engine SUZUKI NEXA 2015 1.G Owners Manual
Page 231 of 288
Downloaded from www.Manualslib.com manuals search engine
, 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
& K D Q J L Q J ( Q J L Q H 2 L O D Q G ) L O W H UDrain the engine oil while the engine is still
warm.
64MS151
(1) Engine oil filler cap (D13A engine)
(2) Engine oil filler cap (D16AA engine)
1) Remove the oil filler cap.
2) Place a drain pan under the drain plug.
3) Using a wrench, remove the drain plug
and drain out the engine oil.
60G306
7 L J K W H Q L Q J W R U T X H I R U G U D L Q S O X J
1 P N J P O E I W
4) Reinstall the drain plug
Z L W K Q H Z
gasket.
Tighten the plug with a
wrench to the
specified torque.
5 H S O D F H W K H 2 L O ) L O W H U ) R U ' $ ' L H V H O ( Q J L Q H 0 R G H O
NOTE:
Since special procedures and tools are
required, it is recommended that you trust
this job to your D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S.
1) Using a socket or a ring spanner
remove oil filter housing cover (3).
61M7001
(1) Loosen
(2) Tighten
2) Remove the old oil filter element and
replace it with a new oil filter element.
3) Clean the surface of oil filter cap and
replace the O-ring.4)
Tighten the oil filter housing cover on
the oil filter housing using a socket or
ring spanner to the specified torque.
& $ 8 7 , 2 1
7 K H H Q J L Q H R L O W H P S H U D W X U H P D \ E H
K L J K H Q R X J K W R E X U Q \ R X U I L Q J H U V
Z K H Q W K H G U D L Q S O X J L V O R R V H Q H G : D L W
X Q W L O W K H G U D L Q S O X J L V F R R O H Q R X J K W R
W R X F K Z L W K \ R X U E D U H K D Q G V
(2)
(1)
Open
Close
( ; $ 0 3 / (
: $ 5 1 , 1 *
1 H Z D Q G X V H G R L O F D Q E H K D ] D U G R X V
& K L O G U H Q D Q G S H W V P D \ E H K D U P H G E \
V Z D O O R Z L Q J Q H Z R U X V H G R L O . H H S Q H Z
D Q G X V H G R L O D Q G X V H G R L O I L O W H U V D Z D \
I U R P F K L O G U H Q D Q G S H W V
5 H S H D W H G S U R O R Q J H G F R Q W D F W Z L W K
X V H G H Q J L Q H R L O P D \ F D X V H V N L Q F D Q
F H U
% U L H I F R Q W D F W Z L W K X V H G R L O P D \ L U U L W D W H
V N L Q
7 R P L Q L P L ] H \ R X U H [ S R V X U H W R X V H G
R L O Z H D U D O R Q J V O H H Y H V K L U W D Q G P R L V
W X U H S U R R I J O R Y H V V X F K D V G L V K Z D V K
L Q J J O R Y H V Z K H Q F K D Q J L Q J R L O , I R L O
F R Q W D F W V \ R X U V N L Q Z D V K W K R U R X J K O \
Z L W K V R D S D Q G Z D W H U
/ D X Q G H U D Q \ F O R W K L Q J R U U D J V L I Z H W
Z L W K R L O
5 H F \ F O H R U S U R S H U O \ G L V S R V H R I X V H G
R L O D Q G R L O I L O W H U
(1)
(2)
(3)
( ; $ 0 3 / (
Page 232 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
7 L J K W H Q L Q J W R U T X H I R U R L O I L O W H U
' $ ' L H V H O H Q J L Q H
1 P N J P O E I W
5 H I L O O Z L W K 2 L O D Q G & K H F N I R U / H D N V1) Pour oil through the filler hole and
install the filler cap.
For the approximate capacity of the oil,
refer to the “Capacities” item in the
“SPECIFICATIONS” section.
2) Start the engine and look carefully for
leaks at the oil filter and drain plug. Run
the engine at various speeds for at least
5 minutes.
3) Stop the engine and wait about 5 min-
utes. Check the oil level again and add
oil if necessary. Check for leaks again.
) R U ' $ $ ' L H V H O ( Q J L Q H 0 R G H OSince spec
ial procedures and tools are
requ
ired,
it is recommended that you trust
this job to your
A U T H O R I S E D - A R U T I
3 U Z U K I W O R K S H O P
( Q J L Q H & R R O D Q W 6 H O H F W L R Q R I & R R O D Q WTo m a
inta
in opt
imum performance and
durab
ility of your eng
ine, use MARUTI
Genu
ine Coolant or equ
ivalent
.
Th
is type of coolant
is best for your cool
ing
system as
it:
• Helps mainta
in proper eng
ine tempera-
ture
.
•G
ives proper protect
ion aga
inst freez
ing
and bo
iling.
•G
ives proper protect
ion aga
inst corro-
s
ion and rust
.
Failure to use the proper coolant can dam-
age your cooling system. Your D X W K R U L V H G
0 D U X W L 6 X ] X N L Z R U N V K R S can help you
select the proper coolant.
NOTICE
7 R S U H Y H Q W R L O O H D N D J H P D N H V X U H
W K D W W K H R L O I L O W H U L V W L J K W E X W G R Q R W
R Y H U W L J K W H Q L W
NOTICE
Page 233 of 288
Downloaded from www.Manualslib.com manuals search engine
, 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
& R R O D Q W / H Y H O & K H F NCheck the coolant level at the reservoir
tank, not at the radiator. With the engine
cool, the coolant level should be between
the “FULL” and “LOW” marks. $ G G L Q J & R R O D Q W
61MM0A125
NOTICE
7 R D Y R L G G D P D J L Q J \ R X U F R R O L Q J V \ V
W H P
Page 234 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
If the coolant level is below the “LOW”
mark, more coolant should be added.
When the engine is cool, remove the
degassing tank cap by turning it anticlock-
wise slowly to release any pressure. And
add coolant until the degassing tank level
reaches the “FULL” mark. Never fill the
degassing tank above the “FULL” mark. & R R O D Q W 5 H S O D F H P H Q WSince special procedures are required, we
recommend you take your vehicle to your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S for
coolant replacement.
$ L U & O H D Q H UIf the air cleaner is clogged with dust, there
will be greater intake resistance, resulting
in decreased power output and increased
fuel consumption.
61MM0A126
Unclamp the side clamps and remove the
element from the air cleaner case. If it
appears to be dirty, replace it with a new
one.
Clamp the side clamps securely.
* H D U 2 L O 0 D Q X D O 7 U D Q V D [ O H 2 L OWhen adding gear oil, use gear oil with the
appropriate viscosity and grade as shown
in the chart below.
We highly recommend you use:
“MARUTI * ( 1 8 , 1 ( GEAR OIL : ”
for manual transaxle gear oil.
0 D Q X D O W U D Q V D [ O H R L O
68LM728
* H D U 2 L O / H Y H O & K H F N V S H H G P D Q X D O W U D Q V D [ O H
52LM021
: $ 5 1 , 1 *
, W L V K D ] D U G R X V W R U H P R Y H W K H U H V H U
Y R L U W D Q N F D S G H J D V V L Q J W D Q N F D S I R U
D G L H V H O H Q J L Q H Z K H Q W K H Z D W H U W H P
S H U D W X U H L V K L J K E H F D X V H V F D O G L Q J
I O X L G D Q G V W H D P P D \ E H E O R Z Q R X W
X Q G H U S U H V V X U H : D L W X Q W L O W K H F R R O D Q W
W H P S H U D W X U H K D V O R Z H U H G E H I R U H
U H P R Y L Q J W K H F D S
( ; $ 0 3 / (
C
Fo o-30
-22-20
-4-10
14 32 50 68 86 104010203040
75W-80
(1) ( ; $ 0 3 / (
Page 235 of 288
Downloaded from www.Manualslib.com manuals search engine
, 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
V S H H G P D Q X D O W U D Q V D [ O H
71LS10701
7 R F K H F N W K H J H D U R L O O H Y H O X V H W K H I R O
O R Z L Q J S U R F H G X U H 1) Park the vehicle on a level surface with
the parking brake applied. Then, stop
the engine.
2) Remove the oil filler and level plug.
3) If gear oil flows from the plug hole, the oil
level is correct. Reinstall the plug. If gear
oil does not flow from the plug hole, add
oil through the filler plug hole until oil
flows a little from the plug hole. 7 L J K W H Q L Q J W R U T X H I R U R L O I L O O H U D Q G O H Y H O
S O X J
0 D Q X D O W U D Q V D [ O H R U
1 P N J P O E I W
* H D U 2 L O & K D Q J HSince special procedures, materials and
tools are required, it is recommended that
you trust this job to your D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S.
& $ 8 7 , 2 1
$ I W H U G U L Y L Q J W K H Y H K L F O H W K H J H D U R L O
W H P S H U D W X U H P D \ E H K L J K H Q R X J K W R
E X U Q \ R X : D L W X Q W L O W K H R L O I L O O H U D Q G
O H Y H O S O X J L V F R R O H Q R X J K W R W R X F K
Z L W K \ R X U E D U H K D Q G V E H I R U H L Q V S H F W
L Q J J H D U R L O O H Y H O
(2)
( ; $ 0 3 / (
NOTICE
: K H Q W L J K W H Q L Q J W K H S O X J D S S O \ W K H
I R O O R Z L Q J V H D O L Q J F R P S R X Q G R U
H T X L Y D O H Q W W R W K H S O X J W K U H D G V W R S U H
Y H Q W R L O O H D N D J H
0 $ 5 8 7 , 6 8 = 8 . , % R Q G 1 R
Page 236 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
& O X W F K 3 H G D O ) O X L G & R Q W U R O & O X W F K
64MS141
Check the clutch pedal for smooth opera-
tion and clutch fluid level from time to time.
If clutch dragging is felt with the pedal fully
depressed, have the clutch inspected by
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S. If the
clutch fluid level is near the “MIN” triangle
mark, fill it up to the “MAX” triangle mark
with MARUTI genuine brake fluid.
) X H O ) L O W H U
64MS175
The fuel filter works as a water sedimentor
as well.
Drain water according to the Periodic
Maintenance Schedule. To drain water:
1) Place a pan or ample rag under the fuel
filter drain nozzle.
2) Loosen the drain screw (1). The water
will be drained.
3) Tighten the drain screw when the water
changes to the diesel fuel.
7 L J K W H Q L Q J W R U T X H I R U G U D L Q V F U H Z
1 P N J P O E I W
% U D N H V % U D N H ) O X L G
64MS141
Check the brake fluid level by looking at
the reservoir in the engine compartment.
Check that the fluid level is between the
“MAX” and “MIN” triangle mark. If the
brake fluid level is near the “MIN” triangle
mark, fill it up to the “MAX” triangle mark
with MARUTI GENUINE BRAKE FLUID.
MAX
MIN
(1)
( ; $ 0 3 / (
MAX
MIN
Page 237 of 288
Downloaded from www.Manualslib.com manuals search engine
, 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
NOTE:With disc brakes, the fluid level can be
expected to gradually fall as the brake pads
wear. % U D N H 3 H G D OCheck if the brake pedal stops at the regular
height without spongy feeling when you
depress it. If not, have the brake system
inspected by your D X W K R U L V H G 0 D U X W L 6 X ] X N L
Z R U N V K R S. If you doubt the brake pedal for
the regular height, check it as follows:
54G108
3 H G D O W R I O R R U F D U S H W P L Q L P X P G L V
W D Q F H ³ D ´ P P L Q With the engine running, measure the dis-
tance between the brake pedal and floor
carpet when the pedal is depressed with
approximately 30 kg (66 lbs) of force. The
minimum distance required is as specified.
Since your vehicle’s brake system is self-
adjusting, there is no need for pedal adjust-
ment.
If the pedal to floor carpet distance as mea-
sured above is less than the minimum dis-
tance required, have your vehicle inspected
by your D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S.NOTE:When measuring the distance between the
brake pedal and floor wall, be sure not to
include the floor mat or rubber on the floor
wall in your measurement.
: $ 5 1 , 1 *
) D L O X U H W R I R O O R Z W K H J X L G H O L Q H V E H O R Z
F D Q U H V X O W L Q S H U V R Q D O L Q M X U \ R U V H U L
R X V G D P D J H W R W K H E U D N H V \ V W H P
Page 238 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
3 D U N L Q J % U D N H
54G109
5 D W F K H W W R R W K V S H F L I L F D W L R Q
Page 239 of 288
Downloaded from www.Manualslib.com manuals search engine
, 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
7 L U H V
74LHT0704
The front and rear tire pressure specifica-
tions for your vehicle are listed on the Tire
Information Label. Both the front and rear
tires should have the specified tire pressure.
Note that the value does not apply to the
spare tire, if equipped.
7 L U H , Q V S H F W L R QInspect your vehicle’s tires at least once a
month by performing the following checks:1) Measure the tire pressure with a tire
gauge. Adjust the pressure if necessary.
Remember to check the spare tire, too.
54G136
(1) Tread wear indicator
(2) Indicator location mark2) Check that the depth of the tread groove
is more than 1.6 mm (0.06 in.). To help
you check this, the tires have molded-in
tread wear indicators in the grooves.
When the indicators appear on the tread
surface, the remaining depth of the tread
is 1.6 mm (0.06 in.) or less and the tire
should be replaced.
3)Check for abnormal wear, cracks and
damage. Any tires with cracks or other
damage should be replaced. If any tires
show abnormal wear, have them
inspected by your
D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S
.
( ; $ 0 3 / (
: $ 5 1 , 1 *
Page 240 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
4) Check for loose wheel nuts.
5) Check that there are no nails, stones or
other objects sticking into the tires.
7 L U H 5 R W D W L R Q W L U H U R W D W L R Q
80JK040
If your vehicle is equipped with a spare tire
which is a different wheel type than the
wheels on the vehicle, you must use a 4-
tire rotation as shown in the example
below.
W L U H U R W D W L R Q
54G114
To avoid uneven wear of your tires and to
prolong their life, rotate the tires as illus-
trated. Tires should be rotated every 10000
km (6000 miles). After rotation, adjust front
and rear tire pressures to the specification
listed on your vehicle’s Tire Information
Label.
& $ 8 7 , 2 1
+ L W W L Q J F X U E V D Q G U X Q Q L Q J R Y H U U R F N V
F D Q G D P D J H W L U H V D Q G D I I H F W Z K H H O
D O L J Q P H Q W % H V X U H W R K D Y H W L U H V D Q G
Z K H H O D O L J Q P H Q W F K H F N H G S H U L R G L
F D O O \ E \ \ R X U D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S
: $ 5 1 , 1 *