ECO mode SUZUKI SWIFT 2000 1.G SF310 Service User Guide

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-73
Crankshaft
timing belt
pulleyCKP
sensor
Oscilloscope Waveforms
Waveforms at engine cranking (260 r/min) Waveforms at specified idle speed16 waives
for 10 signals13 waives for
10 signals
30 signal 30 signal 0.5 V / Div.
10 ms / Div.0.5 V / Div.
5 ms / Div.
DTC P0335 CRANKSHAFT POSITION (CKP) SENSOR CIRCUIT MALFUNCTION
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

NO CKP sensor signal for 2 seconds at engine
cranking.
CKP sensor circuit open or short.

Crankshaft timing belt pulley teeth damaged.

CKP sensor malfunction, foreign material being
attached or improper installation.

ECM (PCM) malfunction.
Reference
Connect oscilloscope between terminals C01-23 (+) and C01-24 (–) of ECM (PCM) connector connected to ECM
(PCM) and check CKP sensor signal.
DTC CONFIRMATION PROCEDURE
1) Clear DTC and crank engine for 2 sec.
2) Select “DTC” mode on scan tool and check DTC.

ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-29
5) Install oil seal housing and its gasket.
Install new gasket. Do not reuse gasket removed in disassem-
bly. Oil lip portion of oil seal before installing. Tighten housing
bolts to specification.
After installing oil seal housing, gasket edges might bulge out;
if so, cut them off to make them flush with cylinder block and
oil seal housing.
Tightening Torque
(b): 12 N
.m (1.2 kg-m, 9.0 lb-ft)
6) Install oil pump.
Refer to item “Oil pump” for installation of oil pump.
7) Install flywheel (M / T model) or drive plate (A / T model).
Using special tool, lock flywheel and torque its bolts (1) to spec-
ification.
Special Tool
(A): 09924-17810
Tightening Torque
(c): 78 N
.m (7.8 kg-m, 56.5 lb-ft)
8) Install pistons and connecting rods as previously outlined.
9) Install oil pump strainer and oil pan.
10) Install cylinder head assembly to cylinder block (1).
Before installing cylinder head assembly to cylinder block,
install check valve (2) into oil gallery in cylinder block, directing
slit of valve toward top of cylinder block.
NOTE:
Tighten cylinder head bolts to specified torque as pre-
viously outlined.
Whenever installing cylinder head to new cylinder block,
use following procedure to tighten cylinder head bolts.

Tighten cylinder head bolts to specified torque as pre-
viously outlined and loosen them once till tightening
torque becomes “zero”. And then torque them to specifi-
cation again.
11) Install crankshaft timing belt pulley, timing belt, crankshaft
pulley, water pump pulley, etc., as previously outlined.
12) Install clutch to flywheel (M / T model).
For clutch installation, refer to Section 7C.
13) Install engine with transmission to body as previously outlined.

When not using
SUZUKI scan tool : When using
SUZUKI scan tool :
4. Keep as far apart
as possible
ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13) 6E2-25
4) Install suitable vinyl tube onto injector nozzle to prevent fuel from
splashing out when injecting.
5) Put graduated cylinder under injector as shown.
6) Operate fuel pump and apply fuel pressure to injector as follows:
When using SUZUKI scan tool :
a) Connect SUZUKI scan tool to DLC with ignition switch OFF.
b) Turn ignition switch ON, clear DTC and select “MISC TEST”
mode on SUZUKI scan tool.
c) Turn fuel pump ON by using SUZUKI scan tool.
Special Tool
(A): 09931-76011 (SUZUKI scan tool)
(B): Mass storage cartridge
(C): 09931-76030 (16 / 14 pin DLC cable)
When not using SUZUKI scan tool :
a) Remove fuel pump relay from connector.
b) Connect two terminals of relay connector using service wire
(1) as shown in figure.
CAUTION:
Check to make sure that connection is made between
correct terminals. Wrong connection can cause dam-
age to ECM, wire harness, etc.
c) Turn ignition switch ON.
7) Apply battery voltage (3) to injector (2) for 15 seconds and mea-
sure injected fuel volume with graduated cylinder.
Test each injector two or three times.
If not within specification, replace injector.
Injected fuel volume:
38 – 48 cc / 15 sec. (1.28 / 1.34 – 1.62 / 1.69 US / Imp. oz / 15 sec.)
8) Check fuel leakage from injector nozzle. Do not operate injector
for this check (but fuel pump should be at work).
If fuel leaks (1) more than following specifications, replace.
Fuel leakage (1): Less than 1 drop / min.

IGNITION SYSTEM (SFI FOR G13) 6F1-7
5) Measure secondary coil for resistance.
Secondary coil resistance : 7.6 – 10.2 kΩ at 20C, 68F
If resistance is out of specification, replace ignition coil assem-
bly.
6) Install ignition coil assembly.
7) Tighten ignition coil bolts, and then connect ignition coil coupler.
8) Install high-tension cord to ignition coil assembly while gripping
its cap.
CRANKSHAFT POSITION SENSOR
(CKP SENSOR)
Refer to section 6E2 for removal, inspection and installation.
IGNITION TIMING
NOTE:

Ignition timing is not adjustable. If ignition timing is out of
specification, check system related parts.

Before starting engine, place transmission gear shift lever in
“Neutral” (shift selector lever to “P” range for A / T model),
and set parking brake.
INSPECTION
1) Connect SUZUKI scan tool to DLC with ignition switch OFF.
Special Tool
(A): 09931-76011 (SUZUKI scan tool)
(B): Mass storage cartridge
(C): 09931-76030 (16 / 14 pin DLC cable)
2) Start engine and warm it up to normal operating temperature.
3) Make sure that all of electrical loads except ignition are switched
off.
4) Check to be sure that idle speed is within specification.
(Refer to SECTION 6E2)

7B-4 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
COMPONENTS OPERATION CHART
RangeGearForward
ClutchDirect
ClutchSecond
Brake1st & Reverse
BrakeOne-way
ClutchParking Lock
Pawl
PParking–––****–
RReverse––––
NNeutral––––––
1st––––
D2nd––––
3rd––––
21st––––22nd––––
L1st–––L*2nd––––
: Operated
*: To prevent over-revolution of engine, this 2nd gear is operated only when selector lever is shifted to L range
at a higher than 37 km / h (23 mile / h) (G10 engine model), 40 km / h (25 mile / h) (G13 engine model) speed.
**: When engine is running.

AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-15
CUSTOMER PROBLEM INSPECTION FORM (EXAMPLE)
User name:Model:VIN:
Date of issue:Date Reg.Date of problem:Mileage:
PROBLEM SYMPTOMS
Vehicle does not move (R, D, 2, L range)
No upshift automatically ( 1st to 2nd  2nd to 3rd  2 range  D range)
No downshift automatically ( 3rd to 2nd  2nd to 1st  2 range  D range)
No gear change manually ( 1st  2nd  2nd  3rd)
Automatic shift point too high or too low
Excessive gear change shock (1st / 2nd / 3rd / Reverse)
No kickdown
Transmission slipping in (1st / 2nd / 3rd / Reverse)
Others
VEHICLE / ENVIRONMENTAL CONDITION WHEN PROBLEM OCCURS
Environmental Condition
Weather
Temperature Fair  Cloudy  Rain  Snow  Always  Other
(F/C)  Hot  Warm  Cool  Cold  always
Frequency
y
 Always Sometimes ( times / day, month)  Only once  Under certain
condition
Road Urban  Suburb  Highway  Mountainous  Uphill  Downhill
 Tarmacadam  Grave  Other
Vehicle Condition
Engine &
transmission
 Cold / Warming up phase /  Warmed up
Engine speed ( r / min)transmission
condition
Engine s eed ( r / min)
Throttle opening ( Idle / About % / full)
Vehicle
condition
 At stop /  During driving ( Constant speed  Accelerating  Decelerating)
Right hand cornerLeft hand cornerVehicle speed ( km / h Mile / h)condition Right hand corner  Left hand corner  Vehicle s eed ( km / h Mile / h)
 Other
Malfunction Blink  Always ON  Sometimes ON  Always OFF
indicator lamp Good condition
DiagnosticFirst check:  No code  Malfunction code ( )
trouble codeSecond check:  No code  Malfunction code ( )
NOTE:
The above form is a standard sample. It should be modified according to conditions characteristic of each
market.

*1: For G10 engine model
*2: For G13 engine model
1. PCM
2. Transmission range sensor
3. From ignition switch
4. Shift indicator
5. Backup lamp
6. Terminal arrangement of PCM
coupler (Viewed from harness side)
Gr / Bl (*1), R / B (*2)
AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-21
DTC P0705 TRANSMISSION RANGE SENSOR (SWITCH) CIRCUIT
MALFUNCTION
CIRCUIT DESCRIPTION – Refer to “GENERAL DESCRIPTION” in this section.
DTC DETECTING CONDITION
POSSIBLE CAUSE
DTC will set when either condition A or condition B
occurs.
A: No signal is inputted at ignition switch ON.
B: Multiple signals are inputted while running at higher
than specified vehicle speed with gear in 3rd gear
of “D” range.
“Y”, “Or / B”, “R”, “Or / Y”, “Gr / R”, “Gr” or “Gr / Bl”
(G10 engine model) (“Br / Y”, “W/B”, “R/W”, “W/R”,
“Y/R”, “Y/B” or “R/B” (G13 engine model)) circuit
open or short.

Transmission range sensor malfunction.

Select cable maladjusted.

PCM malfunction.
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Turn ignition switch OFF and then ON.
2) Clear DTC and warm up engine to normal operating temperature.
3) Shift selector lever to each of P, R, N, D, 2 and L ranges and hold it there for longer than 5 seconds each.
4) Check for DTC and if no DTC appears on display, proceed to the next step.
5) Drive vehicle at 40 mph, 60 km / h or more in 3rd gear of “D” range for longer than 5 sec.
6) Stop vehicle and check DTC.

Counter
shaft gear
*1: For G10 engine model
*2: For G13 engine model
1. PCM
2. Output shaft speed sensor
3. Terminal arrangement of PCM coupler
(Viewed from harness side)
7B-24 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
DTC P0720 OUTPUT SPEED SENSOR (A / T VSS) CIRCUIT MALFUNCTION
CIRCUIT DESCRIPTION – Refer to “GENERAL DESCRIPTION” in this section.
DTC DETECTING CONDITION
POSSIBLE CAUSE
No signal inputted while running vehicle with “D” or “2”
range.
“P” or “Bl” circuit open or short.

Output shaft speed sensor malfunction.

Foreign material being attached or sensor installed
improperly.

Gear damaged.
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Turn ignition switch OFF and then ON.
2) Clear DTC, shift selector lever to “2” range and drive vehicle at 3500 r / min engine speed for 3.5 seconds.
3) Stop vehicle and check DTC.

7B-32 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
STALL TEST
This test is to check overall performance of automatic transmission
and engine by measuring stall speed at D and R ranges.
Be sure to perform this test only when transmission fluid is at normal
operating temperature (70–80C / 158–176F) and its level is be-
tween FULL HOT and LOW HOT. (Refer to “Fluid level” in this sec-
tion.)
CAUTION:
Do not run engine at stall more than 5 seconds continuous-
ly, for oil temperature may rise excessively high.
1) Install tachometer.
2) Apply parking brake and block vehicle wheels.
3) Start engine with selector lever shifted to P range.
4) Depress brake pedal.
5) Shift selector lever to D range and depress accelerator pedal ful-
ly while watching tachometer. Read engine rpm quickly when it
has become constant (stall speed).
6) Release accelerator pedal immediately after stall speed is
checked.
7) In the same way, check stall speed at R range.
8) Stall speed should be within following specification.
Stall speed: 2,500 – 2,900 r / min
(For both G10 and G13 engine models)
9) Possible causes for out-of-specification stall speed are as fol-
lows. Check each part which is suspected to be the cause.
Stall speed measured
Possible causes
Lower than specification
Engine output insufficient

Torque converter defective
Higher than specification in
D range
Forward clutch slippage

One-way clutch defective
Higher than specification in
R range
Direct clutch slippage

1st-reverse brake slippage

1. Front drive shaft (LH)
2. Oil pan
AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-33
LINE PRESSURE TEST
This test is to check oil pressure system for operation by measuring
oil pressure in oil pressure line. Make sure to perform this test only
when transmission fluid is at normal operating temperature.
NOTE:

Make sure that transmission fluid level is between FULL HOT
and LOW HOT marks on oil level gauge at normal operating
temperature which corresponds to 70–80C (155–176F) of
fluid. (Refer to “Fluid level” in this section.)

Check that transmission is free from fluid leakage.
1) With engine at stop, remove plug and connect oil pressure
gauge to plug hole.
Special Tool
(A): 09925-37811-001
2) Install tachometer.
3) Apply parking brake and block vehicle wheels.
4) With selector lever shifted to P range, start engine.
5) Depress brake pedal fully.
6) Shift selector lever to D range and check oil pressure with engine
running at idling speed and at stall speed respectively.
7) Repeat the same check as in step 6) with selector lever shifted
to R range.
CAUTION:
Do not run engine at stall more than 5 seconds continu-
ously, for oil temperature may rise excessively high.
8) If line pressure is within respective specification in table below,
oil pressure system is in good condition.
[G10 Engine Model]
Engine speedLine pressureEngine s eedD rangeR range
Idling speed
200 – 390 kPa
2.0 – 3.9 kg / cm2
28.4 – 55.5 psi
540 – 780 kPa
5.4 – 7.8 kg / cm2
76.8 – 110.9 psi
Stall speed
390 – 590 kPa
3.9 – 5.9 kg / cm2
55.5 – 83.9 psi
880 – 1230 kPa
8.8 – 12.3 kg / cm2
125.1 – 174.9 psi
[G13 Engine Model]
Engine speedLine pressureEngine s eedD rangeR range
Idling speed
260 – 460 kPa
2.6 – 4.6 kg / cm2
37.0 – 65.4 psi
660 – 900 kPa
6.6 – 9.0 kg / cm2
93.9 – 128.0 psi
Stall speed
660 – 850 kPa
6.6 – 8.5 kg / cm2
93.9 – 120.9 psi
1330 kPa or more
13.3 kg / cm2 or more
189.0 psi or more