remote control SUZUKI NEXA 2015 1.G User Guide

Downloaded from www.Manualslib.com manuals search engine %()25('5,9,1*
06(
6HFXULW\6\VWHPLIHTXLSSHGThe security system is armed in about 5
seconds after you lock all doors (including
the tailgate) by using the keyless entry sys-
tem transmitter, keyless push start system
remote controller or request switch.
Once the system is armed, any attempt to
open a door by using any other means (*)
than the keyless entry system transmitter,
keyless push start system remote control-
ler or request switch, or open the engine
hood, will cause the alarm to be triggered.
* These means include the following:
– The key
– The lock knob on a door
– The central door locking switchAlso, in case that you have set the shock
sensor to enabled state and set sensitivity
of the pre-warning function and full blast
warning function to a level other than 0, the
alarm will be triggered if any attempt is
made to tamper with the vehicle. The shock
sensor can be selected to enabled or dis-
abled state, and sensitivity of each warning
can be adjusted as desired. To set the
shock sensor, ask your DXWKRULVHG 0DUXWL
6X]XNLZRUNVKRSor use the setting mode of
theinformation display.NOTE:
• The default setting of the shock sensor
is in the disabled state. Set to the
enabled state and adjust sensitivity of
each warning according to your prefer-
ence. For details on how to use the infor-mation display, refer to “Information
Display” in this section.
• Your dealer may have already set the
shock sensor of the vehicle to the
enabled state before you purchase it.
Consult your dealer for further informa-
tion.
NOTE:
• The security system generates alarms
when any of the predetermined condi-
tions is met. However, the system does
not have any function of blocking unau-
thorized entry into the vehicle.
• Always use the keyless entry system
transmitter, keyless push start system
remote controller or request switch to
unlock the doors when the security sys-
tem has been armed. Using a key
instead will trigger the alarm.
• If a person who does not know the secu-
rity system is going to drive the vehicle,
we recommend you explain the system
and its operation to the person, or dis-
able the system beforehand. Mistakenly
triggering the alarm may cause a nui-
sance to others.
• Even if the security system is armed,
you should still be careful to guard
against theft. Do not leave money or
things of value in the vehicle.+RZWRDUPWKHVHFXULW\V\VWHP
ZKHQHQDEOHG
Lock all doors (including the tailgate) using
the keyless entry system transmitter, key-
less push start system remote controller or
request switch. The security system indica-
tor (1) will start blinking rapidly, and the
security system will be armed in about 5
seconds.
While the system is being armed, the indi-
cator continues to blink at intervals of
approximately 2 seconds
61MM0A134
NOTE:
• To prevent the alarm from being acci-
dentally triggered, avoid arming it while
anyone remains inside the vehicle. The
alarm will be triggered if any person
inside opens the door or engine hood, or
swings the vehicle (if the shock sensor is
in the enabled state).
• The security system is not armed when
all doors are locked using the key from
(1)

Downloaded from www.Manualslib.com manuals search engine 
%()25('5,9,1*
06(
outside, or using the door lock knobs or
the central door locking switch from
inside.
• If any door is not operated within approx-
imately 30 seconds after the doors have
been unlocked using the keyless entry
system transmitter, keyless push start
system remote controller or request
switch, the doors are automatically
locked again. When the doors are
locked, the security system will be
armed in about 5 seconds if the system
is in the enabled state.
• If the security system indicator (1) blinks
when the ignition switch is in the “ON”
position or the ignition mode is “ON”,
there may be something wrong with the
security system. Ask your
DXWKRULVHG 0DUXWL 6X]XNL ZRUNVKRS to
inspect the system.
+RZWRGLVDUPWKHVHFXULW\V\VWHP
Simply unlock the doors using the keyless
entry system transmitter, keyless push
start system remote controller or request
switch. The security system indicator will
go out, indicating that the security system
is disarmed.
+RZWRVWRSWKHDODUP
Should the alarm be triggered accidentally,
unlock the doors using the keyless entry
system transmitter, keyless push start sys-
tem remote controller or request switch, or
insert the key in the ignition switch and turn
it to “ON” position, or press the engineswitch to change the ignition mode to
“ON”. The alarm will then stop.
NOTE:
• Even after the alarm has stopped, if you
lock the doors using the keyless entry
system transmitter, keyless push start
system remote controller or request
switch, the security system will be
rearmed with a delay of about 5 sec-
onds.
• If you disconnect the battery while the
security system is in the armed condition
or the alarm is actually in operation, the
alarm will be re-triggered when the bat-
tery is then reconnected.
• Even after the alarm has stopped at the
end of the predetermined operation time,
it will be triggered again if any of the
doors or engine hood is opened, or the
vehicle feels a shock (if the shock sen-
sor is in the enabled state), without dis-
arming the security system.
&KHFNLQJZKHWKHUWKHDODUPKDVEHHQ
WULJJHUHGGXULQJSDUNLQJ
If the alarm was triggered and you then
turn the ignition switch to “ON” position, or
press the engine switch to change the igni-
tion mode to “ON”, the security system
indicator will blink rapidly for about 8 sec-
onds and a buzzer will beep 4 times during
this period. If this happens, check whether
the vehicle has been broken into while you
were away from it.(QDEOLQJDQGGLVDEOLQJWKHVHFXULW\
V\VWHP
The security system can be either enabled
or disabled.
:KHQHQDEOHG
• If any of the doors are opened without
unlocking by the keyless entry system
transmitter, keyless push start system
remote controller or request switch, all
turn signal lights start to blink and the
interior buzzer beeps intermittently. After
5 seconds, the siren will sound for about
27.5 seconds. The security system indi-
cator continues to blink during this time.
• If the engine hood is opened, all turn sig-
nal lights blink, and the siren sounds for
about 27.5 seconds. The security sys-
tem indicator continues to blink during
this time.
(,IWKHVKRFNVHQVRULVLQWKHHQDEOHG
VWDWH
• If the vehicle feels a shock, the siren
sounds for about 2 seconds (pre-warn-
ing). If the vehicle continues to feel a
shock, all turn signal lights start to blink
and the interior buzzer beeps intermit-
tently. After 5 seconds, the siren will
sound for about 27.5 seconds (full blast
warning). The security system indicator
continues to blink during this time.
NOTE:
If you set the full blast warning sensitivity
higher than the pre-warning sensitivity in
the setting mode of the information display,
or the vehicle feels such shock as to be

Downloaded from www.Manualslib.com manuals search engine %()25('5,9,1*
06(
:DUQLQJDQG,QGLFDWRU
0HVVDJH0DVWHU:DUQLQJ
,QGLFDWRU/LJKW6RXQG &DXVHDQG5HPHG\
Keyless Push Start System
61MM0A170
Blinks Series of beeps under cer-
tain conditions (for about 2
seconds from exterior and/or
interior buzzers)The remote controller may be outside the
vehicle or its battery may have become dis-
charged. Locate the remote controller or
touch the engine switch with the remote
controller.
If the message still appears, replace the
remote controller battery.
61MM0A171

Downloaded from www.Manualslib.com manuals search engine %()25('5,9,1*
06(
(#1) This message will disappear for a while even if the problem that caused the message to appear is not corrected.:DUQLQJDQG,QGLFDWRU
0HVVDJH0DVWHU:DUQLQJ
,QGLFDWRU/LJKW6RXQG &DXVHDQG5HPHG\
61MM0A176
Off Off The road may be icy. Drive very carefully.
(#1)
Keyless Push Start System
61MM0A177
Off Off The remote controller battery is about to
become flat. Replace the battery. (#1)
61MM0A225
Blinks Beep (one time from interior
buzzer) There may be a problem with the fuel filter.
Have your vehicle inspected by an autho-
rized MDUXWL6X]XNLZRUNVKRS.

Downloaded from www.Manualslib.com manuals search engine 
23(5$7,1*<2859(+,&/(
06(
NOTE:
In the presence of strong radio signals or
noise, you may not be able to change the
ignition mode to ACC or ON or to start the
engine using the engine switch. In this
case, the information display on the instru-
ment cluster will show the following mes-
sage: KEY FOB NOT DETECTED.8QUHOHDVHG6WHHULQJ/RFN:DUQLQJIf the steering lock remains engaged when
you press the engine switch to change the
ignition mode to “ON”, the information dis-
play in the instrument cluster shows the
message: “TRN. STEERING WHEEL TO
RELEASE LOCK”. Refer to “Information
Display” in the ³%()25( '5,9,1*´ sec-
tion for details.
NOTE:
The steering lock may not be released if
some load is acting on the steering wheel.
If this happens, turn the steering wheel to
the right or left to relieve it from the load
before you press the engine switch again
to change to the desired ignition mode.
.H\OHVV3XVK6WDUW6\VWHP
LIHTXLSSHGProvided the keyless push start system
remote controller is within the “interior
workable area” (refer to the related expla-
nation in this section), you can use the
engine switch for starting the engine and
selecting an ignition mode (ACC or ON). In
addition, the following functions can be
used:
• Keyless entry function. Refer to “Keyless
Push Start System Remote Controller” in
the “BEFORE DRIVING” section for
details.
• Locking and unlocking doors (including
the tailgate) using a request switch.
Refer to “Keyless Push Start System
Remote Controller” in the “BEFORE
DRIVING” section for details.
• Immobilizer (anti-theft) function. Refer to
“Immobilizer System” in the “BEFORE
DRIVING” section for details.(QJLQH6ZLWFK,OOXPLQDWLRQThe engine switch is illuminated (lit) in the
following situations:
• When the engine is off and the driver’s
door is open or for 15 seconds after the
drivers door is closed.
• When the engine is off and the position
lights are on. The illumination will go out
when the position lights are turned off.
• When the engine is on and the position
lights and/or the headlights are on. Theillumination will go out when the head-
lights are turned off.
82K253
NOTE:
To save the battery, the illumination will be
automatically turned off when both of the
following conditions are simultaneously
met:
• The headlights and position lights are
turned off.
• A period of 15 minutes has elapsed after
opening the driver’s door.6HOHFWLRQRI,JQLWLRQ0RGHVPress the engine switch to select the
“ACC” or “ON” mode as follows when you
use an electric accessory or check the
operation of instruments without running
the engine.
1) Bring the keyless push start system
remote controller with you and sit in the
driver’s seat.

Downloaded from www.Manualslib.com manuals search engine (1)
(2)
23(5$7,1*<2859(+,&/(
06(
2) Without depressing the clutch pedal,
press the engine switch (1).
82K254
Every time you press the engine switch,
the ignition mode changes as follows.
57L31033
NOTE:
When selecting the ignition modes, the
information display in the instrument clus-
ter shows certain messages. Refer to
“Information Display” in the “BEFORE
DRIVING” section for details.,IWKH0$67(5:$51,1*LQGLFDWRUOLJKW
EOLQNV DQG WKH LJQLWLRQ PRGHV FDQQRW
EHVHOHFWHG
Your keyless push start system remote con-
troller may not be sensed as being within the
“interior workable area” (refer to the related
explanation in this section). Try again after
making sure you have the remote controller
with you. If the ignition modes still cannot be
selected, the battery of the remote controller
may be discharged. To be able to select an
ignition mode, you must then use the follow-
ing method:
58MST0302
1) Without depressing the brake pedal
and the clutch pedal, push the engine
switch (1).
2) Within about 10 seconds during which
the master warning indicator light in the
instrument cluster is blinking and the
“PLACE KEY FOB ON START
SWITCH” message appears on the
information display, touch the engineswitch with the lock button end of the
remote controller (2) for about 2 sec-
onds.
NOTE:
•
If you still cannot select the ignition
modes, there may be some problem with
the keyless push start system. Contact
an DXWKRULVHG 0DUXWL 6X]XNL ZRUNVKRS
for an inspection of the system.
• The immobilizer/keyless push start sys-
tem warning light will come on for about
5 seconds while the master warning indi-
cator light is blinking. In addition, the
information display in the instrument
cluster will show a message during this
time. Refer to “Information Display” in
the “BEFORE DRIVING” section for
details.
•
You may customize the system to cause
the interior buzzer to sound once for the
remote controller out of sensing range
warning. To incorporate this customiza-
tion, please contact an DXWKRULVHG0DUXWL
6X]XNLZRUNVKRS
• If the battery of the remote controller is
about to become completely discharged,
the corresponding message will appear
on the information display when you
press the engine switch to change the
ignition mode to ON. Refer to “Informa-
tion Display” in the “BEFORE DRIVING”
section for details. For details on replac-
ing the battery, refer to the “Keyless
Push Start System Remote Controller” in
the “BEFORE DRIVING” section.
(OFF)
ON ACC LOCK
(Audio equipment)
(;$03/(
(1)

Downloaded from www.Manualslib.com manuals search engine 
23(5$7,1*<2859(+,&/(
06(
5HPRWH&RQWUROOHU2XWVLGH:DUQLQJWhen either of the conditions described
below is met, the system issues the remote
controller outside warning by sounding the
interior and exterior buzzers. At the same
time, the immobilizer/keyless push start
system warning light comes on and the
master warning indicator light blinks.
• Any door is opened and then closed
while the remote controller is not inside
the vehicle and the engine is running or
the ignition mode has been changed to
“ACC” or “ON” by pressing the engine
switch.
• The remote controller is not inside the
vehicle when you attempt to start the
engine after changing the ignition mode
to “ACC” or “ON” by pressing the engine
switch.
61MM0A182
(1) Immobilizer/keyless push start sys-
tem warning light (blinks)
(2) Master warning indicator light (blinks)
NOTE:
• If the warning is given, locate the remote
controller as soon as possible.
• Any attempt to start the engine will fail
while the warning is active. The mes-
sage appearing on the information dis-
play in the instrument cluster will also
indicate this condition. Refer to “Informa-
tion display” in the “BEFORE DRIVING”
section for details.
• Normally, the immobilizer/keyless push
start system warning light should go out
and the master warning indicator light
should stop blinking shortly after the
remote controller is brought back inside
the vehicle. If they remain lit and blink-
ing, change the ignition mode to “LOCK”
(OFF) by pressing the engine switch and
then perform the engine starting opera-
tion. Refer to “Starting the Engine” in this
section.
• Always keep the remote controller with
you as the driver.
,QWHULRU:RUNDEOH$UHDIRU(QJLQH
6WDUWLQJ,JQLWLRQ0RGH6HOHFWLRQ
DQG5HPRWH&RQWUROOHU2XWVLGH
:DUQLQJ
61MM0B002
(1) Interior workable area
The interior workable area for these func-
tions is defined as all the interior spaces
except for the space above the instrument
panel.
NOTE:
• Even when the remote controller is in the
“interior workable area”, if it is in any of
the following conditions, you may not be
able to start the engine or select the igni-
tion modes, and the remote controller
outside warning may be given.
– The remote controller’s battery is low.
– The remote controller is affected by
strong radio signals or noise.
– The remote controller is in contact with
or covered by a metallic object.
(1)
(2)
(1)

Downloaded from www.Manualslib.com manuals search engine 23(5$7,1*<2859(+,&/(
06(
– The remote controller is in stowage
like the glove box or a door pocket.
– The remote controller is in the sun
visor pocket or on the floor.
• Even when the remote controller is out-
side the “interior workable” area, if it is in
any of the following conditions, you may
be able to start the engine or select the
ignition mode. The “remote controller
outside” warning may not be given at
that time.
– The remote controller is outside the
vehicle but very close to a door.
– The remote controller is on the instru-
ment panel.
3DUNLQJ%UDNH/HYHU
64MS185
(1) To set
(2) To release
(3) To release
The parking brake lever is located between
the seats. To set the parking brake, hold
the brake pedal down and pull the parking
brake lever all the way up. To release the
parking brake, hold the brake pedal down,
pull up slightly on the parking brake lever,
push the button on the end of the lever
with your thumb, and lower the lever to its
original position.
(2)
(3) (1)
(;$03/(
:$ 5 1 , 1 *

Downloaded from www.Manualslib.com manuals search engine 23(5$7,1*<2859(+,&/(
06(
tion. In this case, always let the engine
idle before stop it.6WDUWLQJD&ROGDQG:DUP(QJLQH&ROGHQJLQH
Depress the clutch and brake pedals fully
and press the engine switch to crank the
engine. If the glow plug indicator light
comes on, the engine will start automati-
cally after the glow plug indicator light goes
off or 10 seconds past.
:DUPHQJLQH
Crank the engine by pressing the engine
switch to change the ignition mode to
“START”.&DXWLRQ ZKHQ VWRSSLQJ WKH HQJLQH ZLWK
WXUERFKDUJHU
When stopping the engine after climbing or
high speed driving, let the engine idle for
about one minute or more (if it is not pro-
hibited) to cool down the turbocharger and
engine oil. This is to prevent the engine oil
from over-deteriorating. Deteriorated
engine oil will damage the bearings of the
turbocharger.
5HVWDUWLQJ GLHVHO HQJLQH DIWHU IXHO
HPSW\VWRS
If the engine stops and the low fuel warn-
ing light and the malfunction indicator light
come on, use the following procedure:
1) Fill the fuel tank.
2) Press the engine switch to change the
ignition mode to “ON” for 5-10 seconds
to feed fuel.
3) Perform above engine starting proce-
dure to start the engine.
If the malfunction indicator light still comes
on after the engine started, there may be
some problem with the engine. Ask your
DXWKRULVHG0DUXWL6X]XNLZRUNVKRS to have
theengine inspected.
,IWKH0$67(5:$51,1*LQGLFDWRUOLJKW
EOLQNVDQGWKHHQJLQHFDQQRWEHVWDUWHG
Your keyless push start system remote
controller may not be sensed as being
within the interior workable area. Try again
after making sure that you have the remote
controller with you. If the engine still can-
not be started, the battery of the remote
controller may be discharged. You mustthen use the following method to be able to
start the engine.
58MST0302
1) Make sure the parking brake is set fully.
2) Shift to “N” (Neutral) and fully depress
the clutch pedal. Hold the clutch and
brake pedals fully depressed.
3) The “PUSH START SWITCH.” mes-
sage will appear on the information dis-
play in the instrument cluster. Press the
engine switch (1).
4) Within about 10 seconds of blinking of
the “MASTER WARNING” indicator
light in the instrument cluster, touch the
engine switch with the lock button end
of the remote controller (2) for about 2
seconds.
NOTE:
• If you still cannot start the engine after
several attempts using the above
NOTICE
'RQRWFUDQNWKHHQJLQHIRUPRUH
WKDQVHFRQGVDWDWLPH
,IWKHHQJLQHGRHVQ

Downloaded from www.Manualslib.com manuals search engine 
23(5$7,1*<2859(+,&/(
06(
method, there may be a problem else-
where, such as a low battery. Contact
your DXWKRULVHG 0DUXWL 6X]XNL ZRUNVKRS
forinspection.
• The immobilizer/keyless push start sys-
tem warning light will come on for about
5 seconds while the master warning indi-
cator light is blinking. In addition, the
information display will show a certain
message during this time. Refer to
“Information Display” in the “BEFORE
DRIVING” section for details.
• You may customize the system to cause
the interior buzzer to sound once for the
remote controller out of sensing range
warning. Please contact an DXWKRULVHG
0DUXWL 6X]XNL ZRUNVKRS for the
customization.
• If the battery of the remote controller is
about to be completely discharged, a
message warning this will appear on the
information display when the ignition
mode is changed to “ON” by pressing
the engine switch. For details on replac-
ing the battery, refer to the “Keyless
Push Start System Remote Controller” in
the “BEFORE DRIVING” section.
5HWXUQLQJWKHLJQLWLRQPRGHWR
³/2&.´2))