set clock SUZUKI NEXA 2015 1.G Owners Manual

Page 67 of 288

Downloaded from www.Manualslib.com manuals search engine 
%()25('5,9,1*
06(
,QIRUPDWLRQ'LVSOD\The information display is shown when the
ignition switch is in the “ON” position or the
ignition mode is ON.
64MS183
(1) Information display
64MS184
(2) Indicator selector knob
(3) Trip meter selector knob
The information display shows the follow-
ing information.'LVSOD\ $
Clock
'LVSOD\ %
Thermometer
'LVSOD\ &
Warning and indicator messages /
Fuel consumption / Driving range /
Average speed
'LVSOD\ '
Trip meter
'LVSOD\ (
Odometer
64MS181
When the ignition switch is turned to the
“ON” position or the engine switch is
pressed to change the ignition mode to
ON, the message shown in the above illus-
tration will appear on the display for sev-
eral seconds.
Some warning and indicator messages
may appear on the display when the igni-
tion switch is in the “ACC” or “LOCK” posi-
tion, or the ignition mode is ACC or LOCK
(OFF).
&ORFNThe display (A) shows the time.
To set the clock, follow the “Setting mode”
instructions in this section.7KHUPRPHWHUThe display (B) shows the thermometer.
The thermometer indicates the outside
temperature.
61MM0A160
If the outside temperature nears freezing,
the message shown in the above illustra-
tion will appear on the display.
NOTE:
The outside temperature indication is not
the actual outside temperature when driv-
ing at low speed, or when stopped.
(1)(B)
(C) (A)
(D)
(E)
(3)
(2)
(;$03/(

Page 195 of 288

Downloaded from www.Manualslib.com manuals search engine 
27+(5&21752/6$1'(48,30(17
06(
3KRQHUHJLVWUDWLRQ
NOTE:
• Up to 5 phones can be registered.
• To set up a new phone, disconnect the
audio player from the unit. Connect the
audio player again after phone setup is
completed if necessary.
• When failed to establish the pairing
within 120 seconds, the connecting
operation will be canceled. Please try
again or refer to the manual of the phone
in use for how to establish the pairing
with the phone.1) Press the Bluetooth
® setup button (4).
The Bluetooth
® setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH SOUND
knob (1) to select “Setup Bluetooth”, and
press the knob (1) to determine the
selection.
3) Turn the TUNE FOLDER PUSH SOUND
knob (1) to select “Pairing”, and press
the knob (1) to determine the selection.
4) Select “CAR AUDIO” from the Blue-
tooth
® menu of the phone and establish
the pairing.
Refer to the manual of the phone in use
for further information.
5) Enter the Passkey displayed on the unit
to the phone. (For phones with Blue-
tooth
® version 2.1 or above passkey
input is not required.)6) Press the On Hook button (6).
NOTE:
• When selecting “Go Back”, the previous
menu will be displayed.
• When additionally registering a phone,
operate the same step from 1).
5HFHLYLQJDFDOO
Press the Off Hook button (5) to receive a
call.
(QGLQJDFDOO
Press the On Hook button (6) to end a call.
5HMHFWLQJ D FDOO RQO\ IRU VXSSRUWHG
PRGHOV
Press the On Hook button (6) to reject a
incoming call.$GMXVWLQJWKHOLVWHQLQJYROXPH
• Turn the VOL PUSH POWER knob (2)
during a call.
Turning it clockwise increases the vol-
ume; turning it counterclockwise
decreases the volume.
• Press the VOL switch (7) during a call.
Pressing “+” of the switch increases the
volume, pressing “-” of the switch
decreases the volume.
$GMXVWLQJWKHULQJYROXPH
• Turn the VOL PUSH POWER knob (2)
while a call coming in.
Turning it clockwise increases the vol-
ume; turning it counterclockwise
decreases the volume.
• Press the VOL switch (7) during a call.
Pressing “+” of the switch increases the
volume, pressing “-” of the switch
decreases the volume.
$GMXVWLQJWKHFDOORUULQJWRQHYROXPH
Follow the instructions below to adjust the
call or ringtone volume.
1) Press the Bluetooth
® setup button (4).
The Bluetooth
® setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Setup Tele-
phone”, and press the knob (1) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Sound Set-
ting”, and press the knob (1) to deter-
mine the selection.
To use the hands-free function with this
unit, it is required to register the phone
in advance.

Page 265 of 288

Downloaded from www.Manualslib.com manuals search engine 
(0(5*(1&<6(59,&(
06(
-DFNLQJ,QVWUXFWLRQV
75F062
1) Place the vehicle on level, hard ground.
2) Set the parking brake firmly and shift
into “R” (Reverse).
3) Turn on the hazard warning flasher if
your vehicle is near traffic.
4) Block the front and rear of the wheel
diagonally opposite of the wheel being
lifted.5) Place the spare wheel near the wheel
being lifted as shown in the illustration
in case that the jack slips.
54G253
63J10063J101
6) Position the jack at an angle as shown
in the illustration and raise the jack by
turning the jack handle clockwise until
the jack-head groove fits around the
jacking bar beneath the vehicle body.
7) Continue to raise the jack slowly and
smoothly until the tire clears the
ground. Do not raise the vehicle more
than necessary.
:$ 5 1 , 1 *