chain TOYOTA 4RUNNER 1998 Owners Manual

4RUNNER (1998)
Even if the power assist is
completely lost, the brakes will
still work. But you will have to
push the pedal hardÐmuch
harder than normal. And your
braking distance will be longer.
ANTI- LOCK BRAKE SYSTEM
(with ºABSº warning light)
The anti- lock brake system is de-
signed to automatically help prevent
lock- up of the wheels during sudden
braking or braking on slippery road
surfaces. This assists in providing
directional stab ility and steering per-
formance of the vehicle under these
circumstances.
The anti- lock brake system becomes
operative after the vehicle has accel-
erated to a speed in excess of
approximately 10 km/h (6 mph). It
stops operating when the vehicle de-
celerates to a speed below approxi-
mately 5 km/h (3 mph).
You may hear a sound in the engine
compartment for a few seconds when
the engine is started or just after the
vehicle is started. This means that the
anti- lock brake system is in the self
check mode, and does not indicate a
malfunction. Effective way to press the ºABSº
brake pedal: When the anti- lock brake
system function is in action, you may
feel the brake pedal pulsating and
hear a noise. In this situation, to let
the anti- lock brake system work for
you, just hold the brake pedal down
more firmly. Do not pump the brake.
This will result in reduced braking per-
formance.
The brake pedal pulsation caused by
the anti- lock brake system may indi-
cate hazardous road surface condi-
tions. Although the anti- lock brake
system assists in providing vehicle
control, it is still important to drive
with all due care, because the anti-
lock brake system cannot overcome
the laws of physics that act on your
vehicle:
Braking capab ility is dependent on
tire friction with the road surface.
Even though the anti- lock brake
system is operating, a driver can-
not maintain full control on certain
slippery road surfaces, when cor-
nering at high speeds, or in violent
maneuvers.
Avoid high speeds on wet roads.
The anti- lock brake system cannot
eliminate the risk of hydroplaning
and loss of tire friction. Always maintain a safe distance from
the vehicle in front of you. Compared
with vehicles not fitted with an anti-
lock brake system, your vehicle may
require a longer stopping distance in
the following cases:
Driving on rough, gravel or snow-
covered roads.
Driving with tire chains installed.
Driving on roads where the road
surface is pitted or has other differ-
ences in surface height.
CAUTION
Do not use tires other than the
manufacturer 's designated tires,
and do not mix tires or wheels of
different sizes. You may prevent
the antilock brake system from
operating at full effectiveness.
Vehicles with rear differential lock sys-
tem 'The anti- lock brake system does
not operate when the rear differential
is locked. It is normal operation for
the ºABSº warning light to be on at
this time.

4RUNNER (1998)
Use a washer fluid containing an
antifreeze solution.
This product is available at your Toyo-
ta dealer and most auto parts stores.
Follow the manufacturer 's directions
for how much to mix with water.
NOTICE
Do not use engine antifreeze or any other substitute because itmay damage your vehicle's paint.
Do not use your parking brake
when there is a possibility it could
freeze.
When parking, put the transmission
into ºPº (automatic) or into first or
reverse (manual) and block the rear
wheels. Do not use the parking brake,
or snow or water accumulated in and
around the parking brake mechanism
may freeze, making it hard to release.
Keep ice and snow from accumulat-
ing under the fenders.
Ice and snow built up under your
fenders can make steering difficult.
During bad winter driving, stop and
check under the fenders occasionally. Depending on where you are driv-
ing, we recommend you carry some
emergency equipment.
Some of the things you might put in
the vehicle are tire chains, window
scraper, bag of sand or salt, flares,
small shovel, jumper cables, etc.
Trailer towing
Your vehicle is designed primarily as
a passenger- and- load- carrying ve-
hicle. Towing a trailer will have an
adverse effect on handling, perfor-
mance, braking, durability and driving
economy (fuel consumption, etc.).
Your safety and satisfaction depend
on the proper use of correct equip-
ment and cautious driving habits. For
your safety and the safety of others,
you must not overload your vehicle or
trailer. Ask your local Toyota dealer
for further details before towing.
WEIGHT LIMITS
Before towing, make sure the total
trailer weight, gross combination
weight, gross vehicle weight, gross
axle weight and trailer tongue load
are all within the limits.
The total trailer weight and tongue
load can be measured with platform
scales found at a highway weighing
station, building supply company,
trucking company, junk yard, etc.

4RUNNER (1998)
Total trailer weight
Tongue load
Tongue load
Total trailer weight
100 9 to 11 %
The trailer cargo load should be
distributed so that the tongue
load is 9 to 11% of the total
trailer weight, not exceeding the
maximum of the following. Nev-
er load the trailer with more
weight in the back than in the
front. About 60% of the trailer
load should be in the front half
of the trailer and the remaining
40% in the rear.
3RZ- FE engine158 kg (350 lb.)
5VZ- FE engine 226 kg (500 lb.)HITCHES
Use only a weight carrying hitch
designed for the total trailer weight.
Toyota does not recommend using
a weight distribution (load equaliz-
ing) hitch.
The hitch must be bolted securely
to the vehicle frame and installed
according to the hitch manufactur-
er 's instructions.
The hitch ball and king pin should
have a light coat of grease.
Toyota recommends removing the
hitch when not towing to preventin-
jury and/or damage due to the
hitch in event of a rear end colli-
sion. After removal of the hitch,
seal the installation area to prevent
entry of exhaust fumes and mud.
NOTICE
Do not use an axle- mounting
hitch as it may cause damage tothe axle housing, wheel bearings,wheels and or tires.
BRAKES AND SAFETY CHAINS
Toyota recommends trailers with
brakes that conform to any appli-
cable federal and state/provincial
regulations.

4RUNNER (1998)
A safety chain must always be
used between the towing vehicle
and the trailer. Leave sufficient
slack in the chain for turns. The
chain should cross under the
trailer tongue to prevent the
tongue from dropping to the
ground in case it becomes dam-
aged or separated. For correct
safety chain procedures, follow
the hitch or trailer manufactur-
er 's recommendations.
CAUTION
If the total trailer weight ex-
ceeds 453 kg (1000 lb.), trailer
brakes are required .
Never tap into your vehicle's
hydraulic system as it would
lower its braking effectiveness .
Never tow a trailer without us-
ing a safety chain securely atta-
ched to both the trailer and the
vehicle. If damage occurs to the
coupling unit or hitch ball,
there is danger of the trailer
wandering over into another
lane.
TIRES
Ensure that your vehicle's tires are
properly inflated. See Chapter 7- 2
for instructions.
The trailer tires should be inflated
to the pressure recommended by
the trailer manufacturer in respect
to the total trailer weight.
TRAILER LIGHTS Trailer lights must comply with fed-
eral, state/provincial and local re-
gulations. See your local recre-
ational vehicle dealer or rental
agency for the correct type of wir-
ing and relays for your trailer.
Check for correct operation of the
turn signals and stop lights each
time you hitch up. Direct splicing
may damage your vehicle's electri-
cal system and cause a malfunc-
tion of your lights.
BREAK- IN SCHEDULE Toyota recommends that you do
not tow a trailer with a new vehicle
or a vehicle with any new power
train component (engine, transmis-
sion, differential, wheel bearing,
etc.) for the first 800 km (500
miles) of driving. MAINTENANCE
If you tow a trailer, your vehicle
will require more frequent
maintenance due to the additional
load. For this information, please
refer to the scheduled maintenance
information in the ºOwner 's Manual
Supplement/Maintenance Scheduleº.
Retighten all fixing bolts of the
towing ball and bracket after
approximately 1000 km (600 miles)
of trailer driving.
PRE- TOWING SAFETY CHECK
Check that your vehicle remains
level when a loaded or unloaded
trailer is hitched. Do not drive if
the vehicle has an abnormal nose-
up or nose- down condition, and
check for improper tongue load,
overload, worn suspension or other
possible causes.
Make sure the trailer cargo is se-
curely loaded so that it cannot
shift.
Check that your rear view mirrors
conform to any applicable federal,
state/provincial or local regulation.
If not, install the rear view mirrors
required for towing purpose.

4RUNNER (1998)
Only when you cannot receive a
towing service from a Toyota dealer
or commercial tow truck service,
tow your vehicle carefully in accor-
dance with the instructions given in
ºÐEmergency towingº in this Part.
Proper equipment will help ensure that
your vehicle is not damaged while be-
ing towed. Commercial operators are
generally aware of the state/provincial
and local laws pertaining to towing.
Your vehicle can be damaged if it is
towed incorrectly. Although most oper-
ators know the correct procedure, it is
possible to make a mistake. To avoid
damage to your vehicle, make sure
the following few precautions are ob-
served. If necessary, show this page
to the tow truck driver. TOWING PRECAUTIONS:
Use a safety chain system for all tow-
ing, and abide by the state/provincial
and local laws. The wheels and axle
on the ground must be in good condi-
tion. If they are damaged, use a tow-
ing dolly.
Two- wheel drive modelsÐ
(a) Towing with wheel lift type
truck
From frontÐ Manual transmission:
We recommend using a towing dolly
under the rear wheels. If you do not
use a towing dolly, release the park-
ing brake and put the transmission
in neutral.
Automatic transmission:
Use a towing dolly under the rear
wheels.
NOTICE
Never tow a vehicle with an auto-
matic transmission from the frontwith the rear wheels on theground, as this may cause serious
damage to the transmission.
From rearÐ Place the ignition key in
the ºACCº position.
NOTICE
When lifting wheels, take care
to ensure adequate groundclearance for towing at the op-posite end of the raised vehicle.
Otherwise, the bumper and/orunderbody of the towed vehiclewill be damaged during towing.
Do not tow with the key re-moved or in the ºLOCKº posi-tion, as the steering lock mech-
anism is not strong enough tohold the front wheels straight
while towing.
(b) Using flat bed truck

4RUNNER (1998)
If towing is necessary, we recom-
mend you to have it done by your
Toyota dealer or a commercial tow
truck service.
If towing service is not available in
an emergency, your vehicle may be
temporarily towed by a cable or
chain secured to the emergency
towing hook. Use extreme caution
when towing vehicles.
A driver must be in the vehicle to
steer it and operate the brakes.
Towing in this manner may be done
only on hard- surfaced roads for a
short distance and at low speeds.
Also, the wheels, axles, drive train,
steering and brakes must all be in
good condition.
CAUTION
Use extreme caution when towing
vehicles. Avoid sudden starts or
erratic driving maneuvers which
would place excessive stress on
the emergency towing hook and
towing cable or chain. The hook
and towing cable or chain may
break and cause serious injury or damage.
NOTICE
Use only a cable or chain specifi-
cally intended for use in towingvehicles. Securely fasten the cableor chain to the towing hook pro-
vided.
Before towing, release the parking
brake and put the transmission in neu-
tral (manual) or ºNº (automatic) and
the transfer in ºH2º (four- wheel drive
models). The key must be in ºACCº
(engine off) or ºONº (engine running).

4RUNNER (1998)
CAUTION
If the engine is not running, the
power assist for the brakes and
steering will not work so steering
and braking will be much harder
than usual.
Before emergency towing, check
that the hook is not broken or
damaged and that the installation
bolts are not loose.
Fasten the towing cable or chain
securely to the hook.
Do not jerk the hook. Apply steady
and even force.
To avoid damaging the hook, do
not pull from the side or at a verti-
cal angle. Always pull straight ahead.CAUTION
If the emergency towing eyelet is
used to get out when your vehicle
becomes struck in mud, sand or
other condition from which the
vehicle cannot be driven out un-
der its own power, make sure to
observe the precautions men-
tioned below. Otherwise, exces-
sive stress will be put on the
eyelet and the towing cable or
chain may break, causing serious
injury or damage. If the towing vehicle can hardly
move, do not forcibly continue
the towing. Contact your Toyota
dealer or a commercial tow
truck service for assistance.
Tow the vehicle as straight
ahead as possible.
Keep away from the vehicle
during towing.
ÐEmergency towing hook pr
cautions

4RUNNER (1998)
The following methods are effective to
get out when your vehicle is struck in
mud, sand or other condition from
which the vehicle cannot be driven out
under its own power. Use extreme
caution when towing vehicles. In addi-
tion, keep away from the vehicles and
towing cable or chain when towing.
Remove the soil and sand in the
front and the back of the tires.
Place a stone or wood under the
tires.
If you cannot shift the selector le-
ver out of ºPº position to other
positions even though the brake
pedal is depressed, use the shift
lock override button as follows: 1. Turn the ignition key to ºLOCKº
position. Make sure the parking
brake is set.
2. Pry up the cover with a flat- bladed screwdriver or equivalent.
ÐTips for towing a stuck
vehicle
If you cannot shift automa
t
transmission selector lever
(two- wheel drive models)

4RUNNER (1998)
Part 7
DO- IT- YOURSELF
MAINTENANCEÐ
Chapter 7- 2
Engine and Chassis
Checking the engine oil level
Checking the engine coolant
level
Checking brake fluid
Checking power steering fluid
Checking tire pressure
Checking and replacing tires
Rotating tires
Installing snow tires and
chains
Replacing wheels
Aluminum wheel precautions
Checking the engine oil level

4RUNNER (1998)
Tread wear indicator
CHECKING YOUR TIRES
Check the tire tread for the tread
wear indicators. If the indicators
show, replace the tires.
The tires on your Toyota have built- in
tread wear indicators to help you
know when the tires need replace-
ment. When the tread depth wears to
1.6 mm (0.06 in.) or less, the indica-
tors will appear. If you can see the
indicators in two or more adjacent
grooves, the tire should be replaced.
The lower the tread, the higher the
risk of skidding.
The effectiveness of snow tires is
lost if the tread wears down below
4 mm (0.16 in.). Check the tires regularly for dam-
age such as cuts, splits and cracks.
If any damage is found, consult
with a technician and have the tire
repaired or replaced.
Even if the damage does not appear
serious, a qualified technician should
examine the damage. Objects which
have penetrated the tire may have
caused internal damage.
Any tires which are over six years
old must be checked by a qualified
technician even if damage is not
obvious.
Tires deteriorate with age even if they
have never or seldom been used.
This also applies to the spare tire and
tires stored for future use.REPLACING YOUR TIRES
When replacing a tire, use only the
same size and construction as origi-
nally installed and with the same or
greater load capacity.
Using any other size or type of tire
may seriously affect handling, ride,
speedometer/odometer calibration,
ground clearance, and clearance be-
tween the body and tires or snow
chains.