remote start SUZUKI NEXA 2015 1.G Owners Manual
Page 20 of 288
Downloaded from www.Manualslib.com manuals search engine 2-1BEFORE DRIVING
64MS0-74E
Keys
54G489
Your vehicle comes with a pair of identical
keys. Keep the spare key in a safe place.
One key can open all of the locks on the
vehicle.
The key identification number is stamped
on a metal tag provided with the keys or on
the keys. Keep the tag (if equipped) in a
safe place. If you lose your keys, you will
need this number to have new keys made.
Write the number below for your future ref-
erence.
Immobilizer System This system is designed to help prevent
vehicle theft by electronically disabling the
engine starting system.
The engine can be started only with your
vehicle’s original immobilizer ignition key
or keyless push start system remote con-
troller which has an electronic identification
code programmed into it. The key or
remote controller communicates the identi-
fication code to the vehicle when the igni-
tion switch is turned to the “ON” position or
the engine switch is pressed to change the
ignition mode to ON. If you need to make
spare keys or remote controllers, see your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S. The
vehicle must be programmed with the
correct identification code for the spare.
A key made by an ordinary locksmith will
not start the engine.
80JM122
If the immobilizer/keyless push start sys-
tem warning light blinks when the ignition
switch is in the “ON” position or the ignition
mode is ON, the engine will not start.
NOTE:If the immobilizer/keyless push start sys-
tem warning light blinks or comes on, a
message may be shown on the information
display.
If the light still blinks after the ignition
switch is turned back to the “ON” position,
there may be something wrong with your
key or with the immobilizer system. Ask
your D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S
to have the system inspected.
For vehicles with keyless push start
system
If this light blinks, change the ignition mode
to “LOCK” (OFF), then change back to
“ON”. Also refer to “If the master warning
indicator light blinks and the engine cannot
be started” in “Starting the Engine (Vehicle
with Keyless Push Start System)” in the
“OPERATING YOUR VEHICLE” section.
If the light still blinks after the ignition mode
is changed back to “ON”, there may be
something wrong with your key or with the
immobilizer system. Ask your D X W K R U L V
H G 0 D U X W L 6 X ] X N L Z R U N V K R S to have the
system inspected.
The immobilizer/keyless push start system
warning light may also blinks if the remote
controller is not in the vehicle when you KEY NUMBER:
EXAMPLE
For vehicles without keyless push start
system
If this light blinks, turn the ignition switch to
the “LOCK” position, then turn it back to
the “ON” position.
Page 21 of 288
Downloaded from www.Manualslib.com manuals search engine 2-2
BEFORE DRIVING
64MS0-74E
close the door or attempt to start the
engine.NOTE:
• If you lose your immobilizer ignition key
or remote controller, see your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S as
soon as possible to have the lost one
deactivated, then have the new key or
remote controller made by them.
• If you own other vehicles with immobi-
lizer keys, keep those keys away from
the ignition switch or the engine switch
when using your Vehicle, or the engine
may not start because they may interfere
with your vehicle’s immobilizer system.
• If you attach any metal objects to the
immobilizer key or remote controller, it
may not start the engine.
Ignition Key Reminder (if equipped)A buzzer sounds intermittently to remind
you to remove the ignition key if it is in the
ignition switch when the driver’s door is
opened.
NOTICE
The immobilizer key and remote con-
troller are sensitive electronic instru-
ments. To avoid damaging them:
• Do not expose them to impacts,
moisture or high temperature such
as on the dashboard under direct
sunlight.
• Keep them away from magnetic
objects.
Page 23 of 288
Downloaded from www.Manualslib.com manuals search engine 2-4
BEFORE DRIVING
64MS0-74E
NOTE:
You can switch the function that unlocks all
doors from twice operations to once opera-
tion, and vice versa, via the setting mode
of the information display. For details on
how to use the information display, refer to
“Information Display” in this section.
To unlock the driver’s door only, insert the
key in that door lock and turn the top of the
key toward the front of the vehicle once.
64MS021
(1) LOCK
(2) UNLOCK
You can also lock or unlock all doors by
depressing the front or rear of the switch,
(3) respectively.NOTE:
• You can also lock or unlock all doors by
operating the transmitter or remote con-
troller. Refer to “Keyless Push Start Sys-
tem Remote Controller/Keyless Entry
System Transmitter” in this section.
• If your vehicle is equipped with the key-
less push start system, you can also lock
or unlock all doors by pushing the request
switch. Refer to “Keyless Push Start Sys-
tem Remote Controller/Keyless Entry
System Transmitter” in this section.NOTE:
• All doors are automatically unlocked
when you turn the ignition switch to the
“LOCK” position and pull out the key, or
press the engine switch to change the
ignition mode to LOCK (OFF).
• All doors are automatically locked for
safety when the vehicle speed reaches
15 km/h.
• You can change the automatic locking or
unlocking function mentioned above via
the setting mode of the information dis-
play. For details on how to use the infor-
mation display, refer to “Information
Display” in this section.
Child-Proof Locks (rear door)
61MM0A046
(1) Lock position
(2) Unlock position
Each of the rear doors is equipped with a
child-proof lock which can be used to help
prevent unwanted opening of the door
from inside the vehicle. When the lock
lever is in the lock position (1), the rear
door can only be opened from outside.
When the lock lever is in the unlock posi-
tion (2), the rear door can be opened from
inside or outside.
EXAMPLE
(1)
(2)
(3)
WA R N I N G
Be sure to place the child-proof lock
in the lock position whenever chil-
dren are seated in the rear.
EXAMPLE
Page 24 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
If you cannot unlatch the tailgate by pushing
the unlatch switch (1) due to a discharged
battery or malfunction, follow the proce-
dures below to unlatch the tailgate from
inside the vehicle.
1) Remove the luggage compartment
cover (if equipped) and fold the rear seat
forward for easier access. Refer to
“Folding Rear Seats” section for details
on how to fold the rear seat forward.
2) Push open the tailgate from inside by
pushing up on the emergency lever (2)
using a flat blade screwdriver or the jack
handle. The tailgate will be latched again
by closing the tailgate simply.
68LM246
If the tailgate cannot be unlatched by push-
ing the unlatch switch (1), have the vehicle
inspected by your D X W K R U L V H G 0 D U X W L 6 X ] X N L
Z R U N V K R S
. H \ O H V V 3 X V K 6 W D U W 6 \ V W H P 5 H P R W H
& R Q W U R O O H U . H \ O H V V ( Q W U \ 6 \ V W H P
7 U D Q V P L W W H U
64MS022
Your vehicle is equipped with either a key-
less push start system remote controller
(Type A) or a keyless entry system trans-
mitter (Type B). The remote controller has
a keyless entry system and a keyless push
start system. The transmitter has only a
keyless entry system. For details, refer to
the following explanations.
: $ 5 1 , 1 *
$ O Z D \ V P D N H V X U H W K D W W K H W D L O J D W H L V
F O R V H G D Q G O D W F K H G V H F X U H O \ & R P
S O H W H O \ F O R V L Q J W K H W D L O J D W H K H O S V S U H
Y H Q W R F F X S D Q W V I U R P E H L Q J W K U R Z Q
I U R P W K H Y H K L F O H L Q W K H H Y H Q W R I D Q
D F F L G H Q W & R P S O H W H O \ F O R V L Q J L W D O V R
K H O S V N H H S H [ K D X V W J D V H V I U R P H Q W H U
L Q J W K H Y H K L F O H
& $ 8 7 , 2 1
Page 25 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
. H \ O H V V 3 X V K 6 W D U W 6 \ V W H P 5 H P R W H
& R Q W U R O O H U 7 \ S H $ The remote controller enables the follow-
ing operations:
• You can lock or unlock the doors by
operating the LOCK/UNLOCK buttons
on the remote controller. Refer to the
explanation in this section.
• You can lock or unlock the doors by
pushing the request switch. For details,
refer to the explanation in this section.
• You can start the engine without using
an ignition key. For details, refer to
“Engine Switch” in the
Page 27 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
. H \ O H V V X Q O R F N L Q J O R F N L Q J X V L Q J W K H
U H T X H V W V Z L W F K H V
64MS134
When the remote controller is within the
operating range described in this section,
you can lock or unlock the doors (including
the tailgate) by pushing the request switch
(1) on the driver’s door handle, front pas-
senger’s door handle or tailgate.
To lock all doors when all doors are
unlocked:
• To lock all doors, push one of the
request switches once.
The turn signal lights will flash once and
the siren will sound once when the doors
are locked.
To unlock a door or all doors:
• Push one of the request switches once
to unlock only one door.
• Push one of the request switches twice
to unlock all doors.NOTE:
You can switch the function that unlocks all
doors from twice operations to once opera-
tion, and vice versa, via the setting mode
of the information display. For details on
how to use the information display, refer to
“Information Display” in this section.
When the doors are unlocked:
• The turn signal lights will flash twice and
the siren will sound twice.
• If the interior light switch is in the door
position, the interior light will turn on for
about 15 seconds and then fade out. If
you press the engine switch during this
time, the light will start to fade out imme-
diately.
Be sure the doors are locked after you
operate the request switch to lock the
doors.NOTE:
• If you lock the doors using the request
switch when the engine hood is open,
the siren will sound 3 times to remind
you.
• If the security system was triggered due
to an unauthorized entry into the vehicle
and then you unlock the doors using the
request switch, the siren will sound 4
times to remind you. If this happens,
check whether your vehicle has been
broken into while you were away from it.
• You can set whether the siren sounds
when locking or unlocking the door(s) via
the setting mode of the information dis-
play. For details on how to use the infor-
mation display, refer to “Information
Display” in this section.NOTE:• The door locks cannot be operated by
the request switch under the following
conditions:
– If any door is open or is not completely
closed.
– If the ignition mode is other than LOCK
(OFF).
• If no doors are opened within about 30
seconds after unlocking the doors by
pushing the request switch, the doors will
be locked again automatically.
(1)
( ; $ 0 3 / (
NOTICE
Page 28 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
80J056
(1) 80 cm (2 1/2 feet)
When the remote controller is within
approximately 80 cm (2 1/2 feet) from a
front door handle or the tailgate switch, you
can lock or unlock the doors by pushing
the request switch.
NOTE:
• If the remote controller is outside the
request switch operating range
described above, you will not be able to
operate the request switch.
• If the battery of the remote controller
runs down or there are strong radio
waves or noise, the request switch oper-
ating range may be reduced or the
remote controller may be inoperative.
• If the remote controller is too close to the
door glass, the request switches may not
operate.• If a spare remote controller is in the vehi-
cle, the request switches may not oper-
ate normally.
• The remote controller will only operate a
request switch if it is within the switch’s
operating range. For example, if the
remote controller is within the operating
range of the driver’s door request switch
but not the front passenger’s door
request switch or the tailgate request
switch, the driver’s door switch can be
operated but the front passenger’s door
switch or tailgate switch cannot be oper-
ated.
• Avoid operations of switch with sharp
objects.
NOTE:
The keyless push start system may not
function correctly in certain environments
or under certain operating conditions such
as the following:• When there are strong signals coming
from a television, power station or a cel-
lular phone.
• When the remote controller is in contact
with or covered by a metal object.
• When a radio wave type remote keyless
entry is used nearby.
• When the remote controller is placed
near an electronic device such as per-
sonal computer.
Some additional precautions you should
take and information you should be aware
of are:
• Make sure the key is stowed in the
remote controller. If the remote controller
becomes unreliable, you will not be able
to lock or unlock the doors.
• Be sure that the driver always carries the
remote controller.
•If you lose one of the remote controllers,
ask your
D X W K R U L V H G 0 D U X W L 6 X ] X N L
Z R U N V K R S as soon as possible for a
replacement. Be sure to have your
dealer program the
new remote
controller code in your vehi-cle’s
memory so that the old code is
erased.
• You can use up to four remote controllers
and the keys for your vehicle. Ask your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S
for
details.
• The battery life of the remote controller is
about two years, but it can vary depend-
ing on usage conditions.
(1)
(1)(1)
( ; $ 0 3 / (
NOTICE
7 K H U H P R W H F R Q W U R O O H U L V D V H Q V L W L Y H
H O H F W U R Q L F L Q V W U X P H Q W 7 R D Y R L G G D P
D J L Q J W K H U H P R W H F R Q W U R O O H U
Page 29 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
57L21016
To stow the key into the remote controller,
push the key in the remote controller until
you hear a click.
68LM247
To remove the key from the remote control-
ler, push the button (A) in the direction of
the arrow and pull the key out from the
remote controller. 5 H T X H V W V Z L W F K Z D U Q L Q J E X ] ] H U
This exterior buzzer beeps for about 2 sec-
onds in the following conditions to warn you
that the request switch is not working:
• The request switch is pressed after all
doors are closed with the ignition mode
changed to “ACC” or “ON” by pressing
the engine switch.
• The request switch is pressed in any of
the following conditions after changing
the ignition mode to “LOCK” (OFF) by
pressing the engine switch.
– The remote controller is left inside the
vehicle.
– Any door (including the tailgate) is
open.
Press the request switch again after doing
the following:
With the ignition mode changed to “LOCK”
(OFF) by pressing the engine switch, bring
out the remote controller if it is inside the
vehicle and check that all doors are com-
pletely closed.
5 H P L Q G H U I X Q F W L R Q
64MS165
If the remote controller is not in the vehicle
under the following conditions, the buzzer
sounds intermittently for about 2 seconds
and the immobilizer/keyless push start sys-
tem warning light on the instrument cluster
blinks:When one or more doors are opened and
all of the doors are later closed with the
ignition mode is other than “LOCK”.
The indicator light will turn off within sev-
eral seconds after the remote controller is
returned to an area of the vehicle other
than the rear luggage area.
If the remote controller is left in the vehicle
and you lock the driver’s door or front pas-
senger’s door as described below, the door
will be automatically unlocked.
• If you open the driver’s door and lock the
door by turning the lock knob forward or
pushing the power door locking switch,
(A)
( ; $ 0 3 / (
Page 34 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
6 H F X U L W \ 6 \ V W H P L I H T X L S S H G The security system is armed in about 5
seconds after you lock all doors (including
the tailgate) by using the keyless entry sys-
tem transmitter, keyless push start system
remote controller or request switch.
Once the system is armed, any attempt to
open a door by using any other means (*)
than the keyless entry system transmitter,
keyless push start system remote control-
ler or request switch, or open the engine
hood, will cause the alarm to be triggered.
* These means include the following:
– The key
– The lock knob on a door
– The central door locking switchAlso, in case that you have set the shock
sensor to enabled state and set sensitivity
of the pre-warning function and full blast
warning function to a level other than 0, the
alarm will be triggered if any attempt is
made to tamper with the vehicle. The shock
sensor can be selected to enabled or dis-
abled state, and sensitivity of each warning
can be adjusted as desired. To set the
shock sensor, ask your D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S or use the setting mode of
the information display.NOTE:
• The default setting of the shock sensor
is in the disabled state. Set to the
enabled state and adjust sensitivity of
each warning according to your prefer-
ence. For details on how to use the infor-mation display, refer to “Information
Display” in this section.
• Your dealer may have already set the
shock sensor of the vehicle to the
enabled state before you purchase it.
Consult your dealer for further informa-
tion.
NOTE:
• The security system generates alarms
when any of the predetermined condi-
tions is met. However, the system does
not have any function of blocking unau-
thorized entry into the vehicle.
• Always use the keyless entry system
transmitter, keyless push start system
remote controller or request switch to
unlock the doors when the security sys-
tem has been armed. Using a key
instead will trigger the alarm.
• If a person who does not know the secu-
rity system is going to drive the vehicle,
we recommend you explain the system
and its operation to the person, or dis-
able the system beforehand. Mistakenly
triggering the alarm may cause a nui-
sance to others.
• Even if the security system is armed,
you should still be careful to guard
against theft. Do not leave money or
things of value in the vehicle. + R Z W R D U P W K H V H F X U L W \ V \ V W H P
Z K H Q H Q D E O H G
Lock all doors (including the tailgate) using
the keyless entry system transmitter, key-
less push start system remote controller or
request switch. The security system indica-
tor (1) will start blinking rapidly, and the
security system will be armed in about 5
seconds.
While the system is being armed, the indi-
cator continues to blink at intervals of
approximately 2 seconds
61MM0A134
NOTE:
• To prevent the alarm from being acci-
dentally triggered, avoid arming it while
anyone remains inside the vehicle. The
alarm will be triggered if any person
inside opens the door or engine hood, or
swings the vehicle (if the shock sensor is
in the enabled state).
• The security system is not armed when
all doors are locked using the key from
(1)
Page 35 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
outside, or using the door lock knobs or
the central door locking switch from
inside.
• If any door is not operated within approx-
imately 30 seconds after the doors have
been unlocked using the keyless entry
system transmitter, keyless push start
system remote controller or request
switch, the doors are automatically
locked again. When the doors are
locked, the security system will be
armed in about 5 seconds if the system
is in the enabled state.
• If the security system indicator (1) blinks
when the ignition switch is in the “ON”
position or the ignition mode is “ON”,
there may be something wrong with the
security system. Ask your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S to
inspect the system.
+ R Z W R G L V D U P W K H V H F X U L W \ V \ V W H P
Simply unlock the doors using the keyless
entry system transmitter, keyless push
start system remote controller or request
switch. The security system indicator will
go out, indicating that the security system
is disarmed.
+ R Z W R V W R S W K H D O D U P
Should the alarm be triggered accidentally,
unlock the doors using the keyless entry
system transmitter, keyless push start sys-
tem remote controller or request switch, or
insert the key in the ignition switch and turn
it to “ON” position, or press the engineswitch to change the ignition mode to
“ON”. The alarm will then stop.
NOTE:
• Even after the alarm has stopped, if you
lock the doors using the keyless entry
system transmitter, keyless push start
system remote controller or request
switch, the security system will be
rearmed with a delay of about 5 sec-
onds.
• If you disconnect the battery while the
security system is in the armed condition
or the alarm is actually in operation, the
alarm will be re-triggered when the bat-
tery is then reconnected.
• Even after the alarm has stopped at the
end of the predetermined operation time,
it will be triggered again if any of the
doors or engine hood is opened, or the
vehicle feels a shock (if the shock sen-
sor is in the enabled state), without dis-
arming the security system.
& K H F N L Q J Z K H W K H U W K H D O D U P K D V E H H Q
W U L J J H U H G G X U L Q J S D U N L Q J
If the alarm was triggered and you then
turn the ignition switch to “ON” position, or
press the engine switch to change the igni-
tion mode to “ON”, the security system
indicator will blink rapidly for about 8 sec-
onds and a buzzer will beep 4 times during
this period. If this happens, check whether
the vehicle has been broken into while you
were away from it. ( Q D E O L Q J D Q G G L V D E O L Q J W K H V H F X U L W \
V \ V W H P
The security system can be either enabled
or disabled.
: K H Q H Q D E O H G
• If any of the doors are opened without
unlocking by the keyless entry system
transmitter, keyless push start system
remote controller or request switch, all
turn signal lights start to blink and the
interior buzzer beeps intermittently. After
5 seconds, the siren will sound for about
27.5 seconds. The security system indi-
cator continues to blink during this time.
• If the engine hood is opened, all turn sig-
nal lights blink, and the siren sounds for
about 27.5 seconds. The security sys-
tem indicator continues to blink during
this time.
( , I W K H V K R F N V H Q V R U L V L Q W K H H Q D E O H G
V W D W H
• If the vehicle feels a shock, the siren
sounds for about 2 seconds (pre-warn-
ing). If the vehicle continues to feel a
shock, all turn signal lights start to blink
and the interior buzzer beeps intermit-
tently. After 5 seconds, the siren will
sound for about 27.5 seconds (full blast
warning). The security system indicator
continues to blink during this time.
NOTE:
If you set the full blast warning sensitivity
higher than the pre-warning sensitivity in
the setting mode of the information display,
or the vehicle feels such shock as to be