engine SUZUKI NEXA 2015 1.G Owners Manual

Downloaded from www.Manualslib.com manuals search engine 7-18
INSPECTION AND MAINTENANCE
64MS0-74E
Wheel AlignmentIn case of abnormal tyre wear or pull
ing
towards one s
ide, have the wheel al
igned

at
AUTHORISED-ARUTI3UZUKI.%8!DEALER
WORKSHOP
Tubeless Tyres (If equipped)The veh
icle
is equ
ipped w
ith Tubeless
Tyres
. In tubeless tyre, a th
in layer of butyl
rubber
is used for l
ining the
inside of the
tubeless tyre
. Th
is layer
is to prevent a
ir
loss and fulf
illing the purpose of tube
. The
a
ir pressure
is ma
inta
ined by the seal
ing
between tyre bead and wheel r
im. Tube-
less tyres are hav
ing advantage of slow a
ir
loss and prevent
ing sudden deflat
ion wh
ile
dr
iving.Care and maintenance tips for tubeless
tyres
1) Always ma
inta
in recommended
inflat
ion
pressure
. Dr
iving cont
inuously at low
inflat
ion pressure can lead to tyre dam-
age.
2) In case any leakage
is found, check for
any na
il penetrat
ion/valve core dam-
age or r
im bent
. Damaged wheel must
not be used
.
3) In case tyre has run at low pressure,
it
must be
inspected for any defect
.
4) Whenever new tyre
is fitted, replace the
valve
.
5) If cont
inuous h
igh speed dr
iving
is
requ
ired,
increase tyres pressure by 5
ps
i over recommended
inflat
ion pres-
sure
.
6) Never run the tyre beyond TWI (Tread
wear
indicator)
. The tyre
is recommen-
ded to be replaced when the rema
ining
tread has worn to th
is po
int. The
indica-
tors are spaced across the tread
around the tyre marked by a tr
iangular
symbol (TWI)
.
7) Always prefer tubeless tyre mount
ing
mach
ine. In case of manual mount
ing-
tyre/wheel r
im damage may occur
.
8)
In case of any problem, please get
in
touch w
ith
AUTHORISED -ARUTI 3UZUKI
WORKSHOP
Battery
WA R N I N G
• Batteries produce flammable
hydrogen gas. Keep flames and
sparks away from the battery or an
explosion may occur. Never smoke
when working in the vicinity of the
battery.
• When checking or servicing the
battery, disconnect the negative
cable. Be careful not to cause a
short circuit by allowing metal
objects to contact the battery posts
and the vehicle at the same time.
• To avoid harm to yourself or dam-
age to your vehicle or battery, fol-
low the jump starting instructions
in the “EMERGENCY SERVICE”
section of this manual if it is neces-
sary to jump start your vehicle.
• Diluted sulfuric acid spilled from
battery can cause blindness or
severe burns. Use proper eye pro-
tection and gloves. Flush eyes or
body with ample water and get
medical care immediately if suf-
fered. Keep batteries out of the
reach of children.
Wheel BalancingIf the veh
icle v
ibrates abnormally on

smooth road, have the wheel balanced at

AUTHORISED-ARUTI3UZUKIWORKSHOP

Downloaded from www.Manualslib.com manuals search engine ,163(&7,21$1'0$,17(1$1&(
06(
76MS006
7he level of the battery solution mustbe
kept between the upper level line (1)
and lower level line (2) at all times. If the
level is found to be below the lower level
line (2), add distilled water to the upper
level line (1). You should periodically check
the battery, battery terminals, and battery
hold-down bracket for corrosion. Remove
corrosion using a stiff brush and ammonia
mixed with water, or baking soda mixed
with water. After removing corrosion, rinse
with clean water.
If your vehicle is not going to be driven for
a month or longer, disconnect the cable
from the negative terminal of the battery to
help prevent discharge.5HSODFHPHQWRIWKHEDWWHU\
)RU'$'LHVHO(QJLQH0RGHO
64MS160
NOTE:
(For D13A Diesel Engine Model)
To approach the battery, remove the suc-
tion pipe (1).)RU'$$'LHVHO(QJLQH0RGHO
61MS2A006
NOTE:
(For D16AA Diesel Engine Model)
To approach the battery, loosen the bolts,
push the locks and remove the suction
pipe (1).
(;$03/(
(1)
(;$03/(
(1)
(;$03/(



Downloaded from www.Manualslib.com manuals search engine 
,163(&7,21$1'0$,17(1$1&(
06(
51KM039
To remove the battery:
1) Disconnect the negative cable (1).
2) Disconnect the positive cable (2).
3) Remove the bracket bolt (3) and
remove the bracket (4).
4) Remove the battery.
To install the battery:
1) Install the battery in the reverse order of
removal.
64MS176
NOTE:
When putting the battery in the battery tray,
make sure the recess on the terminal side
bottom of the battery engages with the
convex portion of the tray.
2) Tighten the bracket bolt and battery
cables securely.
NOTE:
When the battery is disconnected, some of
the vehicle’s function will be initialized and/
or deactivated.
These function are required to reset after
the battery is reconnected.
)XVHVYour vehicle has three types of fuses, as
described below:
0DLQIXVH
The main fuse takes current directly from
the battery.
3ULPDU\IXVHV
These fuses are between the main fuse
and individual fuses, and are for electrical
load groups.
,QGLYLGXDOIXVHV
These fuses are for individual electrical cir-
cuits.
To remove a fuse, use the fuse puller (1)
provided in the fuse cover.
64MS198
(1)
(2)
(3)
(4)
(;$03/(
(;$03/(
(1)

Downloaded from www.Manualslib.com manuals search engine ,163(&7,21$1'0$,17(1$1&(
06(
)XVHVLQWKH(QJLQH&RPSDUWPHQW
61MM0B068
64MS177
The main fuse, primary fuses and some of the
individual fuses are located in the engine
compartment. If the main fuse blows, no elec-
trical component will function. If a primary fuse
blows, no electrical component in the corre-
sponding load group will function. When
replacing the main fuse, a primary fuse or an
individual fuse, use a 0DUXWL *HQXLQH3DUWTo
remove a fuse, use the fuse puller provided in
the fuse box. The amperage of eachfuse is
shown in the back of the fuse boxcover.
(6)
(7) (1)
(2)
(3)
(4)
(5)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(17)(18)
(19)
(20)
(21)
(22)
(23)(24)
(25)
(26)
(27)
(28)(29)
(30)
(31)
(32)
(33)
(34)
(35)
0$,1)86(35,0$5<)86(
(1) 60 A FL7
(2) 80 A FL6
(3)
100 A
FL5
(4)
80 A
FL4
(5)
100 A
FL3
(6)
100 A
FL2
(7)
120 A
FL1
(8) 7.5 AIgnition-1 signal 2 (D16AA)
(9) 30 A Radiator fan 2
(10) 20 A Front fog light
(11) 7.5 A Headlight 2
(12) 25 A ABS control module
(13) 25 A Headlight
(14) 30 A Back up
(15) 40 A Ignition switch
(16) 40 A ABS motor
(17) 30 A Starting motor
(18) 30 A Radiator fan
(19) 30 A FI main
(20) 20 A Fuel pump
(21) 10 A Air compressor
(22) 7.5 A ECM (D13A)
(23) 30 A Blower fan
(24) 10 A FI 2 (D13A)
(25) 20 A INJ DRV (D13A)
(26) 7.5 A Starting signal
(27) 15 A Headlight (Left)
(28) 15 A Headlight high (Left)
(29) 7.5 A FI 2 (D16AA)
(30) 20 A INJ DRV (D16AA)
(31) 15 A FI 3 (D16AA)
(32) 15 A Headlight (Right)
(33) 15 A Headlight high (Right)
(34) 50 A Ignition switch 2
(35) 50 A Battery

Downloaded from www.Manualslib.com manuals search engine 
,163(&7,21$1'0$,17(1$1&(
06(
60G111
NOTE:Make sure that the fuse box always carries
spare fuses.
)XVHVXQGHUWKH'DVK%RDUG
64MS181
64MS112
NOTE:
To approach the fuses, remove the clips
(1) by prying it off with a flat blade screw-
driver as shown in the illustration, then
remove the cover (2).
68LM701
:$ 5 1 , 1 *
,IWKHPDLQIXVHRUDSULPDU\IXVH
EORZVEHVXUHWRKDYH\RXUYHKLFOH
LQVSHFWHGE\DQ DXWKRULVHG 0DUXWL
6X]XNL ZRUNVKRS$OZD\VXVHD
0DUXWL *HQXLQH 3DUW 1HYHU XVH D
VXLWDEOH VXFK DV D ZLUH HYHQ IRU D
WHPSRUDU\ UHSDLU RU H[WHQVLYH
HOHFWULFDOGDPDJHDQGDILUHFDQUHVXOW
OK
BLOWN
(;$03/(
(1)
(2) (1)
(1)
(12)(10)
(13)
(36) (2) (3) (4)
(5) (6) (7) (8) (9)
(11) (14) (15)
(16) (17) (18) (19) (20) (21) (22)
(23) (24) (25) (26) (27) (28) (29)
(30) (31) (32) (33) (34) (35)
(;$03/(

Downloaded from www.Manualslib.com manuals search engine 7-23INSPECTION AND MAINTENANCE
64MS0-74E
*Feature not available in the vehicle.
81A283
PRIMARY FUSE
(1) – Blank
(2) 20 A Power window timer
(3) 15 A Steering lock
(4) 20 A Rear defogger(5)
20 A
Sunroof*
(6)
10 A
DRL*
(7)
10 A
Heated mirror*
(8) 7.5 A Starting signal
(9) 15 A Accessory socket 2
(10) 30 A Power window
(11) 10 A Hazard
(12) 7.5 A BCM
(13) 15 A Ignition coil
(14) 10 A ABS control module
(15) 15 A Accessory socket
(16)
10 A
A-STOP controller*
(17) 15 A Horn
(18) 10 A Stop light
(19) 10 A Air bag
(20) 10 A Back-up light
(21) 15 A Wiper / Washer
(22) 30 A Front wiper
(23) 10 A Dome light(24)
15 A
4WD*
(25)
7.5 A
RR fog lamp*
(26) – Blank
(27) 7.5 A Ignition-1 signal
(28) 15 A Radio 2
(29) 10 A Accessory socket 3
(30) 15 A Radio
(31) 10 A Tail lamp
(32) 20 A D/L
(33) 7.5 A Cruise control
(34) 10 A Meter
(35) 7.5 A Ignition-2 signal
(36)
20 A
Seat heater*
WA R N I N G
Always be sure to replace a blown
fuse with a fuse of the correct amper-
age. Never use a substitute such as
aluminum foil or wire to replace a
blown fuse. If you replace a fuse and
the new one blows in a short period of
time, you may have a major electrical
problem. Have your vehicle inspected
immediately by your DXWKRULVHG
0DUXWL6X]XNLZRUNVKRS.
BLOWN OK

Downloaded from www.Manualslib.com manuals search engine 
,163(&7,21$1'0$,17(1$1&(
06(
+HDGOLJKW$LPLQJSince special procedures are required, we
recommend you take your vehicle to your
DXWKRULVHG 0DUXWL 6X]XNL ZRUNVKRSfor
headlight alignment.
%XOE5HSODFHPHQW
+HDGOLJKWV'LVFKDUJHKHDGOLJKWVSince special procedures are required, we
recommend you take your vehicle to your
DXWKRULVHG 0DUXWL 6X]XNL ZRUNVKRSfor
bulb replacement.
61MM0A031
&$87,21

Downloaded from www.Manualslib.com manuals search engine ,163(&7,21$1'0$,17(1$1&(
06(
+DORJHQKHDGOLJKWV
61MM0B073
61MM0B074
1) Open the engine hood. Disconnect the
coupler (2). Remove the sealing rubber
(3).
64MS161
2) Push the retaining spring (4) forward
and unhook it. Then remove the bulb
(5). Install a new bulb in the reverse
order of removal.
64MS162
NOTE:
You can see the position of retaining spring
from the hole of headlight.
(1)
(3)(2)
(4)
(5)
(;$03/(

Downloaded from www.Manualslib.com manuals search engine 
,163(&7,21$1'0$,17(1$1&(
06(
6LGH7XUQ6LJQDO/LJKWLIHTXLSSHG
76MH0A006
1) Remove the light housing (1) by sliding
to left with your finger.
76MH0A007
2) Turn the bulb holder (2) clockwise and
pull it out from the light housing.
76MH0A008
(4) Removal
(5) Install
3) To remove and install the bulb of the
turn signal light (3), simply pull out or
push in the bulb.
)URQW7XUQ6LJQDO/LJKW
)URQW3RVLWLRQ/LJKW(Vehicle with the halogen headlights)
61MM0A030
(1)
(2)
(3)
(4)
(5)
(2)
(1)

Downloaded from www.Manualslib.com manuals search engine ,163(&7,21$1'0$,17(1$1&(
06(
61MM0B077
1) Open the engine hood. To remove the
bulb holder of the front turn signal light
(1) or the front position light (2) from the
light housing, turn the holder counter-
clockwise and pull it out.
61MM0B078
(3) Removal
(4) Install
2) To remove the bulb of the front turn sig-
nal light (1) from the bulb holder, push in
the bulb and turn it counterclockwise. To
install a new bulb, push it in and turn it
clockwise.
To remove and install the bulb of the
front position light (2), simply pull out or
push in the bulb.
9HKLFOHZLWKWKHGLVFKDUJHKHDGOLJKWV
61MM0A091
To replace the bulb of the front turn signal
light (1), follow the procedure for the front
turn signal light bulb replacement of the
vehicle with the halogen headlights.NOTE:
Position function in discharge headlamp is
LED type, which is non replaceable.
(2)(1)
(2)
(1) (3)
(4)
(;$03/(
(1)