.m (2.9 kg-m, 21.0 lb-ft)
(b): 85 N
.m (8.5 kg-m. 61.5 lb-ft)