Switch SUZUKI GRAND VITARA 2003 2.G Service Repair Manual

YH4
GRAND
VITARA
1. Steering column
2. Mounting bolt
3. Steering column lower seal
4. Dash panel
1. Steering column lower seal
In engine room
In cabin
1. Shift (key) interlock cable
2. Screw
3C1-12 AIR BAG STEERING WHEEL AND COLUMN
4) Check steering column lower seal for breakage or deformation.
If found defective, replace.
5) Check steering shaft joints and shaft for any damages such as
crack, breakage, malfunction or excessive play.
If anything is found faulty, replace as steering lower shaft assem-
bly or steering column assembly.
6) Check steering shaft for smooth rotation.
If found defective, replace as column assembly.
7) Check steering shaft and column for bend, cracks or deforma-
tion.
If found defective, replace as column assembly.
INSTALLATION
CAUTION:
After tightening steering column mounting bolts, steering
shaft joint bolts should be tightened.
1) Be sure that front wheels and steering wheel are in straight-
ahead position.
2) If equipped with shift (key) interlock cable, install shift (key) inter-
lock cable to ignition switch.
Tightening Torque
(a): 2.2 N
.m (0.22 kg-m, 1.6 lb-ft)
3) Install steering column assembly to dash panel and upper
bracket so that boss of steering column lower seal and all around
it project out of hole in dash panel into engine room. Tighten
steering column lower bolts (4 pieces) first and then upper bolts
(2 pieces) to specified torque.
Tightening Torque
(b): 23 N
.m (2.3 kg-m, 17.0 lb-ft)

YH4
GRAND
VITARA
1. Steering shaft joint
2. Steering shaft (column side)
3. Marks
1. Steering shaft joint
2. Bolt (column side)
3. Bolt (lower shaft assembly side)
1. Steering column hole cover
1
AIR BAG STEERING WHEEL AND COLUMN 3C1-13
4) Install steering shaft joint to steering shaft by matching it to
marks made before removal.
5) Install shaft joint bolt (column side) to steering shaft joint. Tighten
shaft joint bolt (column side) to specified torque first and then
shaft joint bolt (lower shaft assembly side) to specified torque.
Tightening Torque
(c): 25 N
.m (2.5 kg-m, 18.0 lb-ft)
6) If contact coil and combination switch assembly is removed,
install it, referring to ªCONTACT COIL AND COMBINATION
SWITCH ASSEMBLYº in this section.
7) Connect all connectors that have been removed in removal.
8) Install steering column hole cover.
9) If steering wheel is removed, install it by referring to ªSTEER-
ING WHEELº in this section.
10) Connect negative battery cable.
11) After installing steering column assembly, be sure to enable air
bag system by referring to ªENABLING AIR BAG SYSTEMº un-
der ªSERVICE PRECAUTIONSº in Section 10B.

YH4
GRAND
VITARA
3C1-14 AIR BAG STEERING WHEEL AND COLUMN
1. Steering column
2. Steering lock 1
2
1. Center punch (with sharp point)
2. Steering lock mounting bolt
1. Steering column
2. Steering shaft
STEERING LOCK ASSEMBLY (IGNITION
SWITCH)
REMOVAL
1) Remove steering column. Refer to ªSTEERING COLUMNº in
this section.
2) Using center punch as shown, loosen and remove steering lock
mounting bolts.
NOTE:
Use care not to damage aluminum part of steering lock
body with center punch.
3) Turn ignition key to ªACCº or ªONº position and remove steering
lock assembly from steering column.
INSTALLATION
1) Position oblong hole of steering shaft in the center of hole in col-
umn.
2) Turn ignition key to ªACCº or ªONº position and install steering
lock assembly onto column.
3) Now turn ignition key to ªLOCKº position and pull it out.
4) Align hub on lock with oblong hole of steering shaft and rotate
shaft to assure that steering shaft is locked.
5) Tighten new bolts until head of each bolt is broken off.
6) Turn ignition key to ªACCº or ªONº position and check to be sure
that steering shaft rotates smoothly. Also check for lock opera-
tion.
7) Install steering column. Refer to ªSTEERING COLUMNº in this
section.

YH4
GRAND
VITARA
AIR BAG STEERING WHEEL AND COLUMN 3C1-15
1. Steering column assembly
2. Steering shaft joint
1. Steering column assembly
2. Steering shaft joint
3. Steering lower shaft assembly
4. Bolt (column side)
5. Bolt (lower shaft assembly side)
1. Steering lower shaft assembly
2. Steering lower shaft assembly
lower joint bolt
3. Steering shaft joint
STEERING LOWER SHAFT ASSEMBLY
CAUTION:
Never turn steering wheel while steering lower shaft assem-
bly is removed.
Should it have been turned and contact coil (on combina-
tion switch) have got out of its centered position, it needs
to be centered again. Also, turning steering wheel more
than about two and a half turns will break contact coil.
REMOVAL
1) Turn steering wheel so that vehicle's front tires are at straight-
ahead position.
2) Turn ignition switch to ªLOCKº position and remove key.
3) After removing bolt on column side of shaft joint and loosening
bolt on its lower shaft assembly side, move shaft joint to lower
shaft assembly side (in arrow direction in figure).
4) Remove lower shaft assembly lower joint bolt and then remove
lower shaft assembly.
5) Remove shaft joint bolt (lower shaft assembly side) from shaft
joint and then remove shaft joint from lower shaft assembly.

YH4
GRAND
VITARA
5
BRAKES 5-1
GENERAL DESCRIPTION5- 2 . . . . . . . . . . . . . .
DIAGNOSIS5- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Road Testing Brakes 5- 3. . . . . . . . . . . . . . . . . .
Brake Fluid Leaks 5- 3. . . . . . . . . . . . . . . . . . . .
Substandard or Contaminated
Brake Fluid 5- 3. . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table 5- 4. . . . . . . . . . . . . . . . . . . . . .
CHECK AND ADJUSTMENT5- 7 . . . . . . . . . . . .
Bleeding Brakes 5- 7. . . . . . . . . . . . . . . . . . . . . .
Brake Pedal Free Height Check 5- 9. . . . . . . .
Brake Light Switch Adjustment 5- 9. . . . . . . . .
Excessive Pedal Travel Check 5- 9. . . . . . . . .
Brake Pedal Play Check 5-10. . . . . . . . . . . . . . .
Brake Fluid Level Check 5-10. . . . . . . . . . . . . . . Brake Hose and Pipe Check 5-10. . . . . . . . . . .
Master Cylinder Check 5-10. . . . . . . . . . . . . . . .
Brake Disc Check 5-11. . . . . . . . . . . . . . . . . . . .
Brake Pad Check 5-11. . . . . . . . . . . . . . . . . . . . .
Brake Shoe Check 5-11. . . . . . . . . . . . . . . . . . . .
Parking Brake Check and
Adjustment 5-12. . . . . . . . . . . . . . . . . . . . . . . . .
Flushing Brake Hydraulic System 5-13. . . . . . .
Fluid Pressure Test 5-13. . . . . . . . . . . . . . . . . . .
Booster Operation Check 5-15. . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS5-17 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIAL5-17 . . . . . . . .
SPECIAL TOOLS5-18 . . . . . . . . . . . . . . . . . . . . . .
SECTION 5
BRAKES
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
NOTE:

When inspecting and servicing vehicle equipped with ABS, be sure to refer to section 5E or 5E1 first.

All brake fasteners are important attaching parts in that they could affect the performance of vital parts
and systems, and / or could result in major repair expense. They must be replaced with one of same part
number or with an equivalent part if replacement becomes necessary. Do not use a replacement part of
lesser quality or substitute design. Torque values must be used as specified during reassembly to as-
sure proper retention of all parts. There is to be no welding as it may result in extensive damage and
weakening of the metal.
DIAGNOSIS5-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BRAKE PIPE / HOSE / MASTER CYLINDER5A-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRONT BRAKE5B-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PARKING AND REAR BRAKE5C-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTENTS

YH4
GRAND
VITARA
5-6 BRAKES
ConditionPossible CauseCorrection
Brake warning light
turns on after
engine start
Parking brake applied.

Insufficient amount of brake fluid.

Brake fluid leaking from brake line.

Brake warning light circuit faulty.

Malfunctioning EBD system, if equipped
with ABS.Release parking brake and check
that brake warning light turns off.
Add brake fluid.
Investigate leaky point, correct it and
add brake fluid.
Repair circuit.
Check system referring to
ªDIAGNOSISº of ABS section.
Brake warning light
turns on when
brake is applied
Brake fluid leaking from brake line.

Insufficient amount of brake fluid.Investigate leaky point, correct it and
add brake fluid.
Add brake fluid.
Brake warning light
fails to turn on
even when parking
brake is applied
Bulb burnt out.

Brake warning light circuit open.Replace bulb.
Repair circuit.
ABS warning light
does not turn on
for 2 sec. after
ignition switch has
turned ON
Bulb burnt out.

ABS warning light circuit open, if equipped
with ABS. (including check relay)Replace bulb.
Check system referring to
ªDIAGNOSISº of ABS section.
ABS warning light
remains on after
ignition switch has
turned on for 2 sec.
Malfunctioning ABS, if equipped with ABS.Check system referring to
ªDIAGNOSISº of ABS section.

YH4
GRAND
VITARA
1. 4-way joint / 2-way joint
2. Master cylinder
3. LSPV
4. Right brake caliper
5. Left brake caliper
6. Right wheel cylinder
7. Left wheel cylinder
8. ABS actuator

: Air bleeding point [A]: Without ABS
[B]: With ABS
1. Plug cap2. Vinyl tube (See-through tube)
3. Container
[A]
[B]
BRAKES 5-7
CHECK AND ADJUSTMENT
BLEEDING BRAKES
CAUTION:
Brake fluid is extremely damaging to paint. If fluid should
accidentally touch painted surface, immediately wipe
fluid from paint and clean painted surface.
NOTE:
For vehicle equipped with ABS, make sure that ignition switch
turns off.
Be sure to bleed air of brake system according to following proce-
dure when its oil hydraulic circuit has been disconnected.
Hydraulic lines of brake system consists of two separate lines, one
for front wheel brakes and the other for rear wheel brakes.
Air bleeding is necessary at right and left front wheel brakes, left
rear wheel brake and LSPV (if equipped without ABS), i.e. 4 places
(3 places for vehicle with ABS) in all.
1) Fill master cylinder reservoir with brake fluid and keep at least
one-half full of fluid during bleeding operation.
2) Remove bleeder plug cap.
Attach a vinyl tube to bleeder plug of wheel cylinder, and insert
the other end into container.
3) Depress brake pedal several times, and then while holding it de-
pressed, loosen bleeder plug about one-third to one half turn.

YH4
GRAND
VITARA
1. Stop light switch
BRAKES 5-9
BRAKE PEDAL FREE HEIGHT CHECK
Remove foot rest and displace carpet and dash silencer(s) so as to
measure brake pedal free height between pedal face and asphalt
sheet installed on dash panel.
Brake pedal free height ªaº from asphalt sheet:
208 ± 218 mm (8.19 ± 8.58 in.)
If the measurement is not within the specification, check the posi-
tion of booster push rod clevis and / or stop light switch according
to the instruction shown in this section.
The free height varies depending on installation position of booster
push rod clevis and stop light switch.
BRAKE LIGHT SWITCH ADJUSTMENT
Adjustment should be made as follows when installing switch. Pull
up brake pedal toward you and while holding it there, adjust switch
position so that clearance between end of thread and brake pedal
return cushion (shown as ªbº in figure).
Then tighten lock nut to specified torque.
Clearance ªbº: 1.5 ± 2.0 mm (0.06 ± 0.08 in.)
Tightening Torque
(b): 7.5 N
.m (0.75 kg-m, 5.5 lb-ft)
EXCESSIVE PEDAL TRAVEL CHECK
1) Remove foot rest and displace carpet and dash silencer(s).
2) Start engine.
3) Depress brake pedal a few times.
4) With brake pedal depressed with approximately 30 kg (66 lbs)
load, measure pedal to asphalt sheet clearance ªcº.
Clearance ªcº: over 115 mm (4.53 in.)
5) If clearance ªcº is less than specification, the most possible
cause is either rear brake shoes are worn out beyond limit or air
is in lines.
Should clearance ªcº remain less than specification even after
replacement of brake shoes and bleeding of system, other pos-
sible but infrequent cause is malfunction of rear brake shoe ad-
justers or booster push rod length out of adjustment.

YH4
GRAND
VITARA
5-10 BRAKES
BRAKE PEDAL PLAY CHECK
Pedal play should be within specification. If out of specification,
check brake light switch for proper installation position and adjust
if necessary.
Also check pedal shaft bolt and master cylinder pin installation for
looseness and replace if defective.
Pedal play ªdº: 1 ± 8 mm (0.04 ± 0.32 in.)
BRAKE FLUID LEVEL CHECK
Be sure to use particular brake fluid either as indicated on reservoir
cap of that vehicle or recommended in owner's manual which
comes along with that vehicle.
Use of any other fluid is strictly prohibited.
Fluid level should be between MIN and MAX lines marked on reser-
voir.
When warning light lights sometimes during driving, replenish fluid
to MAX line.
When fluid decreases quickly, inspect brake system for leakage.
Correct leaky points and then refill to specified level.
CAUTION:
Do not use shock absorber fluid or any other fluid which
contains mineral oil. Do not use a container which has been
used for mineral oil or a container which is wet from water.
Mineral oil will cause swelling and distortion of rubber parts
in hydraulic brake system and water mixed into brake fluid
will lower fluid boiling point. Keep all fluid containers
capped to prevent contamination.
BRAKE HOSE AND PIPE CHECK
The brake hose assembly should be checked for road hazard dam-
age, for cracks and chafing of the outer cover, for leaks and blisters.
A light and mirror may be needed for an adequate inspection. If any
of the above conditions are observed on the brake hose, it is neces-
sary to replace it.
Inspect the pipe for damage, cracks, dents and corrosion. If any de-
fect is found, replace it.
MASTER CYLINDER CHECK
Check for a cracked master cylinder casting or brake fluid around
the master cylinder. Leaks are indicated only if there is at least a
drop of fluid. A damp condition is not abnormal.

YH4
GRAND
VITARA
BRAKES 5-17
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Brake pipe 2-way (or 4-way) joint bolt232.317.0
Brake pipe flare nut161.611.5
Front caliperM88.00.86.0
Brake bleederplug
Front cali erM108.50.856.5Brake bleeder lugWheel cylinder7.50.755.5
LSPV7.50.755.5
LSPV mounting bolt
LSPV stay bolt232.317.0
LSPV spring nut
Wheel nut10010.072.5
Stop light switch lock nut7.50.755.5
REQUIRED SERVICE MATERIAL
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
Brake fluid
Indicated on reservoir
cap or described in owner's
manual of vehicle
To fill master cylinder reservoir.

To clean and apply to inner parts of master
cylinder caliper and wheel cylinder when
they are disassembled.