lamp SUZUKI GRAND VITARA 2004 2.G Service Workshop Manual

YH4
GRAND
VITARA
1. Yellow connector of passenger air bag (inflator) module
2. Steering support member
3. Air bag harness
AIR BAG SYSTEM 10B-57
3) Connect Yellow connector of passenger air bag (inflator) mod-
ule, and be sure to lock connector with lock lever.
ii) Connect connector.
ii) Lock connector with lock lever.
4) Install glove box.
5) Install ªAIR BAGº fuse to ªAIR BAGº fuse box.
6) Turn ignition switch to ON and verify that ªAIR BAGº warning
lamp flashes 6 times and then turns off.
If it does not operate as described, perform ªAir Bag Diagnostic
System Checkº in this section.
HANDLING AND STORAGE
SDM
WARNING:
Never power up air bag system when SDM is not rigidly at-
tached to the vehicle. Otherwise, personal injury may result.
CAUTION:
After detecting one time of such collision as to meet deploy-
ment conditions, the SDM must not be used.
Refer to ªDiagnosisº when checking the SDM.

Never attempt disassembly of SDM.

When storing SDM, select a place where neither high tempera-
ture nor high humidity is anticipated and oil, water and dust are
kept off.

If SDM was dropped from a height of 90 cm (3 ft) or more or if it
is found to be damaged or deformed, replace it with a new one.

If installation part of SDM was damaged, repair that part com-
pletely before reinstallation.

All SDM and mounting bracket fasteners must be carefully
torqued and the arrow must be pointed toward the front of the ve-
hicle to ensure proper operation of the air bag system.

YH4
GRAND
VITARA
1. SDM
2. SDM connector
3. SDM plate
4. SDM cover
1. Air bag wire harness
2. Ground
3. SDM case ground
AIR BAG SYSTEM 10B-65

Passenger air bag (inflator) module
± Check for dents, cracks, damage or fitness.
± Check trim cover for cracks or deformities.
± Check harness and connector for damage or tightness.
If any faulty condition is found in above checks, replace.

SDM and SDM plate
± Check for external damage such as deformation, scratch,
crack, peeled paint, etc.
± Check whether SDM can installed properly due to a cause in it-
self. (There is a gap between SDM and SDM plate, or it cannot
be fixed securely.)
± Check whether connector or lead wire of SDM has a scorching,
melting or damage.
± Check whether connector can be connected securely or locked.
± Check SDM connector and terminals for tightness.
± Check SDM sets a diagnostic trouble code and the diagnostic
table leads to a malfunctioning SDM.
If any faulty condition is found in above checks, replace.

Air bag wire harness and connections
± Check for damages, deformities or poor connections.
(Refer to ªIntermittent And Poor Connectionsº in this section.)
± Check wire harness clamps for tightness.
If any faulty condition is found, correct or replace.

YH4
GRAND
VITARA
2-2
2-1. Webbing
2-2. Retractor assembly
2-1. Seat belt pretensioner
2-2. Seat belt pretensioner harness
10B-66 AIR BAG SYSTEM

Seat belt pretensioner
± Check for dents, cracks, damage or fitness.
± Check harness and connector for damage or tightness.
If any faulty condition is found in above checks, replace.

Seat belts and mounting points
± Refer to SECTION 10A.

ªAIR BAGº warning lamp (air bag system)
± After vehicle is completely repaired, perform ªAir Bag Diagnos-
tic System Checkº under ªDiagnosisº in this section.
DRIVER AIR BAG (INFLATOR) MODULE
Refer to SECTION 3C1 for removal, inspection and installation.
CONTACT COIL AND COMBINATION SWITCH
ASSEMBLY
Refer to SECTION 3C1 for removal, inspection and installation.
SEAT BELT PRETENSIONER
Refer to SECTION 10A for removal, inspection and installation.
ªAIR BAGº WARNING LAMP
Refer to SECTION 8C for removal and installation of combination
meter.