ignition TOYOTA AVALON 1996 Owners Manual

3
1. Instrument panel light control dial
2. Headlight and turn signal switch
3. Wiper and washer switches
4. Driving pattern selector button
5. Thermometer
6. Clock
7. Emergency flasher switch
8. Car audio
9. Miscellany box
10.Air conditioning controls
11. Ashtray and cigarette lighter
12.Rear window defogger switch
13.Ignition switch
14.Cruise control switch
15.Power rear view mirror control switch
16. Headlight cleaner switch
ProCarManuals.com

8
LOCKING AND UNLOCKING WITH
KEY
Insert the key into the keyhole and turn
it.
To lock: Turn the key forward.
To unlock: Turn the key backward.
All the doors lock and unlock simulta-
neously with either front door. In the driv-
er 's door lock, turning the key once will un-
lock the driver's door and twice in
succession will unlock all the doors simul-
taneously.LOCKING AND UNLOCKING WITH IN-
SIDE LOCK KNOB
Move the lock knob.
To lock: Push the knob forward.
To unlock: Pull the knob backward.
Closing the door with the lock knob
pushed in w ill also lock the door. Be care-
ful not to lock your keys in the vehicle.
The door cannot be locked if you leave the
key in the ignition switch.Driver's side
Passenger 's side
Side doorsÐ
ProCarManuals.com

10
Locking operation
Unlocking operationYour vehicle has a wireless remote
control
system that can lock or unlock
all the doors from a distance within
approximately 1 m (3 ft.) of the outside
handle of the driver's door. When op-
erated within approximately 1 m (3 ft.)
of the trunk lid, this system also opens
the trunk lid.
To lock or unlock all the doors, push
the switches of the transmitter.
To lock: Push the LOCKº switch. All the
doors are locked simultaneously.
To unlock: Push the UNLOCKº switch
once to unlock the driver's door alone.
Pushing the switch twice within 5 seconds
unlocks all the doors simultaneously.
If any of the doors is not securely closed,
or if the key is in the ignition switch, locking
cannot be performed by the LOCKº
switch.
You have 30 seconds to open a door after
using the wireless unlock feature. If a door
is not opened by then, all the doors will be
automatically locked again.
If pushing the LOCKº or UNLOCKº
switch does not actuate the doors, and
you have checked the battery in the trans-
mitter, consult your Toyota dealer.
To open the trunk lid, push the trunk
lid open switch.
To open the trunk lid with the master key,
see Trunk lidº.
If the wireless remote control transmitter
does not operate from a normal distance:

Check the batteries in the transmitter.
To replace the batteries, see Replac-
ing transmitter batteriesº.

Check for closeness to a radio trans-
mitter such as a radio station or an air-
port which can interfere with normal
operation of the transmitter.
ÐWireless remote control
ProCarManuals.com

11
Wireless remote control transmitter:

Avoid knocking it hard against other
objects.

Avoid putting it in water.
Replacing transmitter batteries
The expected life of your transmitter bat-
teries is about one year. For replacement,
use DURACELL
[ DL2016 or equivalent.
a. Using a screwdriver, separate the two
halves of the transmitter with the transmit-
ter buttons facing down.
Take care not to damage the rubber gas-
ket during removal.
b. Remove and replace the transmitter
batteries.
If you touch a new battery with your fin-
gers, clean it with rubbing alcohol. Skin
oils may shorten the batteries' life.
c. Reassemble the transmitter case.
Make sure the gasket is properly installed.
After replacing batteries, check that the
transmitter operates properly. If the trans-
mitter still does not operate properly, con-
tact your Toyota dealer.
MODEL/FCC ID: GQ43VT7T
ISC: 1470 K1361
MADE IN U.S.A.
This device complies with part 15 of the
FCC rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and (2) This device must
accept any interference received, in-
cluding interference that may cause un-
desired operation.
The windows can be operated with the
switch on each door.
The power windows work when the igni-
tion switch is in the ONº position. Howev-
er, if both front doors are closed, they work
for 60 seconds even after the ignition
switch is turned off. They stop working
when either front side door is opened.
OPERATING THE DRIVER'S WINDOW
Use the switch on the driver's door.
Normal operation: The window moves
as long as you hold the switch.
To open: Lightly push down the switch.
To close: Pull up the switch.
Power windows
ProCarManuals.com

16
To deter the vehicle theft, the system is
designed to give an alarm and keep the
engine from being started if any of the
doors, trunk or hood is forcibly un-
locked or the battery terminal is dis-
connected and then reconnected
when the vehicle is locked.
The alarm blows the horn intermittently
and flashes the headlights, tail lights and
other exterior lights. The engine cannot
be started because the starter circuit will
be cut.SETTING THE SYSTEM
1. Turn the ignition key to the LOCKº
position and remove it.
2. Have all passengers get out of the ve-
hicle.
3. Close and lock all the doors, trunk and
hood.
The indicator light will come on when all
the doors, trunk and hood are closed and
locked.
As the doors are locked, the system will
give you a preparation time of 30 seconds
before the setting, during which the doors,
trunk and hood may be opened to prepare
for the setting. Be careful not to use the key or wireless
remote control transmitter when opening
any door. This will cancel the system.
4. After making sure the indicator light
starts fl
ashing, you may leave the vehicle.
The system will automatically be set after
the preparation time passes. The indica-
tor light will flash to show the system is
set. If any of the doors, trunk or hood is
open at that time, the setting is interrupted
until it is closed and locked.
Never leave anyone in the vehicle when
you set the system, because unlocking
from the inside will activate the system.
WHEN THE SYSTEM IS SET
Activating the system
The system will give the alarm and cut the
starter circuit under the following condi-
tions:

If any of the doors, trunk or hood is un-
locked without using the key or wire-
less remote control transmitter

If the battery terminal is disconnected
and then reconnected
After one minute, the alarm will automati-
cally stop with the starter circuit cut kept
on.
Theft deterrent system
ProCarManuals.com

17
Reactivating the alarm
Once set, the system automatically resets
the alarm each time all the doors, trunk
and hood are closed after the alarm stops.
The alarm will be activated again under
the following conditions:

If any of the doors, trunk or hood is
opened

If the battery terminal is disconnected
and then reconnected
Stopping the alarm
Turn the ignition key from the LOCKº to
ACCº position. The alarm w ill be stopped
with the starter circuit kept on. Stopping
the alarm in this manner will keep the
alarm from being reactivated when any of
the doors, trunk or hood is opened.
Interrupting the setting
With the system set, the trunk can be
opened with the key or wireless remote
control transmitter without setting off the
system. While the truck is open, the set-
ting is interrupted and the doors and hood
may be opened in addition. However,
when the battery terminal is reconnected,
the system is activated. Close and lock the doors and hood, and
the system will automatically be reset af-
ter two seconds when the trunk is closed
with the key removed.
CANCELLING THE SYSTEM
Unlock either front door with the key or
wireless remote control transmitter. This
cancels the system completely and the
starter ci
rcuit cut will be cancelled at once.
INDICATOR LIGHT
The indicator light gives the following
three indications.
FLASHINGÐThe system is set. You
need the key or wireless remote control
transmitter to open the doors, trunk and
hood.
ONÐThe system will automatically be set
when the time comes. The doors, trunk
and hood may be opened without a key or
wireless remote control transmitter.
OFFÐThe system is inactive. You may
open any door, trunk and hood. TESTING THE SYSTEM
1. Open all the windows
2. Set the system as described above.
The doors should be locked with the key
or wireless remote control transmitter. Be
sure to wait until the indicator light starts
flashing.
3. Unlock any door from the inside. The
system should activate the alarm.
4. Cancel
the system by unlocking any of
the doors with the key or wireless remote
control transmitter.
5. Repeat this operation for the other
doors, trunk and hood. When testing on
the hood, also check that the system is ac-
tivated when the battery terminal is dis-
connected and then reconnected.
If the system does not work properly, have
it checked by your Toyota dealer.
ProCarManuals.com

19
Sliding operation
Tilting operationTo operate the moon roof, use the
switches beside the interior light.
The moon roof works when the ignition
switch is in the ONº position. However, if
all the doors are closed, it works for 60
seconds even after the ignition switch is
turned off. It stops working when any of
the doors are opened.
Sun shade operationÐ
The sun shade can be opened or closed
by hand.
Sliding operationÐ
To open: Push the switch on the SLIDEº
side.
The sun shade will be opened together
with the roof.
To close: Push the switch on the opposite
side of the SLIDEº side.
As a precaution when closing, the roof
stops at the three-quarters closed posi-
tion before fully closing. Therefore, re-
lease the switch and then push it again to
close it completely.
Tilting operationÐ
To tilt up: Push the switch on the UPº
side.
To lower: Push the switch on the opposite
side of the UPº side.
You may stop the moon roof at any de-
sired
position. The roof will move while the
switch is being pushed and stop when re-
leased.
CAUTION!
To avoid serious personal injury, you
must do the following.

While the vehicle is moving, always
keep the head, hands and other
parts of the body of all occupants
away from the roof opening. Other-
wise, you could be seriously in-
jured if the vehicle stops suddenly
or if the vehicle is involved in an ac-
cident.

Always make sure nobody places
his/her head, hands and other parts
of the body in the roof opening be-
fore you close the roof. If some-
one's neck, head or hands gets
caught in the closing roof, it could
result in a seri ous injury. When any-
one closes the roof, first make sure
it is safe to do so.

Never leave small children alone in
the vehicle, especially with the igni-
tion key still inserted. They could
use the moon roof switches and get
trapped in the roof opening. Unat-
tended children can become in-
volved in serious accidents.

Never sit on top of the vehicle
around the roof opening.
Electric moon roof
ProCarManuals.com

32
This indicator comes on when the
ignition key is turned to the ACCº or
ONº position. It goes off after about 6
seconds. This means the SRS airbags
are operating properly.
The SRS airbag warning light system
monitors the airbag sensor assembly, in-
flators, warning light, interconnecting wir-
ing and power sources.The SRS airbag system is designed to
activate in response to a severe frontal
impact within the shaded area be-
tween the arrows in the illustration.
The SRS airbags will deploy if the severity
of the impact is above the designed
threshold level, comparable to an approxi-
mate 20 km/h (14 mph) collision when im-
pacting straight into a fixed barrier that
does not move or deform.
If the severity of the impact is below the
above threshold level, the SRS airbags
may not deploy. However, this threshold velocity will be
considerably higher if the vehicle strikes
an object, such as a parked vehicle or sign
pole, which can move or deform on im-
pact, or if it is
involved in an underride col-
lision (e.g. a collision in which the nose of
the vehicle underridesº, or goes under,
the bed of a truck).
It is possible with collision severity at the
marginal level of airbag sensor detection
and activation that only one of your ve-
hicle's two airbags will deploy.
For the safety of all occupants, be sure to
always wear seat belts.
ProCarManuals.com

36
Do not perform any of the followingchanges without consulting your
Toyota dealer. Such changes caninterfere with proper operation ofthe SRS airbag system in somecases.
Installation of electronic itemssuch as a mobile two-way radio,
cassette tape player or compactdisc player
Modification of the suspension
system
Modification of the front endstructure
Attachment of a grille guard (bullbar, kangaroo bar, etc.), snow-
plow, winches or any other equip-ment to the front end
Repairs made on or near the con-sole, steering column, steeringwheel or dashboard near the frontpassenger airbag
NOTICE
This SRS airbag system has a service re-
minder indicator to inform the driver of op-
erating problems. If either of the following
conditions occurs, this indicates a mal-
function of the airbags. Contact your To-
yota dealer as soon as possible to service
the vehicle.

The light does not come on when the
ignition key is turned to the ACCº or
ONº position, or remains on.

The light comes on while driving.In the following cases, contact your Toyo-
ta dealer as soon as possible:

The SRS airbags have been inflated.

The front part of the vehicle (shaded in
the illustration) was involved in an ac-
cident not of the extent to cause the
SRS airbags to inflate

The pad section of the steering wheel or
front passenger airbag cover (shaded in
the illustration) is scratched, cracked, or
otherwise damaged.
ProCarManuals.com

Part 1
49
OPERATION OF
INSTRUMENTS AND
CONTROLSÐ
Chapter 1-4
Lights, Wipers
and Defogger

Headlights and turn signals

Emergency flashers

Instrument panel light control

Interior light

Front personal lights

Rear personal lights

Ignition switch light

Windshield wipers and washer

Headlight cleaner

Rear window defoggerHEADLIGHTS
To turn on the following lights: Twist
the headlight/turn signal lever knob.
Position 1ÐParking, tail, license plate,
side marker and instrument panel lights
Position 2ÐHeadlights and all of the
above
Position 3 (AUTOº)ÐHeadlights and/or all
of the above
They automatically turn on or off depend-
ing on the darkness of the surroundings.
Manually twist the knob to the position 2
to turn on the headlights if they are need-
ed immediately when entering a dark tun-
nel, parking structure, etc.The automatic light control sensor is on the
top of the driver 's side instrument panel.
Do not place anything on the instrument
panel, and/or do not affix anything on the
windshield to block this sensor.
If you feel that the automatic light control
comes into operation too early or too late,
have the sensor adjusted by your Toyota
dealer.
The lights automatically turn off when the
driver's door is opened with the ignition
key in the ACCº or LOCKº position. To
turn them on again, turn the key to the
ONº position or actuate the headlight
switch. If you are going to park for over
one week, make sure the headlight switch
is off.
Headlights and turn signals
(with automatic light control
system)
ProCarManuals.com